engine oil AUDI TT COUPE 2009 Owner's Manual

___________________________________________ C_ h_e _c_ k_ i_n ...::g a....- a_n _d_ f_il _li _n --=g ------
•
Engine oil consumption
The engine in your vehicle depends on an adequate
am ount of oil to lubricate and c ool all of its moving parts.
In order to provide effective lubrication and cooling of internal
engine components, all internal combustion engines consume a
certain amount of oil. Oil consumption varies from engine to engine
and may change sign ificantly over the life of the engine . Typically,
engines with a specified break-in period (see~
page 190) consume
more oil during the break-in period than they co nsume after o il
consumption has stabilized .
Under normal conditions, the rate of oil consumption depends on
the quality and viscosity of the oil, the RPM (revo lutions per minute)
at which the engine is operated, the ambient temperature and road
conditions. Further factors are the amount of oil dilution from water
condensation or fue l residue and the oxidation level of the oil. As
any engine is subject to wear as mileage bu ilds up, the oil consump ­
tion may increase over time until rep lacement of worn components
may become necessary .
With all these variables coming into play, no standa rd rate of oil
consumption can be estab lished or specified. There is no a lternative
t o regula r and frequent checking of the oil level, see Note.
I f the yellow engine oil level warning symbol in the instrument
cluster _ lights up, y ou should check t he oi l level as soon as
possible
with the oil dipstick~ page 221. Top off the oil at your
earl iest co nvenience ~
page 222.
& WARNING
Before you check anything in the engine compartment , always
read and heed all WARNING S
~ & in "Working in the engine
c ompartment " on
page 217 .
0 Note
Driving with an insuff ic ie n t o il level is l ikely to cause severe damage
to the engine.
[ i ] Tip s
• The oil pressure w arning display ce,. is not an indi cator of the oil
level . Do not rely on it. Instead, check the oil level in your engine at
regular interv als , prefe rably ea ch time you refuel , and always before
going on a long trip.
• I f you have the impression your engine consumes excessive
amoun ts of oi l, we recommend tha t you consult your Audi dealer to
have the cause of your concern properly diagnosed . Keep in mind
that the accurate measureme nt of oil consumption requires great
care and may take some time. Your Audi dealer has instructions
about how t o measure oil consumption accurately. •
Checking the engine oil level
Vehicle care I t •
Fig. 13 9 Illu stra tion of
pri nciple 1 : Mar ker s on
oi l dip sti ck ...

-Checking and filling P'll:I ---=---------------
M ,...
9
i
Fig . 140 Illustr atio n of
p rin ci pl e 2: Marke rs o n
oi l d ips tick
Before you check anything in the e ngine compartment,
always read and h eed all WARNINGS => & in "Working in
the engine compartment" on
page 217.
D ete rmining oil l ev el
- Park your vehicle so that it is horizontally level.
- While at operat ing state temperature, briefly let the
engine run at id le and then shut it off .
- Wait approx. two minutes.
- Pull ou t the oil dipst ick. Wipe off the oil dipstick with a
clean cloth, and s lide it back in as far as it will go .
- Pull it back out and read off the oil level =>
page 221,
fig. 139 or ::::> fig. 140 . Top off the engine oil, if applicable
=>
page 222 .
Oil level with in range @
- Do not add oil.
Oil l evel within rang e
@
-You can add oil. Aft erwards, the oil level sho uld be wit hin
range @. Oil l
evel within rang e
©
You must add oil. Afterwards, the oil level should be
within range @.
The oil level needs to be checked at regular intervals . The best times
to do this are whenever you refue l and prior to long trips .
Depending on the way the vehicle is driven and the operating condi­
tions, oil consumption can be up to 1 quart per 1.200 mi les (1 liter
per 2.000 km). Consumption may be higher within the first 3 .000
miles (5.000 km) .•
Adding engin e oil "l=:7:
Fig. 14 1 E ngin e
co mpartme nt: O il fille r
ca p lo cation
Before you check anything in the engine compartment,
always read and heed all WARNINGS ::::> & in "Working in
the eng ine compartment" on
page 217.
- Unscrew the cap~ to the engine oil filling hole
::::> fig .141.
- Carefully top off with the appropriate oil in 0.5 liter doses .
- Check the oil leve l again after two minutes ::::>
page 221.
-Top off t he oil ag ain , i f n ecessary . ._

Checking and filling -
--------------~-
•
-Screw the ca p back o n the filling h ole and sli de th e oil
dips tick in as far as it wil l g o .
& WARNING
• While topping off , the oil must not come in contact with hot
engine parts -fire haz ard!
• The oil filler cap must be properly secured to prevent oil from
being sprayed on the hot engine and exhaust system when the
engine is running -fire hazard!
• If your skin has come in contact with the engine oil , you must
subsequently cleanse it thoroughly.
0 Note
• T he oil level must not be above ran ge @ -da nge r of co nverter or
engine damage! Contact an authorized dealership to draw off oi l, if
n ec essary.
• Audi does not recommend the use of oil additives . They may
damage the engine and adversely affect your New Vehicle Warranty.
W For the sake of the environment
• Unde r no circumstances can the o il come in co ntact w ith the
sewage network or the soil.
• Observe an d follow le gal regulat io n s when d ispos ing o f empty
oi l containers. •
Changing the engine oil
We recom men d th at ha ve yo ur oil c hang ed by an a utho­
r iz ed A ud i dealer o r a qualified servi ce s tatio n.
Befo re yo u ch ec k anything in the e ngine compa rtment, always read
and heed all WARNINGS=>
& in "Work ing in the en gine compart ­
ment" on
page 217 .
The engine oi l must be changed according to the interva ls specified
i n yo ur War ra n ty
& M ain te na n ce booklet . This is very i mportant
because the lubricating properties of oi l d iminish g radua lly during
no rma l vehicle use .
U nde r some circu msta nces the e ng in e o il s hou ld be cha nged mo re
frequently. Change oil more often if yo u drive most ly short
dista nces, opera te th e ve hicle i n dusty areas or under predo mi­
nantly stop -and-go traffic conditions, or have your vehicle where
t empe ra tu re s rema in bel ow free zin g for e xtended per iods .
De tergent additives in th e oil will make fr esh oi l loo k dar k aft er the
eng ine ha s been ru nning f or a sho rt ti me. T his i s no rm al and is not
a reason to c hange th e o il more ofte n than reco mme nde d.
Because of the problem of proper disposal, along with the spec ial
to ols an d necessa ry ex pertise requ ired, we stro ngly reco mmend
that you have your oi l cha nged by an authorized
Audi dealer or a
q ua lif ied serv ice s ta tio n.
If you choose to change your oil yourself , please note the following
impo rtant infor mati on:
& WARNING
To reduce the risk of personal injury if you must change the engine
oil in your vehicle yourself :
• Wear eye protection .
• To reduce the risk of burns from hot engine oil , let the engine
cool down to the touch.
• When removing the oil drain plug with your fingers , stay as far
away as possible . Always keep your forearm parallel to the ground
to help prevent hot oil from running down your arm .
• Drain the oil into a container designed for this purpose, one
large enough to hold at least the total amount of oil in your engine .
• Engine oil is poisonous . Keep it well out of the reach of children . _,,,
Vehicle care
I t •

-~_C_ h_e _c _ k_ i_n ...:::g::;...._ a_n_ d_ f_ i_ll _in -'g:::;.._ ___________________________________________ _
& WARN ING (c o ntinued )
• Continuou s contact with used en gine oil i s harmful to your
sk in. Alway s prote ct your skin b y wa shi ng oil off thoroughly with
soap and water .
0 Note
Never mix oil additives with your engine oil. These additives can
damage your engine and adversely affect you r Audi Limited New
Vehicle Warranty.
<£> For the sake of the environment
• Before changing your oil, first make sure you know where you
can proper ly dispose of t he used oil.
• Always dispose of used engine oil properly . Do not dump it on
garden soil, wooded areas, into open strea ms or down sewage
drains .
• Recycle used eng ine oi l by taking it to a used eng ine oi l collec ­
tion facility in your area, or contact a service station. •
Engine cooling system
Coolant
The e ngine coolant perfor ms tw o functions: i t kee ps the
en gine from overheatin g and i t pro tects the engi ne from
freezing in the winter.
The cooling system is sea led and general ly requires litt le attention.
The coo ling sys tem has been f illed at the factory with a permanen t
coo lant which does not need to be changed. The coolant consists of
a mixture of water and the ma nufacturer 's glyc ol- basedco olan t
additive
G12++ antifreeze w ith anti corrosion additives (50% for USA models; 60% for Canadian mode
ls) . T his mixture both assures the
n ecessary fros t pr otection a nd protects metal co mpo nents in the
engine's cooling system from corrosion and scaling. It also raises
t he boil ing point of the coolant .
Do not reduce the concentration of the coo lant in the su mmer by
adding plain water.
The proportion of coolant additive mu st be at
lea st 50 % but not more than 60 %
to maintai n antifreeze pro tection
and cooling efficiency. If the coolant frost protection is too low, the
coo la nt co uld free ze and damage the vehic le heating and engine
coo ling system .
For year-round driving, antifree ze is added at the factory for temper­
atures down to:
• - 31 °F ( -35 °C) USA
• -40 °F ( -40 °C) Canada.
You can mix the
G 12+ + coolant additive with other additives (G12+
or G12). Always check w ith your authorized Audi dealer.
& WARNING
Before you check anything in the engine compartment, alway s
read and heed all WARNINGS
~ & in "Working in the engine
compartment " on
page 217.
0 Note
• Before winter sets in, have the coolant checked to see if the
coo lant additive in your vehicle is suff icient to meet the c limate
co nd itions . This is e special ly impor tant i f you live in a region where
the winter is extremely cold. If necessary, increase the proportion of coo lant additive t o 60%.
• When adding coolant additive to your cooling system,
r emem ber:
- We recommend using on ly coolant additive
G 12+ + (check the
l abel) for your veh ic le . Th is coolant additive is available at autho -
rized Audi dealers. Other types of antifreeze can significantly ._

Checking and filling -
---------------------=----"=---------
reduce corrosion protection. The resu lting corrosion can cause a
loss of coolant and serious engine damage.
• Do not add any type of radiator leak sealant to your vehicle's
engine coolant. Adding radiator repair fluid may adverse ly affect the
function and performance of your cooling system and cou ld result
in damage not covered by your New Vehicle Limited Warranty. •
Checking the engine coolant level
The engine coolant level can be checked with a quick
gla nce .
Fig . 142 Engine
co mp artm ent : coo lan t
e xpa nsion t ank
Before you check anything in the engine compartment,
always read and heed all WARNINGS=> & in "Working in
the engine compa rtment" on
page 217.
- Switch the ignition of f.
- Read the coo lant l eve l at the coo lant exp ansio n tank
==> fig. 142. With a col d e ngine, it must b e above the
"min" mar k. Wit h a hot engine, it can be a little above t he
indicated range.
The location of the coolant expansion tank can be seen in the
engine compartment i llustration. To obtain an accurate reading, the engine must be switched off.
The expansion tank in your vehic
le is equipped with an e lectric
coolant level sensor.
When the coolant leve l is too low, the warning light in the Auto ­
Check System =>
page 34 will blink un til you add coolant and the
level has been restored to normal. Even though there is an e lectric
coo la n t level sensor, we still recommend you check the coolant level
from time to time .
Coolant loss
Coolant loss may indicate a leak in the cooling system . In the event
of coo lant loss, the co oling sys tem shou ld be i nspected immedi­
ate ly by your authorized Audi dealer . It is not enough merely to add
coo lant .
In a
sealed system , losses can occur only if the boiling point of the
coolant is exceeded as a result of overheating .
0 Note
Do not add any type of radiator leak sea lant to your vehicle's engine
coolant. Adding rad iator repair fluid may adversely affect the func ­
tion and performance of your coo ling system and could resu lt in
damage not covered by your New Vehic le Limited Warra nty. •
Adding coo lant
Be very careful when adding engine coolant.
Before you check anything in the engine compartment,
always read and heed all WARNINGS==> & in "Working in
the engine compartment" on
page 217 .
-Turn off the engin e.
- Let the engine cool down.
Vehic le care I I irechnical data

_____________________________________________ C_h_ e_ c _ k_in --= g'-a _ n_d _ f_il _li _n -=g =-- ____.•
• the engine compartment heats up because the vehicle is parked
in intense sunlight.
& WARNING
• To reduce the risk of personal injury never touch the radiator
fan.
• The auxiliary electric fan is temperature controlled and can
switch on suddenly even when the engine is not running .
• The auxiliary radiator fan switches on automatically when the
engine coolant reaches a certain temperature and will continue to
run until the coolant temperature drops. •
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a quick glance.
Fig. 143 Engine
compartment: brake
fluid reservoir
Before you check anything in the engine compartment,
always read and heed all WARNINGS=> & in "Working in
the engine compartment" on
page 217.
-Read the brake fluid level from the brake fluid reservoir
=> fig. 143. The brake fluid level must be between the
"MIN" and "MAX" markings.
The brake fluid reservoir is located behind the rear partition of the
engine compartment on the left side~ page 218.
The fluid level may drop slightly after some time due to the auto ­
matic adjustment of the brake pads. This is not cause for alarm.
If the brake fluid level falls considerably below the "MIN" mark, the
brake warning/indicator light (U.S. models:
BRAKE, Canadian models:
(Cf))) will come on~ page 19 and~ page 33. Do not continue to
operate the vehicle. The complete brake system should be thor­
oughly checked by an authorized Audi dealer or other qualified
facility and the cause corrected. If the brake fluid level is too low, the
brake warning/indicator light will illuminate. Contact an authorized
Audi dealer
immediately. •
Changing brake fluid
Have the brake fluid changed by an experienced techni­
cian.
Brake fluid absorbs moisture from the air. If the water content in the
brake fluid is too high, corrosion in the brake system may result
after a period of time . The boiling point of the brake fluid will also
decrease considerably and decrease braking performance.
Therefore, the brake fluid must be changed
every two years. Always
use new brake fluid which conforms to Federal Motor Vehicle Stan­
dard "FMVSS 116 DOT 4".
The brake fluid reservoir can be difficult to reach, therefore, we
recommend that you have the brake fluid changed by your autho­
rized
Audi dealer. Your dealer has the correct tools, the right brake
fluid and the know-how to do this for you.
~
Vehic le care I I irechnical data

ffl.___F_ u_ s _ e_s _ a_n _ d_ b_ u_lb _ s _______________________________________________ _
Equipment No.
II Equipment
Amps I
Engine relay, fuel tank control unit, Airbag Off 16 A/C system (control unit) 10
1 light, light switch (switch illumination), diagnos-10
tic connector
17 Tire pressure monitoring system (control unit) 5
18 Not used
2 ABS, ASR, ESP, brake light switch 5
19
Not used
3 AFS headlight (left) 5 20
Not used
Oil level sensor (extended maintenance interval)
(WIVl, tire pressure monitoring system, switch
21 Fuel injectors (gasoline engine) 10
4 for Electronic Stability Program (ESP), AFS head-5 22 Wind deflector (Roadster) 30
lights (control unit), A/C system (pressure sen-23 Horn 20 llsorl, backup light switch
Automatic headlight range control, AFS head -
24 Transmission (control unit) 15
5
light (right)/ manual headlight range control, 5/10 25 Heater rear window Coupe/heated rear window 30/20
halogen headlights Roadster
Control unit for CAN data transfer (gateway),
26 Driver's side power window 30
6 electromechanical steering, automatic transmis-5 27 Passenger's side power window 30
sion shift gate
28 Not used
Acoustic Park Assist, automatic dipping interior
rear view mirror, garage door opener, heatable
29 Washer pump 15
7
windshield washer nozzles, washer pump, wind 5
30 Cigarette lighter 20
deflector relay (Roadster)
31 Starter 40
8
Haldex clutch 5 32 Steering column module 5
9
Control unit Audi magnetic ride 5 33
Instrument cluster 5
Airbag control unit 5 34 Radio navigation system, radio 15
1 1 Mass airflow sensor, crankcase heating 5/10
35
Audio amplifier 30
Door control unit (central locking driver/passen-12 10
36 Engine (control unit) 10 gerl
13 Diagnostic connector 10 37 CAN (Gateway) 5
Rain sensor, automatic transmission shift gate 5 38 Not used
15 Roof light (interior lighting) 5 39 Not
used

_______________________________________________ F_ u_ s_ e_s _ a_ n_d _ b_u_ l_ b _s_--J _
No. Equipm ent Amps
40 Not used
41 Not used
42 Not used
43 Not us ed
44 Not use d
45 Not used
Not used
47 SDARS tuner, cell phone package, TV tune r 5
48 VDA interface
5
49 Not us ed
Fuse location , left side of engine
compartment
"' ~ M 9 -, ., m
F ig . 17 1 Illus tration o f
fu se h old er on l eft s ide
of engin e compart-
m en t: fuses (wi thout
fu se cov er)
Some of the equipment items listed a re optiona l or on ly avai lable on
ce rtain model co nfigurations .
Not e th at the foll owing t able is acc urate at th e tim e of goin g to
pr es s and i s subject to chang e. In the even t of di scr epanc ies, the
lab el on the insi de of th e cove r alwa ys takes pre ced en ce .
•
No . Equipm ent
Fuse h old er (bl ack)
1 Not used
2 Not used
3 Not used
4 Not used
5
II Anti-theft warning system (sensor), anti-theft
warning system (ho rn)
6 Headlamp washer system
7 Electric fue
l pumps (supplyl/volume control
valve
8 Windshield wipers
9 Heated seats (driver and passenger)
10 Lumbar support (driver and passenger
)
1 1 Not used
12 Ventilation b
lower
Fus e holder (brown )
1
2
3
4
5
6
7 Fuel pump (6-cylinderl
02 sensors (6-cylinderl Mass airflow sensor (6 -cy linder)
02 sensors (6-cylin derl
Relay coil relay volum e con tro l valve 14-cylin-
der)
Secondary air pump valve (6 -cylinderl , 02 sen­
so rs ( 4-cylinderl
Positioning valves pre-wired engine harness
Vehicle care Do-it-yourself service
Amps
5
30
15/10 30
25 1 0
40 15
10
5
10
5
1 0
10
-
irechnical data

.,,___F_ u_ s _ e_s _ a_n _ d_ b_ u_lb _ s _______________________________________________ _
No. Equipment Amps
8 Ignition coils (4
-cylinderl/ignition coils (6-cylin -
20/30
der)
9 Engine (control unitl 25
Water pump delayed-off 10
1 1 Feed (clutch pedal, brake pedal) 5
12
Activated charcoal filter/charge pressure con-10 trol valve (4-cylinder)
-' -
Bulbs
Replacing light bulbs
For your safety, we recommend that you have your autho­
rized Audi dealer replace burned out bulbs for you.
It is becoming increasingly more and more difficult to replace
vehicle light bulbs since in many cases , other parts of the car must
first be removed before you are able to get to the bulb. This applies
especially to the light bulbs in the front of your car which you can
only reach through the engine compartment.
Sheet metal and bulb holders can have sharp edges that can cause
serious cuts, and parts must be correctly taken apart and then prop­
erly put back together to help prevent breakage of parts and long
term damage from water that can enter housings that have not been properly resealed.
For your safety , we recommend that you have your authorized Audi
dealer replace any bulbs for you, since your dealer has the proper
tools, the correct bulbs and the expertise.
Gas discharge lamps (Xenon lights)*:
•
Due to the high electrical voltage, have the bulbs replaced by a qual­
ified technician. Headlights with Xenon light can be identified by the
high voltage sticker .
& WARNING
Contact with high-voltage components of the electrical system
and improper replacement of gas discharge (Xenon) headlight
bulbs can cause serious personal injury and death .
• Xenon bulbs are pressurized and can explode when being
changed.
• Changing Xenon lamps requires the special training, instruc ­
tions and equipment .
• Only an authorized Audi dealer or other qualified workshop
should change the bulbs in gas discharge lamps.
& WARNING
There are parts with sharp edges on the openings and on the bulb holders that can cause serious cuts .
• If you are uncertain about what to do, have the work performed
by an authorized Audi dealer or other qualified workshop. Serious
personal injury may result from improperly performed work.
[ i] Tips
• If you must replace the light bulbs yourself, always remember
that the engine compartment of any vehicle is a hazardous area to
work in. Always read and heed all WARNINGS=>
page 209, "Engine
compartment"=>
/A .
• It is best to ask your authorized Audi dealer whenever you need
to change a bulb .•

________________________________________________ E _m_ e_r.:g :;,. e_ n_c ...: y:.- s_ i_ t _u _a_ t_ i_ o _ n_ s __ ffllll
•
& WARNING
• To reduce the risk of serious injury and vehicle damage.
-Always lift the vehicle only at the special workshop hoist and
floor jack lift points illustrated=> page
284, fig. 178 and
=> page 284, fig. 179.
- Failure to lift the vehicle at these points could cause the
vehicle to tilt or fall from a lift if there is a change in vehicle
weight distribution and balance. This might happen, for
example, when heavy components such as the engine block or
transmission are removed.
• When removing heavy components like these, anchor vehicle
to hoist or add corresponding weights to maintain the center of
gravity. Otherwise, the vehicle might tilt or slip off the hoist,
causing serious personal injury.
0 Note
• Be aware of the following points before lifting the vehicle:
- The vehicle should never be lifted or jacked up from under­
neath the engine oil pan, the transmission housing, the front or
rear axle or the body side members . This could lead to serious
damage.
- To avoid damage to the underbody or chassis frame, a rubber
pad must be inserted between the floor jack and the lift points.
- Before driving over a workshop hoist, check that the vehicle
weight does not exceed the permissible lifting capacity of the hoist .
- Before driving over a workshop hoist, ensure that there is
sufficient clearance between the hoist and low parts of the
vehicle. •
Do-it-yourself service