warning light AUDI S8 2009 Owner's Guide

Opening and closing
• Again, to conserve battery power so that you can start the
vehicle after it has been standing for a long period, the vehicle's
energy management system will switch off any convenience
features not necessary. You will not be able to unlock your vehicle
using the keyless system. •
Applies to vehicles: wi th Conven ience key
Locking the vehicle
You can lock the doors and rear lid without using the
remote control.
Move the selector lever into P.
Fig. 47 Convenience
key: locking the
vehicle
- Press the lock button in the door handle to lock the
vehicle ~& .
You can lock each door on the vehicle. Remember, an authorized key
must be within 5 ft (1.5 meters) of the door.
The selector lever must be in the P position, otherwise the vehicle
will not lock.
& WARNING
• When you lock your vehicle from outside, nobody -especially
children -should remain inside the vehicle. Remember, when you
& WARNING (continued)
lock the vehicle from the outside the windows cannot be opened
from the inside.
• When you leave the vehicle, always remove the ignition key and
take it with you. This will prevent passengers (children, for example) from accidentally being locked in the vehicle should they
accidentally press the power locking switch in the doors.
• Do not leave children inside the vehicle unsupervised. In an
emergency it would be impossible to open the doors from the
outside without the key.
[ i] Tips
It is not possible to open the door immediately after it has been
locked. This is intentional to allow you to check proper locking of all
vehicle doors .•
Anti-theft alarm system
The anti-theft alarm triggers an alarm if anyone attempts
to break into the vehicle.
The anti-theft alarm system triggers an audible alarm and turns on
the emergency flasher if an unauthorized interference with the
vehicle is sensed by the system .
How is the anti-theft alarm system switched on?
The anti-theft alarm system is switched on when you lock the
vehicle. The system is activated approximately 30 seconds after the
vehicle is locked . The indicator lights on top of the driver's and front
passenger's door trim start flashing rapidly for 30 seconds and then
blink slowly. ._

Opening and closing
Switches for front door windows
@ operates the window in the driver's door.
@ operates the window in the front passenger's door.
Switches for rear windows
© operates the left rear window.
@ operates the right rear window .
Safety switch
© Safety switch for rear window operation.
& WARNING
• Do not leave children unattended in the vehicle, especially with
access to vehicle keys. Unsupervised use of the keys can result in
starting of the engine and use of vehicle systems such as power
windows, etc. which could result in serious injury.
• Remember -you can still open or close the power windows for
about ten minutes after the ignition is switched off. Only when
either of the front doors are opened are the power windows
switched off.
• Be careful when closing the windows. Check to see that no one
is in the way, or serious injury could result!
• Always remove the ignition key whenever you leave your
vehicle.
• If you lock your vehicle from the outside, no one, especially chil­
dren, should remain in the vehicle.
• Do not stick anything on the windows or the windshield that
may interfere with the driver's field of vision.
[ i] Tips
• In addition to the switches in the driver's door there is a separate
switch in each door for the power window in that door=>
page 63,
fig.
50 .
• The driver can lower or raise the power side blinds * in the side
windows by using switches © and
@. •
Switches in the driver's door
The driver can operate all windows.
If the respective switch is pushed or pulled the window will
open or close. The power window switches have a
two-posi­
tion function:
Opening the windows
- Push the switch to the first stop and hold it there until the
window has lowered to the desired position.
- Push the switch briefly to the
second stop: the window
will automatically open all the way.
Closing the windows
-Pull the switch up to the first stop and hold it there until
the window has risen to the desired position.
- Pull the switch quickly to the
second position: the
window will automatically close all the way=>
& in
"Controls" on
page 61.
Activating/deactivating rear windows
- Push the switch ®=> page 61, fig. 48 to the depressed
position to activate the rear windows - the light in the
switch will go out.
- Briefly press the switch ® to
deactivate the rear
windows - the switch will return to the safety position
and the light
I will illuminate.

Opening and closing
-In position @, briefly press the control to tilt the roof up
completely.
- To tilt the roof open to any intermediate position press
and hold the switch until the roof reaches the desired
position.
Sliding the roof open
- Turn the switch to position (D to open the roof all the
way.
- Turn the switch to any other position to open the roof to
any intermediate position.
When the glass roof opens, the sun visor, which is designed to ward
off strong sunlight, opens along with it. The visor can be closed
manually when the sunroof is closed.
[ i J Tips
• Be aware that the sunroof may actually be open when the sun
visor is closed. Check and make sure that the sunroof is shut when
parking the car or if it suddenly starts raining.
• If the sunroof is not fully closed but you have pressed and held
the switch for the tilt position, the sunroof will not tilt. •
Closing the power sunroof
Sliding the roof shut
- Turn the rotary switch to position®=> page 65, fig. 53
=> & .
Tilting the roof shut
-Briefly pull the rotary switch to close the roof. -
To tilt the roof down to any intermediate position pull and
hold the switch until the roof reaches the desired posi­
tion.
& WARNING
Improper use of the power sunroof can cause serious personal
injury.
• Be careful when closing the power sunroof. Not paying atten­
tion could cause you or others to be trapped and injured as the
roof closes.
• Always take the key with you when you leave the vehicle to
prevent injuries caused by the roof closing.
• Never leave children or persons requiring assistance alone in
the vehicle, especially when they could access the vehicle keys. Unsupervised use of the keys can result in the engine being
started or use of vehicle systems such as the power windows, etc.
which could result in serious injury. The doors could be locked
with the remote key, delaying help in an emergency.
• The power sunroof will continue to operate until the ignition
key has been removed and one of the front doors has been
opened. •
Power emergency closing
The sunroof can still be closed electrically if for some
reason the overload protection function becomes acti­
vated.
The power sunroof is equipped with an overload protection
feature. If, under normal conditions, the power sunroof will
not close, you can close it using this feature.
- Turn the rotary switch to position ®=>page 65, fig. 53 . .,_

Clear vision
Lights
Switching the headlights on and off ·'t!-·
In the "AUTO " position, a light sensor automatically
s w itches t he head- and tailligh ts on and off in response to
l ight con ditio ns.
Fig . 56 Instrument
p an el: light switch
Switching on automatic headlight control
- T urn th e lig ht switch to AUTO => fig. 56 .
Switching on the side marker lights
- T urn the light switch to ~oo~.
Switching on the headlights and high beam
- T urn th e li ght swit ch to fD.
- Pu sh the high beam leve r forw ard towa rds t he instru -
m ent panel
=> page 73 .
Switching off the lights
- T urn t he light switch to 0 .
Con tro ls and eq uip­
ment
Clear vision
The headlights only work when the ignition is switched on . While
starting the engine or when switching off the ignition, the head ­
lights will go off and only the side marker lights will be on.
After starting the engine, the xenon headlights are automa tically
adjus ted to the load and a ngle of the vehic le (for example, during
acceleration , braking) . This prevents oncoming traffic from exper i­
encing unnecessary headl ig ht g la re from your xenon head ligh ts .
If the system is not operating properly, a warning symbol in the
Auto -Check Contro l is displayed => page
36.
With the side marke r lights or head ligh ts switched on, the sym bol
next to the light switch illuminates
:oo:.
Daytime running lights
• USA models : The daytime running lights wi ll come on automati­
ca lly when the ig nition is turned on and the ligh t swi tch => fig. 56 is
in the
O position or the AUTO position (only in daylight conditions).
The
Daytime running lights func tio n can be tur ned on and off in the
MMI menu
E xterior lighting => page 70 => & .
• Canada models: The dayti me ru nn ing lights wi ll come on au to ­
matically when the ignition is turned on and the light switch
=> fig. 56 is i n the
O po sitio n or the AUTO po siti on (only in dayligh t
condi tions) => & .
Automatic headligh t control
In the switch posi tion AUTO the automatic headlight cont ro l is
t urned on . The low beams are turned on automa tica lly through a
light sensor as soon as ambient brightness (e .g . when driving into a
t unnel) fa lls below a value preset at the factory . When ambient
brightness increases again, the low beams are turned off again
aut omatically =>& .
I n the
AUTO posit io n the low beams are switched off automatically
when the ignition is turned off. If the high beams were switched on,
they w ill come o n again the ne xt time the a utomatic head ligh t
~
Vehicle care I I irechnical data

Clear vision
control is activated. The high beam function must first be switched
on in the MMI
=> page 70 .
Light Se nsor M alfu nction
In the event of a ligh t sensor mal funct ion, the driver is notified in the
instrument cluster display:
~ Autom atic headlights /aut om atic wipers defe ctive
For safety reasons the low beams are turned on permanently wit h
the switch in
AUTO . However, you can continue to turn the lights on
and off using the light switch . Have the light sensor checked as soon
as possible at a dealership.
& WARNING
• Never use d aytime running lights to see where you are going .
The y are not bright enough and will not let you see f ar enoug h
ahead for s afet y, espe cially at du sk or when it is dark. Alw ays
switch on the low beams at du sk or when i t is dark .
• Autom ati c he adli ght s are onl y intended to as sist the dr iver .
The y do not relie ve the d riv er of his re spon sib ility to che ck the
he adlights and to turn them on manuall y according to t he current
ligh t and vi sibility conditions . For example , fog and ra in cannot be
dete cted by the light sen sor s. S o alw ays switch on the he adlights
under these weather con dition s and when dr iving in the dark
gD .
• Cras hes ca n happen when you c annot s ee the ro ad ahe ad and
when you cannot be seen by other motor ists .
- Alw ays turn on the headlight s so that you can see ahe ad and
s o that others can se e your c ar from th e ba ck.
[ i J Tips
• With the switch in AUTO front fog lights and rear fog lights
cannot be turned on in addition. • I
f you remove the ignition from the ignition lock while the head­
l ights are s till on, a bu zzer w ill sound as long as the driver's door is
open to remind you to turn off the l ights .
• Always observe the specific local regulations for your area as to
when to use your lights. •
Adjusting exterior lighting
The functions are set in the MM/.
Press the I CAR] function button.
- Select
Systems in the CA R menu.
Fig. 57 MM I dis pla y:
E xt eri or ligh ting
- Sele ct Exterior lighting. The menu Exterior lighting
appears => fig . 57.
C oming h ome
The Coming home function ensures that after tu rni ng off the igni ­
tion and open ing the driv er's d oor
the vehicle periphery is illum i­
nated in the dark . In addition, the front fog lights, the tail lights and
the license plate light are turned on . On -ti me can be set fo r a per iod
from
O (off) to 60 seconds. ~

ture on the windshield. The rain sensor wiper intervals depend on
t he sensi tivi ty setting as well as vehic le speed . Dur ing brief s tops,
wiper motion wil l adjust in re lation to the amount of rain on the
windsh ield .
During br ief stops, e.g. at a red ligh t, wiper mot ion wil l automa ti­
cal ly be reduced to the next lower speed . Wipers a lready turning at
low speed. cha nge to i ntermittent w ip ing.
When the ignition is turned on, the washer jets are heated .
With the low beam headlights switched on, p ull the wiper lever
towards you only
briefly t o clean the windshield. Ho lding the wiper
lever wou ld a lso engage the headlight washer system each time you
clean the w indsh ie ld and wou ld dra in the washer fluid reservoir
pr ematurely.
& WARNING
• Wiper blades are crucial for safe driving! Only when they are in
good condition are they able to clear the windows properly to
provide uncompromising visibilit y. Worn or damaged wiper blades
are a safety hazard
=> page 82 , "In stalling new wiper blade s"!
• The rain sensor is only designed to assist and support the
driver . It remains entirely the driver' s respon sibility to monitor
out side weather condit ions and to manually acti vate the wipers as
soon as rain or drizzle reduces visibility through the windshield.
• The windshield must not be treated with water-repellent mate­
rial s. They can increa se glare under poor visibility conditions such
as wetness , darkness , or when the sun is low on the horizon. In
addition , they can cau se the wind shield wipers to chatter.
0 Note
In freezi ng or near freezing conditions:
• Always check that the wiper blades are not frozen to the glass
be fore you turn the w ipe rs on. Loose n a wiper b lade wh ich is fro zen
Controls and equip ­
ment
Cl ea r vision
in place before operating the wipers to prevent damage to the wiper
blade or the wiper motor.
• Do not use the wipers to clear a frosted window. Using the
wipers as a convenient ice scraper will des troy the wiper blades .
• Before you take your vehic le to an automatic car wash, make sure
you have the w indshield w iper system switched o ff (lever in p ositi on
Ol, otherwise the windshield wiper system could get damaged in the
car was h if it should suddenly co me on .
[ i ] Tips
• Make sure th e washer fluid reservoir in the engin e compart men t
is topped off before going on a long trip . Look up=>
page 325 for
check ing and fi lling t he washer conta iner.
• I f you switch off the ignition with the windshield wiper lever still
in the inte rval wi pe positio n and t hen come ba ck a while la ter and
drive off, the rain sensor will reactivate itself after the vehicle speed
has exceeded
4 mph (6 km/h) .
• Worn or dirty windshie ld wiper b lades cause smearing which
can aff ect t he opera tion of the rai n senso r. Check the c ondi tion of
your windshield wiper b lades regu lar ly . •
Headlight washer system
The hea dligh t washer s ys tem cle ans the he adlig hts.
Opera te the win dshi eld w iper/was her sy stem @wit h th e
h eadl igh ts t urned o n by ho ld in g the lev er fo r lo nge r than
one s eco nd
~ page 80, fig. 76 .
The washer je ts extend forward out of the fron t bumper driven by
water pressure to spray the front head lights with water .
You should inspect the head lights regu lar ly (for examp le when refu -
e ling) a nd c lean o ff any solid dirt or insects from the lenses. _,.
I • •

Rem oving a wip er blad e
-Bring the windshield wipers to the service position
~ page 82.
-Lift the wiper arm away from t he windshield.
- Pu sh t he locking piece on the wip er blade in the direction
of the arrow @~ page
82, fig. 78. Hold the wiper blade
firmly.
- Remove the wiper b lade @.
Inst alling wiper bl ad e
- Place the new wiper blade in the retainer on the wiper
arm ©~ page
82, fig. 79.
- Pu sh t he locking piece on the wiper blade in the direction
of the arrow@ until you feel it click into place on the
wiper arm .
Clean your wiper blades regularly with a windshield washer solution
to prevent streaking . If the bla des are very dirty, for example with
insects, carefully clean the b lades with a sponge or a soft brush.
I f the wiper b lades begin to s treak the windshie ld, this could be
caused by residue left on the windshield by automatic car washes.
Fill the windshield washer container with a special solution avail ­
able at your authorized Audi deale r to remove the residue .
& WARNING
Be sure to in spect the cond itio n of your wiper blade s regula rly . See
y our authori zed Audi de aler f or repla ceme nt bl ade s.
0 Note
To prevent damage to the wiper system:
Controls and equip ­
ment
Cl ea r vision
• Always loosen blades which are frozen to the windshield before
operat ing wipers.
• Do not use gaso line, kerosene, paint thinner, or other solvents on
or near the wiper blades .
• Do not attempt to move the wipers by hand.
[ i ] Tip s
Commercial hot waxes applied by automatic car washes affect the
c leanabi lity of the windshield .•
Mirrors
Rear view mirror
When the ignition is on, the interior mirror will darken automatically
depending on the amount of light striking the mirror (such as head­
lights shining into the vehic le from the rearl. The mirror will retu rn
to the origina l state (anti -glare off) when you move the manual gear­
shift/gear selector lever into
Reverse or when you turn on the inte ­
rior lights.
[ i ] Tips
The automatic anti-g lare feature on the mirror will not operate prop­
erly if the light shining on the inside mirror is b locked by other
objects. •
I • •

Seats and storage
Seats and storage
General recommendations
Why is your seat adjustment so important?
The safety belts and the airbag system can only provide
maximum protection if the front seats are correctly
adjusted.
There are various ways of adjusting the front seats to provide safe
and comfortable support for the driver and the front passenger.
Adjust your seat properly so that :
• you can easily and quickly reach all the switches and controls in
the instrument panel
• your body is properly supported thus reducing physical stress
and fatigue
• the safety belts and airbag system can offer maximum protec ­
tion =>
page 220.
In the following sections , you will see exactly how you can best
adjust your seats.
There are special regulations and instructions for installing a child seat on the front passenger's seat. Always follow the information
regarding child safety provided in=>
page 245, "Child Safety".
L1}. WARNING
Incorrect seating position of the driver and all other passengers
can result in serious personal injury.
• Always keep your feet on the floor when the vehicle is in motion
- never put your feet on top of the instrument panel, out of the
window or on top of the seat cushion. This applies especially to
the passengers. If your seating position is incorrect, you increase
the risk of injury in the case of sudden braking or an accident. If
& WARNING (continued)
the airbag inflates and the seating position is incorrect, this could
result in personal injury or even death.
• It is important for both the driver and front passenger to keep
a distance of at least 10 inches (25 cm) between themselves and
the steering wheel and/or instrument panel. If you're sitting any closer than this, the airbag system cannot protect you properly. In
addition, the front seats and head restraints must be adjusted to
your body height so that they can give you maximum protection.
• Always try to keep as much distance as possible between your­
self and the steering wheel or instrument panel.
• Do not adjust the driver's or front passenger's seat while the
vehicle is moving. Your seat may move unexpectedly, causing
sudden loss of vehicle control and personal injury.
If you adjust
your seat while the vehicle is moving, you are out of position. •
Driver's seat
The correct seat position is important for safe and relaxed
driving.
We recommend that you adjust the driver's seat in the
following manner:
- Adjust the seat in fore and aft direction so that you can
easily push the pedals to the floor while keeping your
knees slightly bent=>
& in "Why is your seat adjustment
so important?".
Adjust the seatback so that when you sit with your back
against the seatback, you can still grasp the top of the
steering wheel. _..

________________________________________________ S_e_ a_ ts_ a_ n_d _ s_t _o _r_ a ....; g::;. e _ __._
through the passenger compartment can cause in a collision at a
speed considered relatively low.
& WARNING
Weak, damaged or improper straps used to secure items to tie ­
downs can fail during hard braking or in a collision and cause
serious personal injury.
• Always use suitable retaining straps and properly secure items
to the tie-downs in the luggage compartment to help prevent
items from shifting or flying forward.
• Never attach a child seat tether strap to a tie-down .•
Elastic cargo net
The cargo net prevents light objects from sliding around
in the luggage compartment.
Con tro ls and eq uip­
ment
Fig . 105 Luggage
compartment cargo
net Fig
. 106 Luggage
compartment cargo
net attached to
mounting hooks
Securing objects to the luggage compartment
floor with the net
- Lay out the cargo net in the luggage compartment.
Engage all four hooks into the fastening eyelets
=> fig. 105.
- Place objects to be secured under the net .
Configuring the net to restrain small objects
-Lay out the cargo net in the luggage compartment.
Engage all four hooks into the fastening eyelets
=> fig. 105.
- Pull down the mounting hooks@ located below the base
of the rear window.
- Connect each loop on the net to the corresponding hook
as illustrated
=> fig. 106.
- Place items inside the net.
Mounting hooks
There are two mounting hooks under the base of the rear window
inside the luggage compartment. You can attach the cargo net as
well as
light objects to these hooks. ..,_
Vehicle care I I irechnical data

• ..__S_ e_ a_t _s _ a_n _d_ s_ t_ o _ r_ a_ g=- e ______________________________________________ _
The mounting hooks are spring-loaded and will return to their
normal position when not in use.
& WARNING
For strength-related reasons, the mounting hooks can only be
used to secure objects weighing up to 10 lb .
15 kgl. Heavier objects
will not be adequately secured -there is a risk of injury. •
Applies to vehi cles : wi th sk i sa ck
Ski sack
Use the ski sack to transport and protect skis and other
long, light items in the passenger compartment.
O •----0
Fig . 107 Luggage
compartment ski sack
hatch
Fig . 108 Ski sack:
securing
Load the ski sack from the luggage compartment.
Loading
- Open the luggage compartment lid and clear a space in
the center.
- Press the release button for the ski sack hatch in the
luggage compartment and pull down the hatch
~ fig. 107.
- Fold out center armrest in the rear seat backrest.
- Press the release button on the lid from inside the
vehicle, and then lower the lid.
- Pull out and unfold the ski sack.
- Load skis or similar objects through the luggage
compartment into the interior of the vehicle~& .
Securing
- Insert the ski sack strap@~ fig. 108 in the center buckle
®·
- Pull the safety belt taut on the free end of the belt@.
Securing in vehicles with power individual rear
seats*
Loop the ski sack safety belt around the center arm rest.
- Pull the safety belt taut on the free end of the belt .
Stowing
- In the luggage compartment, close the ski sack hatch.
- Fold the ski sack carefully and stow away.
- Close and engage the inner hatch.