reset AUDI TT 2013 Owner´s Manual

36 Opening and closing
-The operation of the remote control key
can be temporarily disrupted by interfer­
ence from transmitters in the vicinity of
the vehicle working in the same frequen­
cy range (e.g. a cell phone, radio equip­
ment) .
- In order to make sure the locking func­
tion is working, you should always keep
your eye on the vehicle to make sure it is
properly locked .
- Do not use the remote control if you are
inside the car, otherwise you may unin­
tentionally lock the vehicle, and then you
would set off the anti-theft alarm when
you try to start the engine or open a
door. In case this happens anyhow, push
the unlock button
CD .
- Use the panic function only if you are in
an emergency situation.
Resetting the remote control
The remote control must be reset if the vehi­
cle does not unlock .
.,,. Press the unlock button CD on the remote
control.
.,,. Manually unlock the driver's door lock with
the mechanical key within 30 seconds.
.,,. Press either the lock-
lD or the unlock CD but­
ton to complete th e reset sequence.
Operating locks with the key
To lock and unlock the vehicle from the out­
side , turn the key in the lock of the driver's
door .
Fig. 29 Key turns for ope ning and clo sing.
.,,. To unlock the vehicle, turn the key to the
opening position@¢
fig. 29.
.,,. To lock the vehicle, turn the key in the lock
of the driver's door to the lock position
@
¢ &_ .
A WARNING
Always read and heed WARNING¢.&. in
General description on page 34.
Locking and unlocking the vehicle from
inside
The vehicle can be locked or unlocked from
the inside using the power locking switch .
Fig. 30 Sec tion from center conso le: Ce ntra l locking
switch
.,,. Press the upper part of the power locking
switch
@ to lock the vehicle ¢&_ .
.,,. Press lower part of the switch
en to unlock
the vehicle .
If you lock the vehicle using the power locking
switch , please note the following:
- You cannot open the doors or the rear lid
from the
outside (increased security, for ex ­
ample when you are stopped at a red light).
- You can unlock and open the doors from the
inside by pulling on the door handle .
-If the driver's door is opened (after you have
locked the vehicle from the inside using the
power locking switch), the door will remain
unlocked to prevent you from locking your­
self out of your vehicle. After you close the
door, you have to lock the driver 's door
again.
- If you have a crash and the airbag is activat-
ed, the doors automatically unlock. ..,.

42 Clear vision
Clear vision Lights
Switching the headlights on and off
Fig . 39 Instr ument panel: l ight sw itch
Fig. 40 Instr ument pane l: ligh t switch w ith dayti me
running lights (DR L)
The light switch must not be overturned past
the stops in
either direct ion.
Switching on automatic headlight
control*
• Turn the light switch to AUTO* ¢ fig. 39.
Switching on the side marker lights
• Turn the light switch to :;oo:.
Switching on the headlights and high
beam
• Turn the light switch to tD .
• Push the high beam lever forward towards
the instrument panel¢
page 44.
Switching off the lights
• Turn the light switch to 0.
The head lights only work when the ignition is
switched on. While start ing the engine or
when switching off the ignition, the head- lights
will go off and only the side ma rker
lights will be on.
Daytime running lights (DRL) (USA
models)
T he daytime running lights can be turned on
or off using this function. If the function is ac­
tive, the daytime ru nning lights are turned on
automatica lly when the ign it ion is switched
on.
T he daytime running lights are activated
only
when the light switch is at the AUTO* or DRL *
position.
Daytime running lights (Canada models
only)
The daytime running lights are activated only
when the light switch ¢ fig. 39 is either at the
0 or the :;oo: pos ition.
T he daytime r unning lights funct ion cannot be
turned off.
Automatic headlight control*
In the switch position AUTO the automatic
headlight control
is turned on. The low
beams are turned on automatically through a
light sensor as soon as amb ient b rightness
(e .g. when driving into a tunnel) falls below a
value preset at the factory. When ambient
brightness increases aga in, the low beams are
turned off again automatically ¢.&..
In the
AUTO position the low beams are
switched off automatically when the ignition
is turned off .
Light Sensor Malfunction*
In the event of a light sensor malfunction, the
driver is notified in the instrument cluster dis­
play:
El Automatic headlights/automatic wipers
defective
For safe ty reasons the low beams are turned
on permanently with the switch in
AUTO* .
However , you can conti nue to turn the lights
on and off using the light switch. Have the
Ill>-

The speed warning system has two warning
thresholds
that function independently of
each other and that have somewhat different
purposes:
Speed warning 1
You can use speed warn ing 1 to set the maxi­
mum speed while you are driving. This setting
will remain in effect until you turn
off the igni ­
tion, assuming that you have not changed or
reset the setting.
The speed warning symbo l
(mj (USA models)/
(SJ (Canada models) in the warning 1 display
appears when you exceed the maximum
speed.
It goes out when the speed falls below
the stored max imum speed.
The speed warning symbo l wi ll also go out if
the speed exceeds the stored maximum speed
by more than about 2S mph (40 km/h) for at
least 10 seconds. The stored maximum speed
is deleted.
Setting speed warning l <=:> page
75.
Speed warning 2
Stor ing warn ing 2 is recommended if you al­
ways want to be reminded of a certa in speed,
for example when you are traveling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a spec ified
speed for winter tires.
The speed warning 2 symbol,
(zj els)/
(•j (Canada models) appears in the dis­
p lay when you exceed the stored speed lim it.
Unlike warning 1, it will not go out until the
vehicle speed drops below the stored speed limit .
Sett ing speed warning 2 <=:>page 76.
@ Tips
Even though your vehicle is equipped with
a speed wa rning system, you should sti ll
watch the speedometer to make sure you
are not driving faster than the speed lim it.
On the road 75
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the button.
Fig. 73 Sect ion of instrument clus ter: Set/C heck but ·
ton
Storing the maximum speed
.,. Drive at the des ired maximum speed .
.,. Press the knob buttonr=:>fig .
73 unti l the
speed warning symbol
[iJ (USA models)/ ~
(Canada models) appears.
Resetting the maximum speed
.,. Drive the vehicle at a speed of at least
3 mph (5 km/h)
.,. Press the knob for more than 2 seconds.
The speed warning symbol
(G:l (USA models)/
i•j rcanada models) will appear briefly in the
display when you release the button to indi­
cate that the maximum speed has been stored
successfully .
The maximum speed remains stored until it is
changed by pressing the button aga in brief ly
or until it is deleted by a lengthy push on the
button.

76 On the road
Speed warning 2: setting a speed limit
Switches in the wiper arm are used to operate
warning threshold
2 .
'----I ®
Fig. 74 Wiper lever: Tr ip computer con trols
To store maximum speed
> Turn off the ignit ion.
> Briefly press the button in the instrument
cl uster ¢
page 75, fig. 73. The odometer
and the digital clock are now illuminated .
> Press the button for at least 2 seconds. The
currently stored maximum speed appears in
the display
or the crossed out symbol for
warning threshold 2, if no max imum speed
was set previously.
> Press the function selector sw itch in the
wipe r lever @¢
fig. 74 up or down to
change the set value. Values run up or dow n
i n steps of 6.2 mph (10 km/h).
To delete maximum speed
> Turn off the ignit ion .
> Briefly press the button in the instrument
cluster ¢
page 75, fig . 73. T he odometer
and the digital clock are now illumi nated.
> Press the button for at least 2 seconds . Th e
cu rrently stored maxim um speed appears in
the display.
> Press the reset button in the wiper lever ®
¢fig . 74 until the crossed out speed warn­
ing symbol for warning threshold 2 appears
i n the display.
A few seconds after the adjustment is com­
pleted, the illumination for the odometer and
the dig ital clock will go out.
(D Tips
This warning threshold can a lso be con­
trolled thro ugh the tr ip computer
¢ page 25, Navigating the menu.
Cruise control
Switching the system on
The cruise control system makes it possible to
drive at a constant speed starting at 20 mph (30 km/h) .
®-
Fig. 75 Contro l leve r with set b utton
Fig. 76 D isplay : Se lecte d speed
> Pull the lever to position (D ¢ fig. 75 to
switch the system on.
> Dr ive at the speed you w is h to set.
> Press button @ to set that speed.
.., ....
i
The display ¢ fig. 76 will show the set speed .
The display may vary depending on the type of
display in your vehicle. The indicator light
M;ll)~14 (US model)/ . (Canadian model) will
also light up in the instrument cluster .
A WARNING
- Always pay attention to traffic even when
the cruise control is switched on. You are
always responsib le for your speed and

the distance between your vehicle and
other vehicles.
- For safety reasons, the cruise control
should not be used in the city, in stop­
and-go traff ic, on twisting roads and
when road conditions are poor (such as
ice, fog, grave l, heavy rain and hydro­
planing) -risk of acc ident .
- Turn off the cruise control temporari ly
when entering turn lanes, highway exit
lanes or in construction zones .
- Please note that inadvertent ly "rest ing"
yo ur foot on the accelerator peda l causes
the cruise control not to brake. This is
because t he cr uise con trol is overridden
by the driver's acce lerat ion.
(D Tips
- Vehicles with manual t ransmission: You
can attain the set speed only if the cur­
r ently e ngaged gear a llows i t and the en­
gine i s not stressed. Shift ing to a h igher
or lower gear p romp tly will allow t he en­
gine to run smoothly.
- The cruise cont ro l cannot main tain a
constant speed when driving downhill.
The vehicle will accelerate unde r its own
weig ht. Downsh ift to a lower gear or use
the brakes to slow down.
Changing speed
"' Press lever in the 0 or 0 direction
i=> page 76, fig . 75 to increase or decrease
you r speed .
"' Re lease the lever to save that speed.
You can a lso press the accelerator pedal down
to inc rease your speed, e.g . if yo u want to
pass someone . The speed you saved ea rlier
will resume as soon as you release the acceler­
ator peda l.
If , however, you exceed your saved speed by
5 mph ( 10 km/h) for longe r than 5 minutes,
the cruise cont ro l w ill tu rn off tempora rily .
The symbol will go o ut but the saved speed
will be retained .
On the ro ad 77
Presetting your speed
You can preset your desired speed while the
vehicle is not moving.
"' Turn on the ignition.
"' Pull lever into position
(D c:> page 76,
fig . 75.
"' Press the leve r in the 0 or 0 direction to
increase or decrease your speed.
"' Re~asethelevertosave thatspeed.
This function makes it possible, for example,
to save the speed you want before dr iving on
the highway. Once on the h ighway, act ivate
t h e cr uise con trol by pulling the lever toward
(D .
Switching the system off
Temporary deactivat ion
"' Press the brake pedal, or
"' Keep the cl utch pedal pressed down longer ,
or
"' Press the lever into position @(not clicked
into place)
¢page 76, fig . 75, or
"' Drive for longer than 5 minutes at more
than 5 mph (10 km/h) above the stored
speed.
Switching off completely
"' Press lever into position @(clicked into
place), or
"' Switch the ignit io n off.
The system retains the saved speed if you de­
activate the cruise control temporar ily. To re­
sume the saved speed, re lease the brake or
clutch pedal and pull the lever to position
(D.
Switching the ignit ion off erases the saved
speed.
A WARNING
You shou ld only return to the saved speed
if it is not too fast for the current traffic
conditions -ris k of an accident!

remain continuous ly illuminated . This se ­
quence will continue upon subsequent vehicle
start-ups as long as the ma lfunction ex ists.
When the malfunct ion indicator is ill uminat­
ed, the system may not be able to detect or
signa l low tire pressure as intended. TPMS
malfunct ions may occur for a variety of rea­
sons, including the installat ion of replace­
ment or alternate tires or wheels on the veh i­
cle that prevent the TPMS from funct io ni ng
properly. Always check the TPMS malfunct ion
tellta le afte r replacing one or more t ires or
wheels on your veh icle to ensure that the re­
p lacement or a lternate tires and wheels allow
the TPMS to continue to function properly.
Tire pressure indicator appears
Applies to vehicles: with tire pressure monitoring system
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig. 1 47 Disp lay : under infla tion warn ing
Using the ABS sensors, the tire pressure moni ­
toring system compares the t ire tread circum­
fe rence and vibration characteristics of the in­
d iv idual tires . If the pressure decreases in one
or mo re tires, th is is indicated in the instru­
ment clus ter with a warning symbol
RE and a
message
'* fig. 147. The dr iver message in the
d isp lay goes out after 5 seconds. The driver
message can be d isplayed again by pressing
the
! CHECK I button @¢ page 10, fig . 3 . If on ­
ly one tire is affected, the display will indicate
its pos ition.
The ti re pressure monito ring m ust be reset in
the menu display each time the pressures are
ad justed (e.g. when switching between parti-
Tire s an d wheel s 215
al and fu ll load pressure) or after changing o r
replacing a tire on your vehicle '*
page 216.
The TPMS indicator on ly mon itors the t ire
pressure that you have previously stored . You
can f ind the recommended tire pressures for
your vehicle on the label on the driver's door
pillar ¢
page 200.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the t ire press ure in one or more tires is too
low,
- the tire has structural damage,
- the t ire press ure was changed, wheels rotat -
ed or rep laced but the TPMS was not reset
¢ page 216.
Warning symbo ls
RE L oss of pressure in a t least one tire ¢ ,&..
Check the tire or tires and rep lace or repa ir if
necessary . The indicator light
RE in the inst ru­
ment cluster a lso i lluminates
¢ page 13 .
Check/correct the press ures of all four tires
and reset TPMS in the menu display .
Iii;~, (T ire Pressure Monitoring System) Ti re
pre ssure! System malfun ction .
Ifllilff' ap­
pears after switching the ignition on or whi le
driv ing and the indicator light
RE in the in­
strument cluster blinks for approx imately one
minute and then stays on, there is a system
malfunction .
Attempt to store the correct tire pressure '*
page 216. If the indicator light does not
turn off or if it turns on shortly thereafter, im ­
med iate ly dr ive your vehicle to a n author ized
Audi dealer or author ized repair fac ility to
have the malfunct io n cor rected.
.8, WARNING
-
- If the tire pressure ind ic a tor ap pears in
the ins trumen t cluster display, one or
more of your tires is significant ly under­
inflated . Reduce yo ur speed immediately
and avoid any hard steer ing or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures.
~
•
•

216 Tires and wheels
Inflate the tire pressure to the proper
pressure as indicated on the vehicle's tire
pressure label¢
page 200. Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability .
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regularly.
- Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor ind i­
cator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle .
Your vehicle registration becomes invalid
if you use these tires when not permit­
ted. Damage to your veh icle or accidents
could also result.
- If you switch between standard and run­
flat tires, an authorized Audi dealer or
qualified workshop must reprogram the
control module .
@ Tips
-The tire pressure monitoring system
stops working when there is an ESC/ABS
malfunction.
- Using snow chains may result in a system
malfunction .
- The tire pressure monitoring system on
your Audi was developed using t ires with
the "AO" or "RO" identification on the
tire sidewall ¢
page 207. We recom­
mend using these tir es.
Reset tire pressure monitoring system
(Stepl)
Applies to veh icles: w ith tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset in
the menu display.
----- ®
Fig. 148 Wipe r lever: Contro ls fo r the menu d isplay
Fig. 149 Disp lay: S ta rt m enu
I Rese t I button @ and rocker switch @
¢
fig. 148 functions:
To open the menu
" Press the I Reset ! button @ unt il the menu
disp lay
~fig. 149 appears
Selections and settings
" Press the rocker switch @ to reach a menu
disp lay. The switch is operated the same as
the display (up/down) .
Entering and confirming
" Press the I Reset I button @.
Returning to the Start menu
" Press the I Rese t I button longer than 2 sec­
onds to return from any menu level to the
Start menu.

@ Tips
-Before resetting the TPMS, the current
pressures of
all four tires must corre­
spond t o the specified va lues. Adjust the
tire pressu re and reset the pressure in
the tire pressure mon itor ing system ac­
cord ing to the load yo u are carry ing
c::> page200.
- Do not store the tire pressure if there are
snow cha ins on the tire .
Reset tire pressure monitoring system
(Step2)
A pplies to vehicles: with t ire pressure monitoring syste m
Fig. 150 D isplay: Tire pressure
Fig. 151 D isp lay: Tir e pressure
I Reset ! button @ and rocker sw itch @
c::> page 216, fig. 148 functions:
Storing tire pressure s
.,. Turn on the ignition.
.,. Se lect the menu :
> Adjusting* > Tire pres-
sure
> Store .
Entering and confirming
.,. Se lect the menu: Store now
.,. Press the
!Reset I button @.
.,. Se lect the menu: Confim
.,. Press the
!Reset I button @. Tires and wheels 21
7
Returning to the Start menu
.,. Press t he I Reset l butto n longer tha n 2 sec­
onds to re turn from any menu level to the
Start men u.
(D Tips
-Before rese tt ing the TPMS, the c urrent
pressures o f
all four tires must corre­
spond to t he spec ified values . Adj ust t he
t ir e pr essure and reset the pressure in
the tire pressu re monitoring system ac­
co rding to the load you are ca rrying
c::> page 200.
- Do not store the tire pressure if there are
snow chains on the tire.
Run-flat tires
Introduction
Applies to vehicles: wit h Run-fla t tires
Run-flat tires help keep you moving if a tire
goes flat.
Re inforced sidewalls give the t ires r un-flat ca­
pabili ty if tire pressure is lost .
We recommend that run-flat tires o nly be
mounted on vehicles that were orig inally
equipped with these special t ires at the facto­
ry an d have a Tire Pressu re Monitoring Sys­
tem .
Run-flat tir es can be identifi ed by th e letters
"RSC" on the tire sidewall.
If you do change the tires on your veh icle from
no rma l to run-flat tires, you must buy the
special rims required fo r run-flat tires, and the
T ire Pressu re M on itor ing System must be re­
programmed by an authorized Aud i d ealer o r
othe r qualified wo rkshop .
What do run -flat tires do?
These special tir es have run-flat capab ilities
that help keep you moving if a tire loses pres­
s ur e and goes flat. Under favorab le condi tions
t ir es can be dr iven
at least 30 miles (SO km) ,
but you mus t not drive fa ster than SO mph
( 80 km/h)
c::> page 218, Driving with run-fla t
tires .
Ill-

Fuse Location, Instrument Panel left
0
Fig. 166 Fu se ca rrier behin d th e in strum en t pane l end
fa ce, cover re move d
Some of the equipmen t items lis ted a re op­
tional or only available on certain model con ­
f igurations.
N ote th at the foll ow ing table is ac curate at
the t ime of go in g to press and is subje ct to
c hang e. In t he event of d iscr epan cies, the la­
b el on the in side of th e cove r alw ay s take s
precedence .
The power sea ts are pro te ct ed by circu it
break ers,
which automatically reset after a
few seconds after the overload has been rem­
ed ied .
No. Equipment
1
2
3
Engine relay, fuel tank contro l
unit, A irbag Off light , light
switch (sw itch illumi nation), di -
agnosti c connector
ABS, ASR, ESC, brake light switch
AFS headlight (le ft)
Amps
10
5
5
Fu se s and bulb s 229
No.
4
5
Equipment
Oil level sensor (extended main-
tenance interval) (WIV), tire
pressure monitoring system,
switch for Electronic Stabiliza-
tion Control (ESC), AFS head-lights (control unit), A/C system
(pressure sensor), backup light
switch
Automatic headlight range con­ trol, AFS headlight (right) /
manual headlight range con­
trol, halogen headlights
Control unit for CAN data trans-
6 fer (gateway), electromechani­ cal steering, automatic trans­
mission shift gate
7 Acoust
ic Park Assist, automatic
dipping interior rear view mir-
ror, garage door opener, heata­
ble windshield washer nozzles,
washer pump, w ind deflector
re lay (Roadster)
--r-HaldeX clutch/Haldex clutch
(TTS)
8
Amps
5
5/10
5
5
5/10
9 Control un it Audi magnetic ride 5
----10 Airbag control unit 5
Mass airflow sensor, crankcase
11 heat ing
Door control unit (central lock-
12 ing driver/passenger)
13 Diagnostic conne ctor
Rain sensor, automatic trans-
14 mission shift gate
15 Roof light (inter ior lighting)
16 A/C system (control unit)
17 Tire pressure monitoring sys­
tem (control un it)
--~-18 Not used
19 Not used 5/10
10
10
5
5
10
5
I
I
I
20 -------21 Fuel injectors (gasoline engine) 10
22 Wind deflecto r (Roadster) 30
23 Horn 20
IIJ>,

254 Index
Park assist . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Park ing ... .. ................ ... 74,82
Parking brake ....................... 73
Park ing brake warn ing ................ 15
Park ing on a decline (downhill) ... .. .... 74
Parking on an incline (uphill) ... ... ... .. 74
Parts rep lacement .................. 245
PASSENGER AIR BAG OFF light . .. ..... 119
Passive safety system . . . . . . . . . . . . . . . . . 90
Pedals .. .... .................. ... .. 95
Phys ica l pr inciples of a frontal coll is ion . 101
Polishing .. .. ............. .. .. .. .. . 167
Pollen filter . . . . . . . . . . . . . . . . . . . . . . . . . 67
Poll utant fi lter .. .. ..... ... .. .. .... .. 67
Powe r locking switch ............ ..... 36
Power locking system . . . . . . . . . . . . . . . . . 34
Conven ience close/open feature ..... .. 40
Lock ing and unlocking the vehicle from
in side ... .. ... .... ...... ... ... .. .. 36
Opening and clos ing the w indows ...... 40
Rear lid/t runk l id ................... 37
Remote cont rol .......... .. .. .... . . 33
Un lock ing and locking veh icle ... .. .. . . 35
Powe r outlets
63
Powe r seats
Ad justment ............. .. .. .. .. .. 56
P ower steering
refer to Electro -mechanica l power as -
sist . . . . . . . . . . . . . . . . . . . . . . . . . 17, 155
Powe r window switches . . . . . . . . . . . . . . . 39
Reactiva ting t he system . .. .. .. .... .. 4 1
Pregnant women Specia l cons iderations when wearing a
safety belt .... .... ...... .. .. .. .. . 105
Programming the Homelink ® universal re­
mote contro l . . . . . . . . . . . . . . . . . . . . . . . . 87
Pr ope r occupant sea ting pos it ions .. .... 9 1
Proper safety belt pos it ion ........ .... 105
Prope r seat ing posit ion
Front passenger . . . . . . . . . . . . . . . . . . . . 92
Occupants ......................... 91
Rear passengers . . . . . . . . . . . . . . . . . . . . 93
Q
Qua rtz clock . . . . . . . . . . . . . . . . . . . . . . . . 11 quatt
ro ®
refer to All-whee l drive
Question What happens to unbelted o ccupants?
Why sa fe ty belts? ............. ... .
R
15S
102
100
Radiator fan ...... ............. .... 189
Rain sensor defective . . . . . . . . . . . . . . . . . 21
Reading ligh ts ... .. .. ... ..... ... .. .. . 45
Rea r lid ....... .... .... ........... .. 37
Emergency re lease . . . . . . . . . . . . . . . . . . 38
Rear light defect ive . . . . . . . . . . . . . . . . . . 20
Rea r spo ile r . .. .. .. ... .. ..... ... .. .. 153
Rear v iew m irror ........ ........... .. 47
Rear window defogger . . . . . . . . . . . . . . . . 70
Rea r window s helf . . . . . . . . . . . . . . . . . . . 58
Refuell ing .. .... .. ............. .... 178
Re lease lever for hood . .. ..... ... .. .. 180
Remote contro l . . . . . . . . . . . . . . . . . . 33, 36
Remote contro l garage door opener
(Homelink ®) .. .. .. ............. .. .. . 87
Remote maste r key
U nlocking and locking ... .... ... .. .. . 35
Remote rea r lid re lease . ...... ...... .. 37
Repair ma nuals ..................... 243
Repa irs
Airbag system ... .. ... ..... ... .. .. 122
Rep lacement parts ........... ....... 245
Rep lacing
Wheel rims .... .. ............. .... 207
Rep lacing a fuse ... .. .... .... ... .. .. 228
Replacing light bulbs ........... ... .. 231
Rep lacing tires and wheels ........ .... 208
Rep lac ing windsh ield w iper b la d es . .. .. . 51
Repo rting Sa fety Defects .............. 98
Reset button . . . . . . . . . . . . . . . . . . . . . . . . 12
Resetting remote contro l . . . . . . . . . . . . . . 36
Retractor . . . . . . . . . . . . . . . . . . . . . . . . . . 104
Reverse (Automat ic transm iss ion) .. .... . 81
Rims Cast alloy ..... ....... ........... . 169
Replac ing . .... .. ............. .... 20 7
Stee l rim s ... .. .. ............. .... 169