ECO mode AUDI S8 2015 User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2015, Model line: S8, Model: AUDI S8 2015Pages: 312, PDF Size: 79.18 MB
Page 71 of 312

-Turn the electrical equipment off if the
socket has sw itched off because of overÂ
heating.
(D Note
- Always fo llow the manufacturer's inÂ
structions for all electrical accessories
you want to use with the electrical sockÂ
et!
- Do not connect lamps that contain a neÂ
on tube. For technical reasons the lamp may be damaged.
- Do not connect any 230-volt equipment
to the 115-volt socket . The equipment
may be damaged . If necessary, check the
permissible voltage for the equipment
on the model label.
- In the case of some power packs, e .g . for
a laptop computer, the bu ilt-in overcurÂ
rent shutoff prevents it from be ing
switched o n because of excessive startÂ
u p current. In this case, disconnect the
power pack from the consumer and re Â
connect it after about 10 seconds.
@ Tips
- Unsh ielded equipment may cause interÂ
ference in the radio and the veh icle elecÂ
tronics.
- Some eq uipment may work p roperly beÂ
cause of the reduced power (wattage),
available from the socket.
S ea ts a nd s to rage 69
Folding table in the center console
Applies to vehicles: with fo lding table in the center conÂ
sole
The folding table is stored in the front ar ea of
the center console.
Fig. 69 Rea r ce nte r con sole : ope ning the fo lding table
Fig. 70 Rea r ce nte r con sole: fo ld ing table i nclined poÂ
s it ion
O pening
.,. Pull the handle @back ¢ fig. 69. The foldÂ
ing table extends o ut pa rtially by itself
¢ .&_ .
.. Pull the folding table up unti l it locks into
place @ .
.. Fold the tabletop back and down
@ .
Storing
.. Release the tabletop @to fold it back .
.. You can now move the folding table vert icalÂ
ly back into its original position.
A WARNING
- Do not open the folding tab le while drivÂ
ing. Opening the folding table while drivÂ
ing increases the risk of injury in the
event of a collis ion or sudden b rak ing .
- To reduce the risk of pinching, open and
close the folding table carefully and in a
controlled manner .
Page 74 of 312

7 2 Seats and storage
-For safety reasons, do not transport
more than two pairs of skis in the ski
sack.
- You must secure the ski sack with the
strap after loading.
- Make sure all objects that you are transÂ
porting in the pass-through are secured.
Otherwise they could slide around during
sudden braking maneuvers and cause inÂ
jury.
Q) Tips
- Never stow the ski sack away when it is
still wet or damp (for example, snow
melting from skis). Allow it to dry comÂ
pletely before stowing it away .
- Position skis in the ski sack with the
pointed ends facing the front and ski
poles with the pointed ends facing the
rear.
Roof rack
Description and mounting locations
Additional cargo can be carried with a roof
luggage rack.
Fig. 77 Roof rack attac hment points
,. Always read and follow the instructions proÂ
vided by the roof rack manufacturer when
installing the roof rack system .
If luggage or cargo is to be carried on the
roof, you must observe the following:
- To enhance the vehicle's streamlined design,
rain gutters have been molded into the roof.
It is not possible to use normal roof racks.
Only install a roof rack specifically designed for your model AB. Contact the nearest Audi
dealer for information on approved modular
roof racks for your vehicle.
- Only use roof racks approved for your vehiÂ
cle. These approved roof racks are the basis
for a complete roof rack system. Additional
attachments or carrier systems are needed
to transport luggage and sports equipment.
We recommend using roof racks from the
Audi original accessories program .
- When installing the roof rack, make sure it
is only mounted on the designated locations
on the roof~
fig. 77 .
- We recommend that you keep the installaÂ
tion instructions for your roof rack system
together with your Owner's literature in the
vehicle .
When should the roof rack be removed?
-Before going through an automatic car wash
(it is best to ask the car wash operator for
advice)
- When not in use, to reduce fuel consumpÂ
tion, wind noise and to guard against theft .
8,. WARNING
-Use of an unapproved roof rack or incorÂ
rect mounting of an approved roof rack
can cause the roof rack or the items atÂ
tached to it to fall off the roof onto the
road.
- Objects falling from the roof of a vehicle
can cause a crash and personal injury.
- Only mount the roof rack on the desigÂ
nated locations on the roof¢
fig. 77.
- The roof rack system must be installed
exactly according to the instructions proÂ
vided.
- When driving with a roof rack system,
changes to the center of gravity and wind
resistance can change the vehicle hanÂ
dling and lead to a collision. Always
adapt your driving and your speed to the
current conditions.
-
Page 77 of 312

Front cupholder
• To open the cupholder, tap the cover
¢ fig. 80, ¢ _&.
Rear cupholder
• To open the cupholder, tap the front strip
¢fig. 81, ¢ _&.
In vehicles with a full-length center console in
the rear, the cupholder is located at@
¢ page 68, fig . 68.
_& WARNING
Spilled hot liquid can cause an accident
and personal injur y.
- Never carry any beverage containe rs with
hot liquids, such as hot coffee or hot tea,
in the vehicle while it is moving . In case
of an accident, sudden braking or other
vehicle movement, hot liqu id could spill,
caus ing scald ing burns . Spill ed hot liquid
can also cause an accident and personal
injury.
- Use only soft cups in the cupholder. Hard
cups and glasses can cause injury in an
acc ident.
(D Note
On ly drink containers with lids should be
carried in the cupho lder. Liquid could spill
out and damage your veh icle's electronic
equ ipment or sta in the upholstery, etc.
Cooled glove compartment
The cooled glove compartment only functions
when the A/C system is switched on.
Fig. 82 Glove compa rtment: switc hing cooling mode
on/off
Seats and storage 75
• Turn the knob @counterclockwise to switch
cooling on. The symbols on the knob indiÂ
cate the correct pos ition
<=> fig. 82.
• Turn the knob@clockwise to switch cooling
off.
The glove compartment cooling mode only
functions when the vehicle A/C system is
switc hed on. If the heating is switched on,
switc hing the glove compartment cooling
mode off is recommended .
_& WARNING
Always leave the lid on the glove compartÂ
ment cover closed while dr iving to reduce
the risk of injury.
© Tips
The glove compartment can be locked usÂ
in g the mechanical key
¢page 32.
Additional storage
There are a var iety of storage compartmen ts
and fasteners in various places in the veh icle.
- Storage compartments in the doo rs
- Net in the front passenger footwell
- Eyeglasses compartment in the headliner
(near the rearview mirror)
- Storage compartments under the center
armrests
- Compartments* on the back of the front
seat backrests
- Garment hooks over the rear doors
- Compartment in the center console with
pass-through)* (rear)
- Compartment behind the rear center armÂ
rest (in vehicles without the pass-through*
or cooler *)
- Cell phone holder* in the right rear door
- Bag hoo ks in the luggage compartment
_& WARNING
-=
-When driving, do not leave any hard ob-
jects on the rear w indow shelf or allow
your pet to sit on the she lf . They cou ld
Page 80 of 312

78 Warm and cold
Warm and cold Climate controls
Description
The climate control system warms, cools and
adds humidity to the air in the vehicle interior.
It is the most effect ive when the windows and
sunroof* are closed . If the temperature inside
the parked vehicle becomes very warm, open ing the window briefly will speed up the coolÂ
ing process.
I n all heating mode functions except
defrost,
the blower on ly switches to a higher speed
once the engine coolant has reached a certain
temperature.
Condensation from the cooling system can
drip and form a puddle of water under the veÂ
hicle. This is normal and does not mean there
is a leak.
Pollutant filter
The pol lutant filter removes pollutants such
as dust and pollen from the air.
The air pollutants filter must be changed at
the intervals spec ified in you r Warranty
&
Maintenance booklet, so that the air condiÂ
tioner can properly work.
I f you drive your vehicle in an a rea with high
a ir po llution, the fi lter may need to be
changed more frequent ly than specified in
your Aud i Warranty
& Maintenance booklet. If
in doubt, ask your authorized Audi Service AdÂ
visor for advice .
Key coded settings
The climate control settings are a utomat ically
stored and assigned to the remote control key
that is in use.
A WARNING
Reduced visibility is dangerous and can
cause accidents. -
- For safe driving it is very important that
all windows be free of ice, snow and conÂ
densation.
- Comp letely familiarize yourself with the
proper use and funct ion of the heat ing
and ventilation system and especially how to defog and defrost the windows.
- Never use the windshield wiper/washer
system in freez ing weather unt il you
have warmed the windshield first, using
the heating and ventilation system. The
washer solution may freeze on the wind sh ie ld and reduce visib ility.
(D Note
- If you suspect that the air conditioner has been damaged, switch the system
off to avoid further damage and have it
inspected by a qualified dealership.
- Repairs to the Audi air conditioner reÂ
quire special technical know ledge and
special tools. Contact an authorized Aud i
dea ler fo r assistance.
@ For the sake of the environment
By reducing the amount of fuel you use,
you also reduce the amount of pollutants
emitted into the air.
(D Tips
- Keep the air intake s lots (in fro nt of the
w indshield) free from ice, snow and de Â
bris in order to maintain the proper funcÂ
tion of the climate control system.
- T he energy management system may
switch the seat heating* or rear window
defroster off temporari Ly . These systems
are available again as soon as the energy
balance has been restored.
- Air escapes through vents under the rear
window. When placing items of clothing
on the luggage compartment cover, enÂ
sure that the openings are not covered.
Page 81 of 312

.... N .... N
0 J:
"". .... I.O
"' ....
"' ....
Warm and cold 79
Operation
We recommend pressing the
I AUTO I button and setting the temperature to 72 °F (22 °C) .
Fig. 84 Cockpit controls
Fig. 85 fou r zone auto matic cli mate control: rear conÂ
trols
Press the buttons to turn the functions on or
off . Use the dials to adj ust the temperature,
the blower speed and the a ir distribution. The
LED in a button w ill light up when the funcÂ
tion is sw itched on. The settings are shown in
the climate control display and are a lso shown
in the MMI display for a few seconds. The drivÂ
e r and front passenger sett ings can be adj ustÂ
in g separately.
You can also adjust the rear left and right
sides in the four zone automat ic climate conÂ
trol*
~ fig . 85 .
IOFF I Switching the climate control
system on/off
The IOFFI button switches the climate control
system on or off .
It also switches on when you
turn the dial or press any button . Airflow from outside is
blocked when the climate control
system is switched off.
You can acti vate the residual heat functi on
whe n the ignition is off by pressing and holdÂ
ing the ~ button . The residual heat from the
coolant is used to heat the vehicle i nterior.
The residua l heat function switches off autoÂ
matically after about 30 minutes.
IAIC ! Switching cooling mode on/off
The air is not coo led and hum idity is not reÂ
moved when cooling mode is switched off.
This can cause fog on the windows. Cooling
mode switches off automatically when the
outside temperature is be low zero.
1- 1 Switching recirculation mode on/off
In recircu lation mode, the air inside the vehiÂ
cle is circulated and filtered. This prevents the
unfiltered air outside the vehicle from enterÂ
ing the vehicle interior. We recommend
switching recirculation mode on when driving
through a tunnel or when sitting in traffic
¢ ,&. .
The
! AUTO I button or~ button switches reci rÂ
cu lation mode off .
IAUTO! Switching automatic mode on
Automatic mode maintains a cons tant temÂ
perature inside the vehicle. Air temperature,
~
Page 82 of 312

80 Warm and cold
airflow and air distribution a re controlled auÂ
tomatically.
Adjusting the temperature
Temperatures between 60 °F (+16 °() and
84
°F (+28 °C) can be set. Outside of this
r ange,
lo or hi wi ll appear in the climate conÂ
trol system disp lay. At both of these settings,
the climate control system runs continuously
at maximum cooling or heating power. There
is no temperature regulation.
~ Adjusting the airflow
You can adjust the airflow manually to suit
your needs . To have the airf low regulated auÂ
tomatically, press the
! AUTO ! button.
~ Adjusting the air distribution
You can manually se lect the vents where the
air will flow. To have the air distribution reguÂ
lated automa tically, press the
IAUTOI button .
~ I lil* Adjusting Seat heating/
ventilation*
Pressing the button switches the seat heatÂ
ing/ventilation on at the highest setting ( level
3). The L EDs indicate the temperature leve l.
To reduce the temperature, press the button
again. To switch the seat heating/ventilation
off, press the button repeatedly until the LED
turns off.
After 10 minutes, the seat heating/venti lation
automatically switches from level 3 to level 2.
I n vehicles without the four zone automatic
climate contro l*, buttons in the rear center
console control the seat heating for both outÂ
er rear seats*.
~ Switch the defroster on/off
The winds hield and s ide windows are defrost Â
ed or cleared o f condensation as quickly as
possible. The maximum amo unt of air flows
mainly from the vents below the windshield.
Recirculation mode switches off. The temperaÂ
ture should be set to 72
°F (22 °C) or higher.
The temperature is controlled automatically.
The
IAUTOI button switches the defroster off.
~ Switching rear window heater on/off
T he rear window heater only operates when
the engine is running. It switches off autoÂ
matically after 10 to 20 minutes, depending
on the outside temperature.
T o prevent the rear window heater from
switching off automatically , press and hold
the~ button for more than 2 seconds. This
r ema ins stored until the ignition is switched
off.
I SYNC I Synchronization*
When synchronization is switched on, the setÂ
tings for the driver's side are applied to the
front passenger's side (except for seat heat Â
ing/ventilation*). The rear seat is a lso
synchronized in vehicles with the 4-zone deÂ
luxe automatic cl imate control system*. SynÂ
chronization switches off if the sett ings are
adjusted on the front passenger's side or in
the rear*.
You can synchronize the settings in a row by
pressing and holding a knob. For example, to
apply the settings for the front passenger's s ide to the driver's side, press and hold the
knob on the front passenger's side.
Air vents
You can open or close the center and rear
vents in the cockpit and the vents in the rear
center console and door pillars using the
ridged thumbwheels. The levers adjust the diÂ
rection of the airflow from the vents.
,&. WARNING
- Do not use the recirc ulation mode for exÂ
tended periods of time . The windows
could fog up since no fresh air can enter
the vehicle. If the windows fog up, press
the air recircu lation button again immeÂ
diately to sw itch off the air recirculation
function or select defrost.
- Individuals w ith reduced sensitivity to
pain or temperature could deve lop burns
when using the seat heating function. To reduce the risk of injury, these indiv idu-
als shou ld not use seat heating . .,..
Page 89 of 312

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Starting off with a trailer
To prevent rolling back unintentionally on an
incline, do the following:
11-Keep the switch© pulled and depress the
accelerator. The parking brake stays applied
and prevents the vehicle from rolling backÂ
ward .
11-You can release the switch<®> once you are
su re that you a re develop ing enough forÂ
ward momentum at the wheels as you deÂ
press the accelerator.
D epending on the weight of the r ig (vehicle
and tra ile r) and the severi ty of the incl ine, you
may roll backwards as you start. Yo u can preÂ
vent rolling backwards by holding the parking brake switch<®) p ulled out and acce lerating -
just as you would when starting on a hill with
a conventional hand brake.
Emergency braking
In the event that the conventional brake sysÂ
tem fails or locks.
11-In an emergency, pull the switch(®) and
contin ue to p ull it to slow your vehicle down
with the parking brake.
11-As soon as you release the switch (®) or ac-
ce lerate, the braking process stops.
If you pull the switch<®> and hold it above a
speed of about 5 mph (8 km/h), the emergenÂ
cy braking function is initiated. The vehicle is
braked at all four wheels by activating the hyÂ
draulic brake system. Th e brake performance
i s similar to making an emergency stop
~ &..
In order not to activate the emergency brakÂ
ing by m istake, an audible warning tone (buzÂ
ze r) sou nds when the switch C®> is pulled. As
soon as the switch(®) is released, or the accelÂ
e rator pedal is dep ressed, emergency b ra ki ng
stops.
_& WARNING
Emergency braking should only be used i n
an emergency, when the normal foot brake
has failed or the brake pedal is obstructed .
On the ro ad 87
Using the parking b rake to pe rform emerÂ
gency brak ing will slow your vehicle down
as if you had made a full brake application.
The laws of physics cannot be suspended
even with ESC and i ts associated compoÂ
nents (ABS, ASR, EDL). In corners and
when road o r weathe r cond itions are bad,
a full brake appl ication can ca use the vehiÂ
cle to sk id or the re ar end to break away -
risking an acciden t.
Start-Stop-System
' Description
Applies to vehicles: wit h Start -Stop-System
The Start-Stop-System can help increase fuel
economy and reduce CO2 emissions .
In the Start-Stop-mode, the engine shuts off
automat ica lly w hen the vehicle is stopped,
such as at a traffic light. The ignition remains
switched on du ring this stop phase. The enÂ
gine wi ll be automat ica lly restarted when
needed.
The last Start-Stop-System sett ing (on/off usÂ
ing the button
I O\l ~I) will be restored when the
i gnition is turned on. The L ED in the
1(7() .. 1 butÂ
ton turns on when the Star t-Stop-System is
swi tched off man ually.
Basic requirements for the Start -Stop
mode
- The d rive r's doo r is closed.
- The d river ' seat belt is latched .
- The hood is closed .
- The vehicle must have been driven faster
than
2.5 mph (4 km/h) since the last stop.
- A trailer is not hitched to the vehicle.
_& WARNING
-Never let the vehicle roll with the eng ine
sw itched off. You cou ld lose control over
the vehicle. Th is can lead to a collision
and serio us in ju ries.
- The brake booster and the steering sup port do not work while the engine is
Page 92 of 312

90 On the road
facility for servicing as soon as possib le to
correct the malfunction.
Speed warning system
Introduction
The speed warning system helps you to stay
under a specified maximum speed.
The speed warning system warns you if you
are exceeding the maximum speed that you
have set . You will hear a warn ing tone when
your speed exceeds the stored value by ap proximately 3 mph (3 km/h). An indicator
light. (USA models) . (Canada models) in
the instrument cluster display also turns on at
the same time. The indicator light./.
turns off when the speed decreases below the
stored maximum speed.
Sett ing a threshold is recommended if you
wo uld like to be reminded when you reach a
certain maximum speed . Situations where you
may want to do so include driving in a country
with a general speed limit or if there is a
specif ied maximum speed for winter tires.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you should still
watch the speedometer to make sure you
are not driving faster than the speed lim it.
Setting the threshold
You can set, change and delete the threshold
in the MMI.
.. Se lect : ICAR lfunction button> Car systems
control button > Driver assist > Speed warnÂ
ing.
You can set any threshold between 20 mph
(30 km/h) and 150 mph (240 km/h). Settings
can each be adjusted in increments of S mph
(10 km/h).
Cruise control
Switching on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30kmlh) .
0
•
~
0
Fig. 94 Control leve r with set b utton
Fig. 95 Display: Se lected speed
.. Pull the lever to position (D c::> fig. 94 to
sw itch the system on.
.. Drive at the speed you wish to set.
.. Press button @ to set that speed.
T he stored speed and the indicator light
II (US models) ;El (Canadian mode ls) apÂ
pear in the instrument cluster display
c::> fig. 95 . The display may vary, depending on
the type of display in your veh icle .
T his information is also shown briefly in the
Head-up Display*.
Th e speed is kept constant via an engine outÂ
put adjustment or active brake intervent ion.
WARNING
-Always pay attention to traffic even when
the cruise control is switched on. You are
a.lways respons ible for your speed and
Ill-
Page 99 of 312

Audi adaptive cruise control and braking guard 97
When approaching a moving vehicl e up ahead,
the adaptive cruise contro l system automatiÂ
cally brakes to match that object's speed and
then maintains the stored distance.
If the veÂ
hicle ahead accelerates, adaptive cruise conÂ
trol will also accelerate up to the stored
speed .
The higher the speed, the greater the distance
in yards (meters) ¢.&. . The
Distance 3 setting
is recommended .
The distances prov ided are specified values .
Depending on the driving situation and the
how the vehicle ahead is driving, the actual
distance may be more or less than these tar Â
get distances.
The various symbols for the time increments appear briefly in the information line @
¢
page 94, fig . 101 when you change the set Â
tings .
,::::::,_,::::::, ___ Distance 1: This setting corre-
sponds to a distance of 92 feet/28 meters
when traveling at 62 mph (100 km/h), or a
time interval of 1 second.
,::::::, __ ,::::::, __ Distance 2: This setting correÂ
sponds to a distance of 118 feet/36 meters
when traveling at 62 mph (100 km/h), or a
time interval of 1.3 seconds .
,::::::, ___ ,::::::,_ Distance 3: This setting corre-
sponds to a distance of 164 feet/SO meters
when traveling at 62 mph (100 km/h), or a
time interval of 1.8 seconds .
,::::::, __ __ ,::::::, Distance 4: This setting corre-
sponds to a distance of 210 feet/64 meters
when traveling at 62 mph (100 km/h), or a
time interval of 2.3 seconds .
A WARNING
Following other vehicles too closely inÂ
creases the risk of collisions and serious
personal injur y.
- Setting short distances to the traffic
ahead reduces the time and distance
available to bring your vehicle to a safe
stop and makes it even more necessary
to pay close attention to traffic. -
Always obey applicable traffic laws, use
good judgment, and select a safe followÂ
ing d istance for the traff ic, road and
weather conditions .
(D Tips
-Distance 3 is set automatically each time
you switch the ignition on.
- Your standard settings are automatically
stored and assigned to the remote conÂ
trol key being used.
Selecting the driving mode
Applies to vehicles: with Audi adaptive cruise control
.. Select the desired driving mode in dr ive seÂ
lect <=;>
page 108.
(D Tips
Your settings are automat ically stored and
assigned to the remote control key being
used.
Prompt for dr iver intervention
Applies to vehicles: with Audi adaptive cruise contro l
Fig. 105 Instrument cluste r: request fo r dr ive r interÂ
vent ion
In certain situations, the system will prompt
you to take action . This could happen, for exÂ
amp le, if braking by the adaptive cruise conÂ
trol system is not enough to maintain enough
distance to the veh icle ahead .
The indicator light . and the symbol in the
display will warn you about the situation
<=;> fig. 105. You will also hear an acoustic sig-
nal. ..,.
Page 110 of 312

108 Audi drive select
Audi drive select
Driving settings
Introduction
Audi drive select makes it possible to experiÂ
ence different types of vehicle settings in one
vehicle. The driver can select three
Comfort,
Auto
and Dynamic modes in the MMI to
switch between a sporty and a comfortable
driving mode.
You can a lso adjust the setting according to
your preferences in the
individual mode. For
example, you can combine settings such as a
sporty engine tuning with comfortab le steerÂ
ing.
A WARNING
Improper use of the Audi drive select can
cause collisions, other accidents and seriÂ
ous personal injury.
Description
The vehicle setup in each mode depends on
the vehicle's features. The engine, transmisÂ
sion, steering, reversible safety belt tensionÂ
ers and adaptive air suspension are always inÂ
volved.
Engine and transmission
Depending on the mode, the engine and the
transmission respond quicker or in a more balÂ
anced manner to acce le rator pedal moveÂ
ments. In the sporty dynamic mode, the
transmission shifts at higher RPMs.
Air suspension
The adaptive air suspension/adaptive air susÂ
pension sport*
(Ai r suspension in the MMI) is
an electronically control led air suspension and
damping system. They are adjusted dependÂ
ing on the selected driving mode, the driver's
steering, braking and acceleration input and
the road surface, vehicle speed and load. A
sporty setting is generally used in vehicles
with adaptive air suspension sport*. The
vehicle clearance varies depending on the
selected mode and the speed .
The highway setting is activated automatically
when you drive above 75 mph (120 km/h) for
more than
30 seconds in the auto or dynamic
mode. The ground clearance is increased autoÂ
matically if the speed drops below
44 mph
(70 km/h) for more than 120 seconds.
Steering
The steering adapts in terms of steering effort
and steering ratios . Indirect steering that
moves easily, like the steering in comfort
mode, is best suited to long drives on a highÂ
way. In contrast, dynamic mode provides
sporty, direct steering .
The following applies to vehicles with dynamic
steering* : the steering ratio changes based on
vehicle speed in order to maintain optimum
steering effort for the driver at all times. This
sets the steering to be less sensitive at higher
speeds in order to provide improved vehicle
control. At reduced speeds, however, steer ing
is more direct in order to keep the steering efÂ
fort as minimal as poss ible when the driver is
maneuvering the vehicle. At low and average
speeds, dynamic steering additionally pro Â
vides more responsive steering performance.
Sport differential*
As a component of the all whee l dr ive system
(quattro)
r:!> page 202, the Sport differential*
distributes the driving power to the rear axle
depending on the situation . The distribution
of power varies depending on the selected
mode, from balanced (comfort) to agile (dyÂ
namic). The goal is a high level of agility and
ability to accelerate on curves . The vehicle is
very respons ive to steering .
Curve light*
The curve light adapts to driving on curves.
The pivoting action and the lighting are also adapted to the mode.
Adaptive cruise control*
The behavior when accelerating can be adjustÂ
ed from comfortab le to sporty, depending on ..,.