lights AUDI S8 2014 Owner's Manual

28 Instruments and warning/indicator lights
The date and time are shown in the instru­
ment cluster d isplay
c:;, page 24, fig. 4. There
is also an ana log clock in the center console
c:;, fig. 12.
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds . When the ign ition is switched
on, the time is always displayed in the status
line © regardless of the current display.
You can set the time on both clocks and the date display in the MMI. Refer to the MMI
owner's manual for instructions.
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 13 Inst rume nt cluster: Serv ice inte rval d isp lay
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition on
c:;, fig. 13 .
After about S seconds the display switches back to normal. The distance and time re­
maining are updated each time the ignition is
switched on until the date due for service is
reached .
Service due
When the due date for service is reached, the
message
Service due! appears in the instru­
ment cluster immediately after you switch the
ignition on . Additionally, a warn ing tone sounds. After about 5 seconds the disp
lay
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > Car sys­
tems
control button > Servicing & checks >
Service interval displays.
Resetting the service interval display
Your authorized Audi dealer will reset the cor­
responding service schedule after performing
the appropr iate service on your vehicle. You
also have the possibility to reset the oil
change schedule after hav ing performed an
o il change according to Aud i specif ications.
Select the
I CAR I function button > Car sys­
tems
control button > Servicing & checks >
Service Intervals > Reset oil change interval.
(D Note
If you disconnect the battery term inals, no
calculations can be made for the service
i nterval disp lay during th is time and no
serv ice reminder will appear. Remember
that observing the proper service intervals
i s vitally important to extending the life of
your vehicle, pa rticularly the engine, and
maintaining its value. Even if the mileage
driven is low, the maximum period of one
year from one service to the next must not
be exceeded.
(I} Tips
-Do not reset the display between oil
changes, otherwise the disp lay w ill be in­
correct.
- The information in the Service Reminder
remains stored
even when the vehicle
battery is disconnected .

Instrument s and warning /indicator lights
Open door/hood/rear lid warning
Fig. 14 D isplay: doors and rear lid open
With the ignition switched on, the warning il­
luminates when at least
one door or the hood
or the rear lid is not closed. The symbol also
shows you
which door(s) or lid is not closed.
In the illustration ¢
fig. 14 it is the driver's
door and the left rear door.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢4 in
the instrument cluster is part of the On-Board Diagnostic (OBD II) system.
The warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized.
This indicates that the MIL is work ing proper­
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv­
ing, a malfunction may ex ist in the engine sys­
tem. If the light illuminates, the catalytic con­
verter could be damaged.
Continue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erat ions) and have the condition corrected.
Contact your author ized Audi dealer.
If the light illuminates, the electronic speed limiter may also be malfunctioning. For more
in formation ¢
page 30, Electronic speed
limiter.
An improperly closed fuel filler cap may a lso
cause the MIL light to illuminate¢
page 225.
On-Board Diagnostics
Fig. 15 Location of Data Link Connector (DLC)
On-Board Diagnostics monitors the compo­
nents of your emission control system. Each
monitored component in your engine system
has been assigned a code . In case of a mal­
funct ion, the component will be identified
and the fault stored as a code in the control
module memory.
The MIL light may also illuminate if there is a leak in the on -board fuel vapor recovery sys­
tem.
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed ¢
page 225.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe­
cial diagnostic equipment (generic scan tool
for OBD).
In order to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC). The DLC is located to the
right of the hood release
¢fig. 15.
Your authorized Audi dealer or a qualified
service station can interpret the code and per­
form the necessary repair.
A WARNING
Do not use the diagnost ic connector for
personal use. Incorrect usage can cause
malfunctions, wh ich can increase the risk
of a collision!
-
29

30 Instruments and warning /indicator lights
Electronic speed limiter
Your veh icle may be factory equ ipped with
tires that are rated for a maximum speed of
130 mph (210 km/h). This is less than the
maximum speed of your vehicle. To reduce the
risk of sudden tire failure and loss of control if
the vehicle is operated at excessive speeds,
your vehicle also has an electronic speed limit­
er. The electronic speed limiter prevents your
vehicle from going faster than the tire speed rating. For more informat ion
c::> page 259.
If the engine control unit receives faulty vehi­
cle road speed signals, the Malfunction Indi­
cator Lamp (MIU¢• will illuminate . If this
occurs, contact the nearest authorized Aud i
dealer for assistance.
58
Your vehicle's top speed is electronically limit­
ed to 155 mph (250 km/h).
If the engine control unit receives faulty vehi ­
cle roadspeed signals, the Ma lfunction Indica­
tor Lamp (MIU ¢.id will illuminate. If this oc­
curs, contact the nearest authorized Audi
dealer for assistance.
A WARNING
-
Always observe the posted speed limits
and adjust your speed to suit prevailing
road, traffic and weather conditions. Never
drive your vehicle faster than the maxi­
mum speed rating of the tires installed.

42 Opening and closing
Closing the windows
.,. Pull the switch to the first stop and hold it
until the window reaches the desired posi­
tion .
.,. Pull the switch briefly to the
second stop to
automatically close the window.
Power window switches
@ Driver's door
@ Passenger's door
© Left rear door
@ Right rear door
® Safety button (or two safety buttons in
vehicles w ith power child safety locks
c:> page 41)
Child safety lock
When the safety button® c:> fig. 32 is press­
ed, the LED in the button lights up. The fol­
lowing features are switched off:
- The power windows in the rear doors,
- The buttons for the power sun shades * in
the side windows,
- The buttons for the power sun shade* in the
rear window,
- Front passenger power seat adjustment*
button.
&_ WARNING
- When you leave your veh icle - even if on­
ly brief ly - always take the ignition key
with you. This applies particularly when children remain in the veh icle. Otherwise
the chi ldren could start the engine or op­
erate electrical equipment (e.g. power
w indows). The power windows are func­
tional until the driver's door or passeng­
er's door has been opened .
- Be careful when closing the windows.
C heck to see that no one is in the way, or
serious injury could result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the
windows can no longer be opened in an
emergency.
(D Tips
- The driver can lower or raise the power
sun shades* in the s ide windows by using
switches © and @.
- After the ignition has been switched
off,
the windows can sti ll be opened or
closed for about 10 minutes. The power
w indows are not switched off until the
dr iver's door or passenger's door has
been opened .
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected .
.,. Pull and hold the power window switch until
the window is fully closed .
.,. Release the sw itch and then pull it again for
at least one second.
Valet parking
The valet parking feature protects the lug­
gage compartment from unauthorized ac­
cess .
Fig. 33 Valet parking button
With "valet parking" activated , the luggage
compartment lid cannot be opened .
.,. Remove the mechanica l key
¢ page 32.
.,. Open the glove compartment and activate
c:> fig. 33 the "valet parking" feature by
pressing the
j VA LETi button . The indicator
light in the sw itch illuminates .
.,. Close the glove compartment and lock it
w ith the mechanical key . .,.

46 Clear vis ion
Clear vision
Lights
Switching the headlights on and off
Fig . 37 Instr ument pane l: lig ht sw itc h wit h all -weath­
er lig hts *
The headlights only wo rk when the ignition is
sw itched on. Wh ile start ing the eng ine or
when switching off the ig nition, the head­
lights will go off and on ly the s ide marker
lights w ill be on .
I f the system is not operating properly, a
warn ing symbol in the dr iver inform ation dis­
p lay is displayed <=> page
22 .
Light switch -'t/., -
Tu rn the switch <=>fig. 37to the co rrespond ing
position . When the lights a re switched o n, the
:o o; symbo l tur ns on .
0 -The lights are off or the dayt ime run ning
lights are on:
- USA models: The daytime running ligh ts
will come on automatically when the igni­
t ion is on a nd the light switch <=> fig .
3 7 is in
the
O pos it ion or the AUTO position (only in
daylight cond itions) . T he Daytime running
lights function can be tu rned on and off in
the MMI <=> page
48, <=> .& .
- Canada model s: T he daytime running lig hts
will come on au toma tically when the igni ­
t ion is on and the light switch<=> fig . 37 is in
the
O posit io n, the :oo~ position or the AUTO
posit ion (on ly in daylight conditions)<=>.& .
AUTO -Automatic headlights swi tch on an d
off depend ing o n brightness , fo r example in
tw ilight, during rain or in tunnels<=>.& .
:oo~ -Side marker lights
io -Low beam head lights
[!QJ . Fog lights* (vehicles with Xenon p lus
headlig hts*)
~ -All-weathe r lights* (vehicles with LED
headlig hts*)<=> fig. 37
[2[1-Rear fog lights* . When the rear fog lights
are on, the symbol
0$ on the sw itch will illu­
minate .
All-weathe r lights*
In veh icles with all -wea ther lights, the front
li ghts are adj usted automat ically so that you
are less like ly to see glare from your own
headlights , for example when driving on a wet
road.
Automatic dynamic headlight range
control*
Your vehicle is equipp ed with a headlight
range control system so that the head lights
do no t blind oncoming traff ic if the vehicle
load cha nges . The headlight range a lso ad­
justs automa tically when braking and acceler­
at ing .
Light funct ions
The following light funct ions are availab le de­
pending on veh icle equipmen t and o nly func­
t ion when the lig ht switch is i n the AUTO posi ­
t io n. You can deactivate these functions in the
MM I und er Audi adaptive light <=>page
48 .
Static cornering light * (vehicles with LED
headlights or adaptive light) -the corner ing
light sw itches on automat ical ly when the
stee ring wheel is turned at a ce rtain angle at
speeds up to approxima tely 4 4 mph ( 70 km/
h) and when the turn signal is act ivate d at
speeds up to approximately 25 m ph ( 40 km/
h) . The area to the side of the vehicle is illumi­
nated bette r when turn ing.
Dynamic curve light * (vehicles with adap tive
li gh t) - the curve light on ly functions at
speeds betwee n approximate ly 6 mph (10
km/h) and 68 mph (110 km/h) and adapts it-
self to the curves in the road . .,.

Highway light function* (vehicles with LED
headlights) - this function adapts the lighting
for highway driving based on vehicle speed.
.&_ WARNING
-Automatic headlights are only intended
to assist the driver. They do not relieve
the driver of his responsibility to check
the headlights and to turn them on man­ ually according to the current light and
visibility conditions. For example, fog
cannot be detected by the light sensors.
So always switch on the headlights
~D
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see the road ahead and when you cannot be
seen by other motorists. Always turn on
the headlights so that you can see ahead and so that others can see your car from
the back.
- Please observe legal regulations when
using the lighting systems described.
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
(D Tips
- The light sensor* for automatic dynamic
headlight range control* is located in the
rear view mirror mount. You should
therefore not apply any stickers to the
windshield in this area in order to pre­
vent malfunctions or failures.
- In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display~
page 22.
- You will hear a warning tone if you open
the driver door when the exterior lights
are switched on.
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after Clear vision 4
7
switching them on. This does not affect
the service life of the lighting.
Emergency flasher
Th e emergency flasher makes other motorists
oware that you or your vehicle are in on emer­
gency situation.
'1'.r-- ~·
~ ·--~. -~ -..... -._.. l'
1
Fig. 38 Center console: emergency flasher switc h
.,. Press the switch ~ 9 fig. 38 to turn the
emergency flashers on or off .
When the emergency flasher is on, all four
turn signals blink at the same time. The turn
signal indicator lights
H Iii in the instrument
cluster, as well as the light in the emergency
flasher switch~ blink likewise. The emergen­
cy flasher also works when the ignition is
turned
off.
The emergency flashers will turn on automati­
cally if you are in an accident where the airbag
has deployed.
@ Tips
You should turn on the emergency flashers
when:
-you are the last vehicle standing in a traf­
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
-your vehicle is being towed by a tow truck or if you are towing another vehicle behind you.

48 Clear vision
Adjusting the exterior lighting
The settings are adjusted in the MMI.
• Se lect : I CAR ! function button > Car systems
control button > Vehicle settings > Exterior
lighting .
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights activation time -You can adjust if
the head lights switch on
Early, Med. or Late
according to the sensitivity of the light sensor .
Audi adaptive light * -You ca n sw itch adaptive
l ight
On and Off.
Automatic high beams*
You can switch the high beam ass ist on and
off .
Daytime running lights
USA models :
You can switch the dayt ime run­
ning lights
on and off .
Canada models:
The function cannot be
turned off .
It is activated a utomat ica lly each
time the ign ition is switched on. This menu
item is shown "greyed out".
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when yo u switch the
ignition off and open the driver's door. To turn
the function on, select
Lights when leaving
car > On .
The leaving home function illuminates the
area outside the vehicle when you un lock the
ve hicle. To turn the funct ion on, select
Lights
when unlocking car > On .
The coming home and leaving home functions
only operate when it is dark and the light
switch is in the
AUTO position.
Turn signal and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
Fig. 39 Tu rn signal and high beam lever
The turn signa l and high beam lever has the
following functions:
Turn signals ¢ 9 (D@
• Push the lever up as far as it can go to turn
on the right turn signal or down to turn on
t he left turn signal¢
fig. 39.
N 0 ... 'i' :r
~
• Move the lever briefly unti l you meet res ist·
ance and re lease it to flash three times.
• Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam [D @
• Push the lever forward to switch on the high
beam (vehicles with high beam assist*
¢ page49).
• Pull the lever back towards you to switch off
the high beam .
Headlight flasher [D ©
• Pull the lever toward the steering wheel to
use the headlight flasher.
Notes on these features
- The turn signals only work w ith the ignition
switched on. The indicator lights
II or Bin
the instrument cluster¢ page 11 also blink.
- After you have turned a corner, the turn sig-
na l switches off automatically.
- The
high beam works only when the head-
lights are on . The indicator light
II in the ..,.

instrument cluste r ill uminates when the
high beams are on.
- T he
headlight flasher works only as long as
you hold the lever -even if there are no
li ghts turned o n. The indicator light
El in
the instr ument cluster illuminates when you
use the head light flasher.
A WARNING
Do not use the hig h beam or headlight
flasher if you know that these could blind
oncoming traffic.
High beam assist
Applies to vehicles: with high beam ass ist
The high beam assist automatically switches
the high beams on or off, depending on the
surroundings and traffic conditions .
Fig. 40 Turn sig na l and high beam lever: Turning on
and off the high beam ass ist
Activating h igh beam a ssi st
8 .... 0 :i: ;g
Requirement: The light sw itch must be in the
AUTO position, the low beam head lights must
be on and the high beam assist must be
switched on in the Infotainment¢
page 48.
~ Press the lever into position @ in order to
activate the high beam assist. T he indicator
light
Ill turns on in the instrument cluster
display and the high beams switch o n or off
automatically . The indicato r light
II turns
on if the high beams w ere switched on .
Switching the high beams on /off
manually
Requirement: Hig h beam ass ist is activated.
Clear vis ion 49
If the high beams d id not swi tch on/off auto ­
matically when expected, you may instead
switch them on/off manua lly:
~ To swi tch the high beams on manually, press
the lever into position@. The indicator light
II turns on. To switch the hig h beams off
aga in, p ull the leve r into position @.
~ To switch the high beams off manually after
they have turned on a utomat ica lly, pull the
lever i nto pos ition @.
Oper ating the headlight fla sher
~ To operate the flashe rs while the high beam
assist is act ive, pu ll the lever into position
@ . T he high beam assist will remain act ive.
Messag es in the instrument cluster
di spl ay
Headlight assist: System fault
Drive to your authorized A udi dealer immed i­
ate ly to have the ma lfunction corrected. Yo u
can still switch the high beams on or off man­
u ally.
Headlight a ssi st: Unavailable . No camera
view
T he came ra v iew is b locked, for example by a
sticker o r debr is.
The sensor is loca ted be tween the inter io r
r earvi ew mirror and the w indshield . There­
fo re, do no t place any st ic kers in this a rea on
th e windsh ie ld .
Service setting
There is a d ifferent sens it ivity sett ing for serv­
ic ing . Th is sett ing can be activated by pr essing
and hold ing the b utton on the int erio r r ear­
view m irror for mo re tha n 1 8 seconds. The
L E D next to the button blinks th ree times.
If
yo u have accidentally se lec ted this service
funct io n, the origi nal sensitivity will be a uto­
matically restored the next t ime yo u sw itch
the ignit ion on.

50 Clear vis ion
& WARNING
H igh beam assist is only intended to assist
the driver. The driver is still responsible for controlling the headlights and sw itching
th e high beams on and off manually de­
pending on traffic, l ighting and visibility
condi tions. Failure to intervene manually
may lead to ris k of accident . It may be nec­
essary to operate the high beams man ua l­
ly in the following situat ions, e.g .:
- For adverse weather conditions such as
fog, heavy rain, blowing snow or spraying
water .
- On roads where oncoming traffic may be
partia lly obsc ured such as expressways .
-If there are individuals on the road with
no light ing or poor lighting, such as cy ­
cl ists .
- In tight c urves and on steep s lopes .
- In poorly lit areas.
- With strong reflectors su ch as signs.
- If the area of the windshie ld nea r th e
sensor is fogged over, dirty, icy or cov­
ered w ith a st icker.
(D Tips
- The high beam ass ist is active above a
speed of approx . 25 mph (40 km/h).
- If afte r activation, your speed falls below
approx . 15 mp h (24 km/h), the high
beams w ill automatically be switched
off.
Interior lights
Front and rear interior lighting
Fi g. 41 Headliner: Front interior lights
F ig. 42 Rear headli ner : Read ing light
Press the app ropriate button ~ fig . 41:
~ -Inter ior light ing on/off
l!l -Door contact switch. The interior lighting
turns on automatically when you u nlock the
vehicle, open a door or switch the ignition off.
The interior light ing turns off several seconds
after you close the doors, when you lock the
vehicle or when you switch the ignition on.
When a doo r is open, the light turns off after
a few min utes.
~ -Read ing lights on/off
~ - Switching the rear reading lights on/off
from the cockpit .
I REAR MODEi* -Switching the rear readi ng
li ghts on/off from the cockpit : press the
I REAR MODE ! button and then th e appropriate
button ~ in the cockpit.
Ambience lighting
Applies to veh icles: w it h amb ience l ig h ting
You can select a color profile and brightness
for the ambie nce lighting in various areas of
the ve hicle, called zones.
Turning ambience lighting on
.. Select in the MMI: ICAR ! function button >
Car systems control button > Vehicle set·
tings > Interior light ing > On .
Adjusting /turning off the brightness
• Sele ct in the MM I: ICARI fu nction button >
Car sy stems control b utton > V ehicle set­
ting s> Inte rior light ing > Brightness .

.. Turn the knob to the desired vehicle area
and press the knob . The bar that appears in­
dicates the selected brightness.
.. To increase or reduce the brightness, turn
the knob and press it.
Se lecting a color profile*
.. Se lect in the MMI: !CAR ! function b utton >
Ca r sys tems control button > Vehi cle se t­
tings
> In terior light ing > Colo r profile .
The amb ience lighti ng turns on when the
function is activated in the MMI and when you
turn the headlights on whi le the ignition is
switched on.
Adjusting the b rightness
You can ad just the brightness for the four
zones
F ront top , Fr ont f ootwell , Rear top and
Rear footwell o r for All area s at the same
time.
Selecting a color pr ofile
You ca n select from the Ivory , Polar and Ru ­
b y/ Polar
color profiles .
(I) Tips
The settings are automati cally sto red and
a ssigne d to the remote con tro l key that is
in use.
Instrument illumination
You can adjust the brightness of the instru­
ment and display illumina tion.
F ig. 43 In strument ill um ination
.. Press the knob to release it .
.,. Turn the knob toward"-" or"+" to reduce or
i ncrease the brightness .
Clear vision 51
.. Press the knob again to return it to its origi ­
na l position .
(D Tips
The instrumen t illum ina tion (for d ials an d
needles) lights o n when the ignition is
switched on and the vehicle lights are
turned off. As the daylight fades, the illu­ mination of the dials likewise d ims auto­
matically and wi ll go out completely when
the outs ide light is very low. Th is feature is
meant to rem ind you to sw itch on the
headlights whe n outs ide ligh t conditions
be come poo r.
Vision
Sun visors
E ]
-
F ig . 44 Sun visor
The sun visors fo r the driver and passenger
can be re leased from their brackets and
turned toward the doo rs
c:> fig . 44 @. They
can also be moved back and forth lengthwise
in this position.
The m irror light switches on when the cover
over the vanity mirror @opens .
T he re is a shade be twee n the dr iver's and pas­
senger 's s un v isors that can be used to cover
the gap above the rearview mirro r.