change wheel AUDI S6 2014 Owner's Manual

264 What do I do now?
&_ WARNING
You or your passengers could be injured
while changing a wheel if yo u do n ot fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis­
tance
off the road. Turn off the engine,
turn the emergency flashers on and use other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traff ic.
- T o help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
ja ck, always fully set the parking b rake
and bloc k the whee l diagona lly opposite
the whee l being changed. When one
front whee l is lifted off the gro und, plac­
ing the Automat ic Transmiss ion in P
(Park) will
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced t ire i n the luggage com­
partment
c> page 134.
Before chang ing the wheel, yo u m ust acti­
vate the jacking mode, so that the auto­ mat ic cont rols for the Adaptive Air S us­
pens ion* do not make it more difficult to
lift the vehicle with the jack
c> page 266.
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Activate the vehicle jack mode*
~page 266.
-
2. Remove the decorative wheel cov er* . For
mo re details see also
c> page 265, Deco­
rative wheel covers
or c> page 265,
Wheels with wheel bolt caps.
3 . L oosen the wheel bolt s c> page 265.
4. Locate the proper mounting point for the
jack and alig n the jack below that point
c> page 266 .
5.
Raise the car with the jack c> page 266.
6. Remove the wheel with the flat tire and
then insta ll
the s pare c>page 267.
7. Tighten all whee l bolts lightly.
8 . Lower the vehicle with the jack .
9. Use the wheel bolt wrench and firmly
t igh ten al l w heel bo lts c> page 265.
10. Replace the decora tive wh eel co ver*.
11. Deactivate the vehicle jack mode * in the
MMI:
I CARI f u nction button > (Car )* sys­
tems
control button > Se rvicing & chec ks
> A ir susp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above
6 mph (1 0 km/h) .
&_ WARNING ,.__
Always read and follow all WARNINGS and
i nformat ion
c> &. in Raising the vehicle on
page 266
and c> page 268.
After changing a wheel
A wheel change is not complete without the
doing the following.
.,. Always store the vehicle tool kit, the jack*
and the rep laced tire in the luggage com­
partment
c> page 134.
.,. Check the tire pressu re on the spare whee l
immed iate ly after mounting it .
.,. As soon as poss ible, have the
tight ening
torques
on all whee l bolts checked with a
t o rque wrenc h. The co rrect tighte ning tor ­
que is 90 ft lb (120 Nm).
.,. Have the fla t tire
replaced as soon as possi­
b le.
(D Tips
- If you not ice th at the wheel bo lts a re
co rroded and difficult to turn while
changing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked .
ll-

266 What do I do n ow ?
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury .
@ Tips
-Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bo lts.
- If a whee l bolt is very tight, you may find
it easier to loosen by carefully pushing
down on the end of the wheel bolt
wrench w ith
one foot only. As you do so,
hold on to the car to keep your balance
and take care not to slip .
Raising the vehicle
The vehicle must be li~ed with the jack first
before the wheel can be removed .
Fig. 209 Sill pa nels : m ark ings
~
9
---;~ :~-;;:--~
Fi g. 210 Sill : pos ition ing the ve hicle jack
., Activate the vehicle jack mode* in the M MI:
I CAR ! func tion button > (C ar )* sys te m s con ­
t ro l butto n
> Servici ng & che cks> Air su sp. :
j ack mode > On .
.. Engage the par king br ake to prevent your
vehicle from ro lling unintentionally.
., Move the
selector le ver to posit ion P.
.. Find the marking (imprint) on the sill that is
nearest the whee l that will be changed
¢
fig. 209. Be hind the marking, there is a
lift ing point on the sill for the vehicle jack .
., Vehicles with a sill: remove the cover from
the sill before lift ing the veh icle w ith a vehi ­
cle jack ¢
page 267.
., Turn the vehicl e jack located under the lift­
ing point on the sill to ra ise the jack u nti l its
arm
@ ¢fig. 210 is located under the des­
ignated p lastic mount ¢ _&. ¢(D.
.. Align the jack so that its
arm @¢fig . 210
engages in the designated lifting point in
the door si ll and the movable base @ lies
flat on the ground. The base ® must be
ver­
t ical
under the lifting point @ .
., Wind the jack up further until the flat t ire
comes off the ground ¢
,&..
Position t he veh icle jack onl y under the desig­
nated lifting points on the s ill ¢
fig . 209 .
T here is exactly
one locat ion for each wheel.
T he jack must not be positioned at any other
location ¢ _& ¢(j) .
An
un stab le surfa ce under the jack can cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground .
If nec­
essary place a sturdy board or sim ilar support
u nder the jack. On
h ard , s lipp ery surf aces
(such as tiles) use a rubber mat or similar to
preve nt the jack from slipping ¢
.&..
A WARNING
--You or your passengers co uld be injured
while changing a wheel if you do not fo l­
low these safety precautions:
- Position the vehicle jack on ly at the
designated lifting poi nts and align the
jac k. Otherw ise, the vehicle ja ck could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or uns table su rface under the
j ack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessary,
use a sturdy board under the jack. ,..

-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping .
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to
raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­
matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles : wit h sill
Fig. 211 Sill: remov ing t he cover
.,. Pull the cover down to remove it c'> fig. 211.
.,. To install the cover again, insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
What do I do now? 267
@ Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fig. 212 Changing a wheel: using the screwdrive r han­
dle (w it h th e blade re m oved) to turn the bolt s
Fig. 213 Changing a wheel : alignment p in in sid e the
top hole
After you have loosened all wheel bolts and
raised the vehicle
off the ground, remove and
replace the wheel as follows :
Removing the wheel
.,. Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top­
most wheel bolt and set it aside on a clean
surface c>fig. 212 .
.,. Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
empty bolt hole r::;;fig . 213 .
.,. Then remove the other wheel bolts as de­
scribed above .
.,. Take
off the wheel leaving the alignment pin
in the bolt hole
r::;; d). ..,.

268 What do I do no w?
P uttin g on the spare wheel
.. Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
t ighten the remaining wheel bolt slightly
l ike the rest .
.. Turn the jack handle counte r-clockw ise to
lower the vehicle unt il the jac k is fully re­
leased.
.. Use the wheel bolt wrench to tighten all
wheel bolts firmly¢
page 265 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.
When removing or installing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
(j) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversible blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the wheel bo lts.
- When mounting tires with
unid ir ec tional
tread design
make su re the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
t h e mat ing s urfaces of both the whee l
and the h ub. Remove al l dirt from these
s ur faces before remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a sp are t ire w ith a tre ad pattern
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection , please
note the following :
- The direct ion of rotation is marked by an ar­
row on the side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the tire will not be able to
achieve its optim um performance cha racte r­
is tic s wit h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu la r at­
t en tion to th is fact d uring wet wea ther and
t ha t you adjust you r speed to match road
conditions .
- Replace the fl at tir e with a new o ne an d
have it insta lled on you r vehicle as soon as
possible to resto re the handling advantages
of a u nidirectional tire .
Notes on wheel changing
Please read the information¢ page 251, New
tires and replacing tires and wheels
if you a re
going to use a spare tire which is different
from the ti res on your vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after install ation.
- Have th e whe el bolt tightening torque
c hecked with a torque wrench as soon a s
possible by your author ized Audi dealer or
a qualified service stat ion.
- With steel and alloy wheel rims, the wheel
bolt s are cor re ctl y tightened at a torque of
90 ft lb (120 Nm ).
- If you noti ce that the wheel bolts are cor­
roded and diffi cult to turn while changing
a ti re , they should be replaced before you
check the t ightening torque. .,..