ESP AUDI TT COUPE 2017 Manual PDF

Check ing and F illing
Cooling system
Coolant
The engine coo ling system is filled with a mixture
of pur ified wate r and coolan t addit ive at the fa c­
t ory . T his coo la nt must not be not changed .
The coolant leve l is monito red throug h the . in­
d icator light
c::> page 12. Howeve r, we do recom­
mend occasionally chec king the coo la nt level
manually.
If you must add coolant, use a m ixt ure of wa ter
a nd coo lant add it ive. Mixing the coolant additive
with d istilled water is recommended.
Coolant additive
The coolant additive is made of ant i-freezing and
corros ion protection agents. Only use the fo llow­
ing coolant add it ives. These addit ives may be
m ixed w it h each other.
Coolant additive Specification
G13
TL 774 J
G12++ TL 774 G
The amount of coo lant add itive that needs to be
mixed wit h water depends on the climate where
the vehicle will be operated . If the coolant addi ­
tive percentage is too low, the coolant can free ze
and damage the engine.
Coolant addi- Freeze protec-
tive tion
Warm regions min . 40%, m in. -13 °F
max . 45% (
- 25 °C)
Co ld regions min. 50%, max. -40 °F
max. 55% (-40 °C)
CJ) Note
-Befo re the start of winter, have your author ­
i zed Audi dealer or authorized A udi Service
Fac ility check if the coolant additive in yo ur
vehicle matc hes the percentage approp riate
for the climate . Th is is especially important
whe n driving in co lde r clima tes.
- If the approp riate coolant additive is not
available in an emergency, do no t add any
other addi tive . You cou ld damage the en-
250
gine . If this h appens, on ly use wa ter and re ­
store the correct m ixt ure ratio with t he
specified coo lant ad ditive as soon as poss i­
ble.
- Only refill w ith new coolant .
- Radiator sealant mus t not be mixed wi th
the coolant .
Adding coolant
Fig. 192 En gine co mpar tm ent: coo la nt expans io n ta nk
cove r
-"' -"' •
"" co a,
Observe the safety precautions c::> A in Working
in the engine compartment on page 244 .
Checking the eng ine coolant level
.,. Park your veh icle on a level s urface .
.,. Switch the ignit ion off.
.,. Read the coolant level on the coolant expansion
tank
c::> page 246, fig. 189. The coolant leve l
must be betwee n the markings when the en­
gi ne i n cold . When t he e ng ine is warm it can be
slightly above the uppe r mar king .
Adding coolant
Requirement: there must be a residual amount of
coolant in the expansion ta nk
c::> (D .
.,. Let the engine coo l down.
.,. Place a clot h over the coolant expansion tan k
cap and unscrew the cap counterclockw ise
¢ .&, .
.,. Add coo lant m ixed in the cor rect rat io
c;, page 250 up to t he up per ma rk ing .
.,. Make sure that the fluid level remains stab le.
Add mo re coolan t if necess ary.
.,. Close the cap sec urely .
Coo lant loss usually ind icates there is a lea k. Im-
med iate ly dr ive you r ve hicl e to a n author ized .,.

CD
CD
.... N
" N ...... 0
0
Ill co
Charging the vehicle battery
Fig. 194 Engine compartment: connectors for a charger
and jump start cables
Requirement: only use chargers with a maximum
charging voltage of 30 amps/14.8 Volts.
The
vehicle battery cables remain connected .
.,. Read the warn ings¢
& in General warnings
about batteries on page 252
and ¢ ,& .
.,. Switch off the ignition and all electrical equip­
ment .
.,. Open the hood¢
page 245 .
.,. Open the red cover on the positive terminal
¢fig. 194 .
.,. Clamp the charger terminal clamps to the jump
start pins
according to the instructions
¢fig. 194 .
.,. Now insert the power cable for the charging de­
vice into the socket and sw itch the device on.
.,. At the end of the charging process, switch the
charger off and pull the power cable out of the
socket .
.,. Remove the charger terminal clamps.
.,. Close the red cover on the positive terminal.
.,. Close the hood¢
page 245.
A WARNING
-A highly explosive mixture of gases can form
when charging batteries. Only charge the
vehicle battery in well-ventilated areas.
- A drained battery can freeze at tempera­
tures around 32 °F (0 °C). A frozen or
thawed vehicle battery must not be charged
and must not be used anymore. The battery
housing can crack and battery acid can leak
out if ice forms, which increases the risk of
an explosion and chemical burns . Contact an
Checking and Filling
authorized Audi dealer or authorized Audi
Service Facility for more information.
- Do not connect or disconnect the charging
cable while charging because this increases
the risk of an explosion.
@ Tips
- Only charge the vehicle battery through the
connections in the engine compartment.
- Read all of the manufacturer's instructions
for the charger before charging the vehicle
battery.
Windshield washer system
Fig. 19S Engine compartment: washer fluid reservoir cap
The windshield washer reservoir{!} contains the
cleaning solution for the windshield and the
headlight washer system*¢
page 246, fig. 189.
The reservoir capacity is found in ¢ page 299.
To reduce the risk of lime scale deposits on the
spray nozzles, use clean water with low amounts
of calcium. Always add window cleaner to the wa­
ter. When the outside temperatures are cold, an
ant i-freezing agent should be added to the water
so that it does not freeze.
(D Note
-The concentration of anti-freezing agent
must be adjusted to the vehicle operating
conditions in the respective cl imate. A con­
centration that is too high can lead to vehi-
cle damage.
- Never add radiator anti-freeze or other addi-
tives to the washer fluid. .,.
253

Checking and Filling
-Do not use a glass cleaner that contains
paint solvents, because this could damage
the pa int .
Service interval display
The service interval display detects when your ve­
hicle is due for service.
The service interva l display works in two stages:
- Inspection or oil change reminder: after a cer-
tain distance driven, a message appears in the
Infotainment system display each time the ig­
nition is switched on or off . The remaining dis­
tance or time is displayed briefly.
- Inspection or oil change due: if your vehicle
has reached an inspection or oi l change interval
or both intervals at the same time, the mes­
sage
Inspection due! or Oil change due! or Oil
change and inspection due!
appears briefly af­
ter switching the ignition on/off .
Checking service intervals
You can check the remaining distance or time un­
til the next oil change or next inspection. Select
in the Infotainment system: the !MENU ! button>
Vehicle > left control button > Service & checks >
Service intervals.
{[) Note
-Following the service intervals is critical to
maintain ing the service life and value of
your vehicle, especially the engine. Even if
the mileage on the vehicle is low, do not ex­
ceed the time for the next service.
- Calculating the time to the next oi l change
i s interrupted when the vehicl e battery is
disconnected
~ page 2 79.
254

a, a, ... N
" N ... 0
0
V'> a:,
able to provide you with more in­
formation .
® Mud and snow capability
"M/5" or "M+S" indicates the tire
has properties making it suitable
to drive in mud or snow .
& indi­
cates a winter tire .
@Composition of the tire cord
and materials
The number of plies indicates the
number of rubberized fabric lay­
ers in the tire. In general: the
more layers, the more weight a
tire can carry . Tire manufacturers
must also specify the materials
used in the tire. These inc lude
steel, nylon, polyester and other
materials.
@ Maximum permitted load
This number indicates the max i­
mum load in kilograms and
pounds that the tire can carry.
@ Uniform tire quality grade
standards for treadwear,
traction and temperature resistance
Tread wear, traction and temper ­
ature ranges
¢ page 271.
@ Running direction
@ Maximum permitted
inflation pressure
Wheels
This numbe r ind icates the maxi­
mum pressure to which a t ire can
be in flated unde r normal operat­
ing conditions.
Glossary of tire and loading
terminology
Accessory weight
means the comb ined we ight (in
excess of those standard items
which may be replaced) of auto­
matic transmission, power steer­
ing , power brakes, power win­
dows, power seats, radio, and heater, to the extent that these
items are available as facto ry- in­
s t alled equipment (whether in ­
stalled or not) .
Aspect ratio
means the ratio of the height to
the w idth of the tire in percen t.
Numbers of 55 or lower indicate a
lo w sidewall for improved stee r­
ing response and better overa ll
handling on dry pavement.
Bead
means the part of the tire that is
made of steel wires , wrapped or .,.
257

Wheels
-Have the wheels rebalanced if an imbalance is causing noticeable
vibration in the steering wheel.
If you do not, the tires and other
vehicle components could wear
more quickly.
Treadwear indicator
Original equipment tires contain
treadwear indicators in the tread
pattern, which are bars that are
1/16 in (1.6 mm) high and are
spaced evenly around the tire per­ pendicular to the running direc­
tion¢
fig . 197 . The letters "TWI"
or triangles on the tire sidewall indicate the location of the tread­
wear indicators.
The tires have reached the mini­ mum tread depth
l) when they
have worn down to the tread wear
indicators . Replace the tires with
new ones ¢A.
Tire rotation
Rotating the tires regularly is rec­
ommended to ensure the tires
wear evenly. To rotate the tires,
install the t ires from the rear axle
on the front axle and vice versa .
This will allow the tires to have
1> Obey any applicable regulations in your
country.
264
approximately the same length of
service life.
For unidirectional tires, make
sure the tires are installed accord­
ing to the running direction indi­
cated on the tire sidewall
¢page 286.
Hidden damage
Damage to tires and rims can of­
ten occur in locations that are hidden. Unusual vibrations in the
vehicle or pulling to one side may indicate that there is tire damage.
Reduce your speed immediately.
Check the tires for damage . If no
damage is visible from the out­
side, drive slowly and carefully to
the nearest authorized Audi deal­ er or authorized Audi Service Fa­
cility to have the vehicle inspect­
ed.
8_ WARNING
Tread that has worn too low or different tread depths on the
tires can reduce driving safety.
This can especially have a nega­
tive effect on handling, on the risk aquaplaning when driving
through water, when driving ,..

co
co
.... N
" N .... 0
0
Vl c:o
@ Tips
When using snow chains, it may be useful to
switch on sport mode¢
page 89.
Low aspect ratio tires
Your Aud i is factory-equipped with low aspect ra­
tio tires. These t ires have been thoroughly tested
and been selected specifically for your model for
their supe rb performance, road feel and handling
u nder a va riety of d riving conditions. As k your au­
thor ized Audi dealer for mo re details.
The low aspect ratio of these t ires is indicated by
a numeral of
55 or l ess in the tire's size designa­
tion. The numera l rep resents the rat io of the
tire's sidewall he igh t in relat io n to its tread w idth
expressed in pe rcen tage. Conventional t ires have
a height/w idth rat io of 60 or more .
The performan ce of low -a spe ct-ratio tire s is par­
ticular ly sen sit iv e to improper inflation pre s­
s ur e. It i s therefore import ant that low a spect
ratio tire s are infl ate d to the specified pre ssure
and that the inflation pre ssure i s regularl y
c hecked and mai nta ined . Tir e pre ssure s should
b e che cked at least once a month and alw ay s
before a long tri p ¢
page 265.
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more easi­
ly by impact with potholes, curbs, gullies or
ridges on the road, particularly if the t ire is un­
derinflated .
In order to minimize the occurrence of impact
damage to the tires of your vehicle, we recom­
mend that you observe the follow ing precau­
tions:
- Always maintain recommended inflation pres­
sures. Check your tire pressure every 2,000
miles (3,000 km) and add a ir if necessary .
- Drive carefully on roads with potho les, deep
gul lies or ridges. The impact from driving
t h rough or ove r such obstacles can damage
you r tires. Impact w ith a curb may also cause
damage to your tires.
Wh eel s
- After any impac t, immed iate ly inspect your
tires or have them inspected by the nearest au­ thorized A udi dealer. Replace a damaged tire as
soon as possible.
- Inspect your tires every 2,000 mi les (3,000 km)
for damage and wear. Damage is not a lways
easy to see. Damage can lead to loss of air and
underinflation, wh ic h could eventually cause
tire fa ilure . If you believe that a t ire may have
been damaged, replace the tire as soon as pos­
sible.
- These tires may wear more quickly than others.
- Please also remember that, while these tires
delive r responsive handling, they may ride less
comfortably and make mo re noise than other
choices.
Reduced pe rfo rmance in winter /cold season
conditions
All t ires are des igned for certai n purposes. The
low aspect ratio, ultra h igh performance tires
o rigi na lly installed o n your vehicle are intended
fo r m aximum d ry and wet road per formance and
handling . They are not sui table for co ld, snowy or
icy weather conditions . If you drive under those
circumstances, you should equip yo ur vehicle
with all-season or winter tires, which offer better
tract ion under those conditions. We suggest you
use the recommended snow or all-season tires
specified for your veh icle, or their equivalent.
Refer to¢
page 2 70 for more detailed informa­
t ion regarding winter tires.
Uniform tire quality grading
-T read wear
- Traction AA A 8 C
- Temperature ABC
Quali ty g rades can be fo und whe re applicable o n
the tire side wall between tread sho ulder and
maximum section width
¢page 255, fig. 196 .
For exampl e: Tread wear 200, Traction AA, Tem­
peratu re
A .
All passenger car t ires must conform to Fede ral
Safety Req uirements i n addit io n to these grades . .,,_
271

Wheels
Tread wear
The
tread wear grade is a compara tive ra ting
based on the wear rate of the t ire when tes ted
under contro lled conditions on a specified gov­
ernment test course.
F or examp le, a tire graded 150 would wear one
and one half (11/2) t imes as well on the govern­
ment course as a tire graded 100 .
The rela tive perfo rman ce of t ires depe nds upon
t he act ua l condi tions of their use, howeve r, and
may depart signif icant ly from the norm due to
variations in d riving hab its, service practices and
d ifferences in road characteristics and climate .
T raction
The
tra ction g rades, from highes t to lowes t, are
AA, A, Band
C. T hose gr ades represen t the t ire's
ab ility to stop on wet pavement as meas ured un ­
der controlled conditions on specified govern­ m ent test sur faces of asphalt and conc ret e. A tire
marked C may have poor traction performance
¢ &, .
Temperature The
temperature grades are A (the highest), B,
and C, representing the tire's resistance to the
generation of heat and its ability to d iss ipate
heat when tested under controlled conditions on
a specified indoor laboratory test wheel.
Sustained high temperature can cause the mate ­
rial of the tire to degenerate and red uce tire life,
and excess ive temperature can lead to sudden
tire failure ¢&, .
The gra de C corresponds to a leve l of perform­
ance which a ll passenger ca r tires must meet un­
der the Federa l Moto r Vehicle Safety Standard
No. 109. Grades Band A represent higher leve ls
of performance on the laborato ry test wheel than
the m in imum required by law .
A WARNING
-
The traction grade ass igned to this tire is
based on straight -ahe ad braking t ract ion
t e sts, and does not include a ccele rat ion, cor­
nering, hydrop laning o r peak tract ion charac­
teristics .
272
A WARNING
--
The temperat ure grade for th is tire is estab­
lished for a tire that is properly inflated and
n ot overloaded . Excessive speed, underinfla­
tion, o r excessive load ing, either separately or
in comb ina tion, can ca use hea t bu ildu p and
possib le tire f ailure.
A WARNING
Tempe rature g rades apply to tire s th at are
p rope rly inflated and not over o r underinfla t­
e d.
-
Tire pressure monitoring
system
ill General notes
E ach tire, including the spare (if p rov ided),
shou ld be checked monthly when cold and in flat ­
ed to the inflat ion press ure recommended by the
vehicle manufacturer on the vehicle placard or
tire inflation pressure labe l. (If your veh icle has
tires of a different size than the size ind icated on
the ve hicle placard or tire inflat ion press ure la­
bel, you sho uld dete rm ine the proper t ire infla­
tion press ure for those tires).
As a n added safety feature, your vehicle has been
equipped with a tire pressure mon itor ing system
(TPMS) that illuminates a low tire p ressure tell ­
ta le when o ne or mo re of your tires is s ignificant­
l y unde r-inflated. According ly, w hen the low t ire
pressure tell tale illum ina tes, you sho uld stop and
c h ec k yo ur t ires as soon as possib le, and inf late
t h em to the proper p ressure . Dr iving on a sign ifi ­
cant ly under-inflated tire ca uses the tire to over­
heat and can lead to tire fa ilure. Und er- inflation
also red uces fue l eff iciency and tire tread life,
and may affect the vehicle's handling and stop­
ping ability .
P lease note that the TPMS is not a s ubstitute fo r
proper tire maintenance, and it is the dr iver 's re­
spons ibility to main tain correct t ire pressure,
even if under -in flat io n has not reached the level
to trigge r illumination of the TPM S low t ire pres-
su re te lltale . .,.

co
co
.... N
" N .... 0
0
Vl c:o
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi ­
mately one minute and then remain continuously
illuminated . This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists .
When the malfunction indicator is illuminated,
the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function properly.
If the Tire Pressure Monitoring System
indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction .
Using the ABS sensors, the tire pressure monitor­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires. If the pressure changes in one or more
tires, this is indicated in the Infotainment system
display w ith an indicator light
RE and a message.
If only one tire is affected, the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle
c::;, page 274 . The tire pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
¢ page 265, fig. 199.
Wheels
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if :
- the tire pressure in one or more tires is too low.
- the tire has structural damage.
- the tire was replaced or the tire pressure was
changed and it was not stored
c::;, page 274.
- the spare tire* is installed .
Indicator lights
RE-Loss of pressure in at least one tire c::;, &,.
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
¢ page 274.
mm (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual -If
mm appears after switching on the ignition or
while driving and then the indicator light
RE in
the instrument cluster also starts to blink for
about one minute and then stays on permanent­
ly, there is a system malfunction. Try to store the
correct tire pressures
c::;, page 2 74 . If the indica­
tor light does turn off or turns on again after a short period of time, drive to an authorized Audi
dealer or authorized Audi Service Facility immedi­
ately to have the malfunction corrected.
A WARNING
..-
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.
- The driver is responsible for maintaining the
correct tire pressures . You must check the
tire pressures regularly .
- Under certain conditions (such as a sporty
driving style, winter conditions or unpaved
roads), the pressure monitor indicator may
be delayed.
- Do not use run-flat tires on your vehicle . Us­
ing them when not permitted can lead to
vehicle damage or accidents.
273

Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value.
It can a lso be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dealer or authorized
Audi Service Facility . Read and follow the instruc­
tions for use on the packaging.
A WARNING
- Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i­
son ing .
@ For the sake of the environment
- Preferably purchase env ironmenta lly-friend­
l y cleaning products.
- Do not d ispose of leftover cleaning and care
products with household trash.
Car washes
T he longer that deposits remain on the vehicle,
the more the surface may be damaged. High
temperatures such as those caused by sunlight
increase the damag ing effect.
Befor e washing, rinse
off heavy depos its with
p lenty of water.
S tubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth.
A lso, wash t he un derside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washi ng your ve hicles w ith a pressure
washer, always follow t he ope rating inst ructions
~ p rovided w ith the pressure washe r. This is espe -
;:::: cially important in regard to the pressu re and
" ~ sp raying distance. Do not d irect the stream of 0
~ water directly onto seals for the side windows, c:o
Ca re and cleaning
doo rs, luggage compartment lid or hood or onto
the tires, rubber hoses, insulating materia l, sen­
sors * or camera lenses*. Keep a distance of at
l east 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozz les o r high press ure nozzles .
T he water temperatu re must not be above 140 °F
(60 °().
Automatic car washes
Spray off the vehicle before washing.
Make s ure that the windows are closed and the
windshield wipers a re
off. F o llow instructions
f rom the car wash operator, espec ia lly if there
are accessories attached to your veh icle.
If possible, use car washes that do not have
brushes .
Washing
by hand
Clean the ve hicl e starting from the top and wor k­
i ng down using a soft sponge o r cleaning br ush.
U se solven t-free cleaning produ cts.
Washing vehicles with matte finish paint
by
hand
T o avo id damag ing the pa int w hen washi ng, fi rst
remove dust and large pa rticl es from you r vehi­
cle . Insects, grease spots and fingerprints are
best removed w ith a special cleaner for matte
finish paint.
Apply t he product using a microf iber cloth . To
avoid damaging the paint surface, do not use too
much pressure.
Rinse the ve hicl e thoroug hly w ith wate r. Then
cl ean usi ng a neutral shampoo and a soft micro­
fiber cloth .
Rinse the ve hicl e thorough ly aga in and let it air
dry. Remove any wate r residue using a chamois .
WARNING
- On ly wash the vehicle when the ign ition is
off and follow the instr uctions from the car
275

co
co
.... N
" N .... 0
0
Vl c:o
Care and cleaning
Component Situation Solution
De corat ive p art s/
Deposits Mild
soap so lution al, a cleaning solution suitable for stain-
Tr im less stee l, if necessary
Paint Paint damage Refer to the paint number on the veh icle data label, repair
with touch up pa int
Q page 298
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect
with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv- ice Facility .
Corrosion Have it removed by an authorized Aud i dealer or a uthorized
Aud i Service Fac ility .
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then
apply paint protectant if
paint has been pro -the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith wate r immediately and remove w ith a micro-
sects, bird dropp ings, fiber cloth
tree sap and road
salt
Grease-based con- Remove immediately with a m ild soap solution a) and a
tam inants such as soft cloth
cosmetics or sun-
b loc k
Ca rb on p art s Deposits clean the same way as painted parts Q page 2 75
a) Mild soap solution: maximu m two tablespoons of neutral soap in 1 quar t (1 liter) of water
Interio r cle an ing
Component Situation Solution
W indow s
Deposits Glass cleaner, then wipe dry
De corati ve part s/ Deposits Mild soap solutional
Trim
Pla stic part s
Deposits Damp cloth
Heavier depos its Mild soap solution a), detergent-free plastic clean-
ing solution, if necessary
Displa ys/i nstru-Deposits Soft cloth with LCD cleaner; dust deposits in the
ment clust er lower area of the instrument cluster can be re-
moved using a soft brush.
Co ntro ls Deposits Soft brush, then a soft cloth w it h a mi ld soap solu-
tional
S af ety belts Deposits Mild soap solution al, allow to dry before letting
them retract
277