change wheel AUDI S6 2015 Owner's Manual

M N
0 I.J "". rl I.O
"' rl
"' rl
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
@ Tips
- Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
- If a wheel bolt is very tight, you may find
it easier to loosen by carefully push ing
down on the end of the wheel bolt
wrench with
one foot only. As you do so,
hold on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jock first
before the wheel con be removed .
Fig. 209 Sill pane ls: markings
'ii
9
--~~ :;:~:'.'"'-i
Fi g. 210 Sill: posit ion ing th e ve hicle jack
~ Activate the vehicle jack mode* in the M MI:
I CAR I funct ion button> ( C ar)* s ystem s con­
t rol button >
Servicing & c heck s > Air susp.:
jack mode
> On .
~ Engage the parking bra ke to prevent your
vehicle from rol ling un intentionally.
~ Move the selector le ver to position P.
What do I d o now ? 275
~ Fi nd the marking (imprint) on the sill that is
nearest the whee l that will be changed
r::!) fig. 209. Beh ind the marking, there is a
lift ing point on the sill for the veh icle jack.
~ Vehicles w ith a sill: remove the cover from
the sill before lift ing the veh icle with a vehi­
cle jack
r::!) page 2 76.
~ Tu rn the v ehicle ja ck located under the lift­
ing point on the sill to ra ise the jack unt il its
a rm @<::!)
fig. 210 is lo cated under the des­
ig nated p lastic moun t
r::!) .&, r::!)(D,
~ Align the jack so that its arm@ r::::> fig. 210
engages in the designated lifting point i n
the door s ill and the movable base ® lies
flat on the ground. The base @ must be
ver­
tical
under the lifting point @.
~ Wind the jack up further until the flat t ire
comes off the ground
r::!) & .
Position the vehicle jack only under the desig­
nated lifting points on the sill
Q fig . 209 .
There is exactly one locat ion for each wheel.
The jack must not be positioned at any other lo c a ti o n
r::!) A r::!) An un stable surface under the jack can cause
the vehicle to slip off the jack . Always provide
a fi rm base for the jack on the g ro und . If nec­
essary p lace a sturdy board or sim ila r support
u nder the jack. On
hard , slippery surfaces
(such as tiles) use a rubbe r mat or similar to
prevent the jack from slipping
r::!) & .
&_ WARNING
-You or your passengers co uld be in ju red
while changing a whee l if you do not fo l­
low t hese safety preca utions:
- Position the vehicle jack on ly at the
d esigna ted lifti ng points and align the
j a ck . O therw ise, the vehicle ja ck could
s lip and cause an injury i f it does not
have sufficient hold on the vehicle.
- A soft or uns table surface unde r the
j ack may cause the ve hicle to slip off
the jack. A lways provide a firm base for
the jack on the ground . If necessary,
use a st urdy boa rd under the jack.
~

276 What do I do now?
-On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you a re
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct , ad­
just as necessary and then continue to raise the jack.
- Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­
ing points on the sill. Otherwise, your vehi­
cle will be damaged.
(D Tips
The vehicle jack mode* switches off auto­ matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles: with sill
Fig . 211 Sill: remov ing t he cover
.. Pull the cover down to remove it¢ fig . 211.
.,. To install the cover again , insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
(D Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off /installing the spare
Follow these instructions st ep-by-step for
changing the wheel.
Fig. 212 Changing a wheel: using the screwdrive r han­
dle (w it h th e blade re m oved) to turn the bolt s
Fig. 213 Changing a wheel: alignment p in ins ide t he
top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.. Use the hexagonal socket in the screwdriv­
er handle
to completely remove the top­
most wheel bolt and set it aside on a
clean
surface ¢ fig. 212 .
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 213 .
.,. Then remove the other wheel bolts as de­
scribed above .
.. Take off the wheel leaving the alignment pin
in the bolt hole
¢(D . Ill>

M N
0 <.J 'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Putting on the spare wheel
"'Lift the spare wheel and ca refully slide it
over the alignment pin to guide it in place
¢ (D .
"' Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
"' Remove the alignment pin and insert and
t ighten the remaining wheel bolt s lightly
like the rest .
"'T urn the jack handle counte r-clockw ise to
lower the vehicle unt il the jac k is f ully re­
l eased .
"' Use the whee l bolt wrench to tighten a ll
whee l bolts firmly
¢ page 274. Tighten
them
crosswis e, from one bolt to the (ap­
proximate ly) opposite one, to keep the
wheel cen tered.
When removing or install ing the wheel,
the rim could hit the brake rotor and dam­
age the rotor. Work carefully and have a
second person help you .
{D) Tips
Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or t ighten
the wheel bolts .
- Pull the reversib le blade from the screw­
driver before you use the hexagonal
socket in the handle to turn the whee l
bo lts.
- When mounting tires with
un id ire ctional
tread design
make s ure the tread pat­
tern is poi nted the right way
¢ page 277.
- The wheel bolts should be clean and easy
to tu rn . Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the h ub. Remove a ll dir t from these
su rfaces before remo unting the wheel.
What do I do now? 277
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Usi ng a spa re ti re with a tre ad patte rn
intended for use in a specific direction
When using a spare t ire with a tread patter n
intended for use in a spec ific d irection, please
note the following :
- The d irect ion of rotation is marked by an ar­
row on t he side of the ti re .
- If the spare tire has to be installed in the in­
correct direct ion, use the spare tire only
temporarily s ince the t ire will not be able to
achieve its optimum performance cha racte r­
istics w it h regard to aquap la ni ng, no ise and
wear .
- We recommend that you pay part icu lar at­
ten tion to th is fact during we t wea ther and
t ha t you adjust your speed to match road
conditions .
- Replace the fl at t ire wi th a new one and
have i t installed on your vehicle as soon as
possible to restore the hand ling advantages
of a un idirectional tire .
Notes on wheel changing
Please read the information¢ page 257, New
tires and replacing tires and wheels
if you a re
go ing to use a spare tire wh ich is different
from the tires on you r vehicle .
After you change a tire:
- Check the tire pre ssure on the spare imme­
diately after installation.
- Have the wheel bolt tightening torqu e
checked with a torque wrench as soon a s
possible by your authorized Audi dealer or
a qualified service station.
- With steel and alloy wheel rims , the wheel
bolts are cor re ctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are cor­
roded and diff icult to turn while changing
a tire , they should be replaced before you
check the t ightening torque. .,,.
•
•

M N
0 <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-----------------------------~I~ n~d~ e~x 303
K
Key ... .... .. .. .... .. .... ... .. .. .... 31
Battery rep lacement master key ... .. .. 32
Emergency key . . . . . . . . . . . . . . . . . . . . . 31
Key not recognized . . . . . . . . . . . . . . . . . . 76
Key replacement . . . . . . . . . . . . . . . . . . . 31
Master key . . . . . . . . . . . . . . . . . . . . . . . . 31
Mechanical key . . . . . . . . . . . . . . . . . . . . . 32
Kick-down tiptronic
K . b nee air ags . ............. .. .. .. .. .
D escr ipt ion .... .. ..... ... .. .. .. .. .
How they work . ... .... ... .. .. .. .. . 111
16 2
162 163
Important safety instructions ... .. .. . 164
L
Lane assist . . . . . . . . . . . . . . . . . . . . . . . . . 93
L ane Change Ass istant
refer to side assist . . . . . . . . . . . . . . . . . . 96
LATCH
.... .. ............. .... .. ... 185
Descr ipt ion . .... ......... .... .. .. . 186
Instal ling a child restraint .. .. .. .. .. . 187
L ocat ion . ............ ...... .... .. 186
M ounting and releasing the ancho rage
hook .. .. .. .... ......... .... .. .. . 187
Launch Contro l Program .... .. .. .. .. . 112
L eather clean ing/protection ... .. .. ... 2 12
L eaving home .. ..... ...... .. .. .. .. .. 45
Lifting jack ........................ 275
L ift ing vehicle
Light 287
Ambie nce lighting ........... .. .... . 46
Com ing/Leavi ng home ......... ... ... 45
D aytime running lig hts .... .. .. .. .. .. 43
E mergency flashers ....... .. .. .. .. .. 44
E xte rio r lighting ... .... ... .. .. .. .. .. 43
Headlig ht range contro l ... .. .. .. .. .. 4 3
High beam ... ... ..... ... .. .. .. .... 45
Low beam .. ............. .... .. .... 43
Rear fog lights ........... .. .. .. .. .. 43
Side marker lights ........ .. .. .. .. .. 43
Turn signa ls .. ..... ...... .. .. .. .. .. 45
Light/rain sensor Headlights . ............. .... .. .. .. 43
Intermittent (windshield wipers) .. .. .. 48
Sensor defective . . . . . . . . . . . . . . . . . . . . 23 Load
ing the roof rack .. .. .. ... ... .. .. . 62
Locking Power loc king switc h ............... . 36
Remote con trol . . . . . . . . . . . . . . . . . . . . 34
U sing the key .. .. ................. . 36
Low beams
. .. .. .... .......... ...... 43
Lower universal anchorages (Canada) 185
Luggage compartment Cargo ne t . . . . . . . . . . . . . . . . . . . . . . . . . 6S
E nlarging . . . . . . . . . . . . . . . . . . . . . . . . . 64
Loading ... .. .... .. . .. .. ..... ... .. . 63
Movement-activated ope ning . ... .. .. . 38
Ski sack ... .. .. .. .. . .............. . 65
Stow ing luggage ..... ............. 132
Tie-downs . . . . . . . . . . . . . . . . . . . . . . . . . 6S
Lumbar support Front seats . . . . . . . . . . . . . . . . . . . . . . . . 54
M
Maintenance . ....... . .. .. ..... ... .. 292
Malfunction Ind icator Lamp (MIL) . . 21, 29
Manua l shift program ... ............. 111
Massage func tio n
F ron t se ats . . . . . . . . . . . . . . . . . . . . . . . . 54
Matte f inish paint clean ing .......... . 209
Mechanica l key .. .. .. . ... ...... ... .. . 32
Mir ro rs
Adjus ting t he ex ter ior mirrors . . . . . . . . . SO
d' . 1mming .. .. .... .. . .. .. ..... ... .. . 51
Vanity mirrors ... .. . ... ...... ... .. . 47
Monito ring the Advanced Airbag System 157
Mult ifunct ion steer ing whee l .......... . 25
mult itron ic (automatic t ransm ission) . .. 107
N
Natu ra l leather
Cleaning
New tires and wheels
NH TSA
Contacting 212
2S7
134
N igh t vision assistant ............ .. .. 103
Cleaning came ra lenses ......... .. .. 210
N itrogen oxide (NOx) catalyt ic converte r
refer to Ad Blue .......... ......... . 218
Number of seats . .. .... ......... .. .. 136
•
•