ignition AUDI TT COUPE 2017 Owners Manual

Instrumen ts and ind icator ligh ts
Instruments and indicator Lights
Instruments
Audi virtual cockpit (instrument cluster)
The instrument cluster is the central information center for the driver.
Fig. 3 Instrume nt cluster overv iew
(D Eng ine coolant temperature 8
@ Driver information system . . . . . . 19
® Fuel level . . . . . . . . . . . . . . . . . . . . 8
@ Trip odometer reset knob . . . . . . . 23
Coolant temperature indicator
The coolan t temperature display c:> page 8,
fig. 3
(D only functions when the ignition is
switched on. To prevent engine damage, p lease
observe the following notes about the tempera­
ture ranges.
Cold rang e
If o nly the L EDs in the left area of the gauge turn
on, the engine has not reached operating tem­
perature yet. Avoid high engine speeds, full ac­
celerating and heavy engine loads .
Normal range
The engine has reached its operating tempera­
ture once the LEDs up to the center of the gauge
turn on . If the . indicator light in the Infotain­
ment system display turns on, the coolant tem­
perature is too high
c:> page 12.
8
(D Note
-Aux iliary head lights and other accessories in
front of the coo ling-a ir intake impa ir the
cooling effect o f the coolant. This increases
the risk of the engine overheating during high outside temperatures and heavy en ­
gine load.
- T he front spoiler a lso helps to distribute
cooling air correctly while driving . If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the eng ine over­
heating w ill increase. See an authorized
Audi dealer or author ized Audi Service Fa­
cility for assistance .
Fuel level
The indicator @ only func tions when the ignition
i s sw itched on. If the fuel level drops below 1.9
gal (7
L), a red LED wi ll light up and the rD indi­
cator light will turn on
c:> page 16 . The LED
blinks red when the fuel level is very low.
The fuel tank capacity of your veh icle is listed in
the
Techni cal Dat a sectio n c:> page 299. ..,_

co
co
.... N
" N .... 0
0
Vl c:o
1111 (USA models ) /. (Canada models )
Brakes : stop vehicle and check brake fluid level
St op the veh icle and check the bra ke f lu id level.
See an au thorize d Au di dealer o r aut ho rize d Au di
Service Faci lity for assistance if necessary .
1111 (USA models) /. (Canada models )
Warning! No brake booster
If brake assist (brake booster) is not wor king , you
h ave to use m uc h mo re fo rce whe n braking the
ve hicl e. See an a uthorized Aud i dea le r or author­
iz ed A udi Servi ce Fa ci lity for assistan ce.
1111 (USA mod els ) /. (Canada models )
Brakes : malfunction ! Stop vehicle safely
If the ABS indicator light fl]) (U SA mode ls) /
ti] (Canada models), the ESC indicator light DJ ,
and the brake system ind icator light 1111 (USA
models)
I . (Canada mode ls) t urn on and th is
message appea rs, the n the ABS, ESC a nd b raking
d istr ibu tio n ar e m alfu nctioning
c:::> _& .
Drive to you r a uthorized Aud i deale r or a uthor­
i zed A udi Service Fac ility immediately to have the
mal funct ion cor recte d
c:::> &.
1111 (USA models) /. (Canada models) Park­
ing brake: malfunction! Safely stop vehicle .
Please contact Service
- If the indicator light and the message appear
when the vehicl e is stationary or after switch­
ing the ignition on ,
check if you can release the
par king b rake. If you ca nnot re lease the par k­
ing br ake, see yo ur autho riz ed Aud i deale r or
a utho rize d Aud i Serv ice Fa cility . If yo u ca n re­
l ease the park ing br ake and t he mess age s till
appea rs, see an au thorized A udi dealer or au­
t h o rized Audi Serv ice Facility immediately to
have the malfunction cor rected .
-If the indicator light and message appear while
driving ,
the hill start assist or emergency b rak­
ing function may be malfunctioning. It may not
be poss ible to set the parking brake or release
i t once it has been set . Do not park your veh icle
on h ills. See a n author ized Audi dealer or au­
thorized Aud i Serv ice Facility fo r ass ista nce.
(USA models): if the
1111 and EiJ indicator
lights tu rn on together, have the brake system
Instruments and ind icator lights
chec ke d imme diately by an au thori zed A udi deal ­
er or authorized Aud i Service Faci lity
c:::> page 15.
T he re is al so a wa rn ing tone w hen the lights tu rn
on .
_& WARNING
-Read and fo llow the warnings in
c:::> page 244, Working in the engine com­
partment
befo re opening the hood and
checking the brake fluid level.
- I f the b rake system indicator li ght does not
turn off or it turns on w hile driving, the
b rake fl uid leve l in the reservo ir is too low,
a nd this increases the risk of a n accident .
S to p t he vehicle and do not co nti nu e d riv­
i n g . See an aut horize d Au di dea le r o r au­
t h oriz ed A udi Se rvi ce Fa cility for assi stan ce.
- I f the b rake system i ndicator light turns on
t oge ther wit h the ABS and E SC indi cato r
lig hts, t he A BS/ES C reg ulat ing fu nction m ay
be mal funct ion in g . Fu nct ions th at sta bilize
the vehicle are no longe r available. This
could c ause the rear of the vehicle to
swe rve, wh ic h increases the risk that the ve ­
h icle will s lide. Drive ca refully to the nearest
author ized Audi dealer or author ized A udi
Serv ice Faci lity and have the mal function
corrected .
PARK/(®)/~ Electromechanical parking
brake
If t he - (U SA mo dels) I. (C an ada models)
indica tor light turns on, t he pa rking brake was
set .
- (USA models) I. ( Canada models) Park­
ing brake: caution! Vehicle parked too steep
If the indicato r ligh t blin ks and the message ap­
pe ars, there is not e noug h braking powe r to se­
cur e the ve hicl e. T he br akes have ove rhe ate d. Th e
vehicle could roll away even o n a sm all i ncline.
- (USA models ) /. (Canada models)
Please press brake pedal to release parking
brake
11

co
co
.... N
" N .... 0
0
Vl c:o
-If the engine oil level is correct and the indica­
tor light still blinks , turn the engine off and do
not continue driving. See an authorized Audi
dealer or authori zed Audi Service Facility for as­
sistance.
The oil pressure warning is not an oil level in­
dicator. Always check the oil level regularly.
0 Generator/vehicle battery
• Electric system: malfunction! Battery is not
being charged
T here is a malfunction in the alternator or the ve­
hicle electrical system.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately. Turn off all un­
necessary electrical equipment because it will
drain the battery . See your authori zed Audi deal­
er or authorized Audi Service Facility if the bat­
tery charge level is too low .
(•) Electrical system: low battery charge. Bat·
tery will be charged while driving
The starting ability may be impaired.
If this message turns off after a little while , the
vehicle battery charged enough while driving.
If the message does not turn off, have an author­
ized Audi dealer or authorized Audi Service Facili­
ty repair the malfunction.
~ Engine stop while driving
• Engine stopped: no power steering or brake
servo possible
There is a malfunction in the engine or in the fuel
supply system .
More force is needed to steer and brake the mov­
ing vehicle when the engine is stopped. If the ve­
hicle is rolling , try to bring it to a stop off to the
side from moving traffic. See an authorized Audi
dealer or authorized Audi Service Facility for as­
sistance .
Instruments and indicator lights
A WARNING
-
If the engine stops while driving, you will
need to use more force to brake the vehicle .
This increases the risk of an accident . There
will still be power steering if the ignition is
switched on while the vehicle is rolling and
there is sufficient battery charge. Otherwise,
you must use greater force when steering.
~ Front safety belt
The. indicator light stays on until the driver's
and front passenger's* safety belts are fastened.
Above a certain speed, there will also be a warn­ ing tone.
@ Tips
For additional information on safety belts,
see
c::> page 189.
C l~ Rear safety belt
Applies to : vehicles with rear safety belt detection
The respective indicator light will turn on briefly
when a safety belt on the rear seats is fastened
or unfastened .
111-If this indicator light turns on briefly, the
safety belt on the rear seat is not fastened.
II-If this indicator light turns on briefly, the
safety belt on the rear seat was fastened.
• -If this indicator light blinks, the safety belt
was unfastened while driving. Above a certain
speed, there will also be a warning tone .
(D Tips
For additional information on safety belts,
see
¢page 189.
~ - Steer ing lock
• Steering: malfunction! Please stop vehicle
There is a malfunction in the electronic steering
lock. You cannot turn the ignition on.
Do
not tow your vehicle because it cannot be
steered. See an authorized Audi dealer or author-
ized Audi Service Facility for assistance.
1111>
13

Instruments and indicator lights
f!II Steering lock: malfunction! Please contact
Service
There is a malfunction in the elect ronic stee ring
lo ck.
Dr ive to an authorized Aud i dea ler or aut horized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
_& WARNING
Do not tow your veh icle when there is a mal­
function in the electronic steering lock -this
increases the risk of an accident.
i'.t Central indicator light
If the . or U indicator light turns on, check
the message in the instrument cluster .
©-Engine start system
• Engine start system: malfunction! Please
c ontact Service
Do not switch the ign it ion off because you may
not be able to switch it on aga in.
D rive to an a uthorized Audi dea le r or a uthorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
II! Engine start system: malfunction! Plea se
c ontact Service
There is a malfunction in the eng ine start ing sys ­
tem.
Dr ive to an a uthorized Aud i dea le r or authorized
Aud i Serv ice Facility immediately to have t he
malfunc tion corrected.
f!. I~ Electronic stabilization control (ESC)
and
( 8 ) anti-lock braking system (ABS)
.
If the DJ indicato r light b links w hile driving, the
E SC or ASR (Anti-S lip Reg ulation) is actively reg u­
lating.
I f the
DJ indicato r light turns on, the system has
switched the ESC off . In this case, you can switch
the ignition off and then on to switch the ESC on
14
again. The in dicator light t urns of f when the sys ­
tem is functioning fully.
Stabi lization control (ESC ): sport . Warning! Re ­
duced stab ility
If the II ind icator light turns o n, ESC sport
mode was switched on using the
I.a OFF I button
~ page 89. You can turn the ESC on aga in by
press the
I ~ OFF ! button ag ain.
Stabilization control (ESC ): off. Warn ing! Re­
duced stability
If the 11 ind icator light turns on, the ESC was re­
str icted or sw itched off using the
I .$ OF F I butto n
~ page 89. The message ESC OFF also appea rs .
You can t urn the ESC o n aga in by p ress t he
l.13 OFF I but to n aga in.
The system switches on when the ignit ion is
switched on . The
II ind icator light turns off
whe n the system is fu nctioning fu lly .
Stabili zation cont rol (ESC ): malfunct ion! See
owner's manual
Stab ilization control (ESC / ABS ): malfunction!
See owner's manual
ABS: malfunction! See owner 's manual
I f the DJ ind ic a tor light and t he A BS indica to r
li gh t
tJ:]) (U SA mode ls)/ riJ (C anada models)
turn on and this message appears, there is a mal ­
function in the ABS system or electronic differen­
tia l lock. Th is also causes the ESC to malfunction.
The brakes still function with their normal power,
but ABS is not active .
Drive to an authorized A udi dealer or authorized
Audi Se rvice Facility immediate ly to have the
malfunction corrected .
_& WARNING
If the 1111 (USA models) • (Canada mod­
e ls) brake system indicator light turns on to ­
ge ther with the ABS and ESC ind icator lights ,
the ABS/ESC regula ting func tion may have
failed. F unctions tha t stabili ze the vehicle a re
no longer ava ilabl e. This could c ause the vehi­
cle to swerve, which inc reases the risk that
the vehicle will slide . Drive ca refully to the
~

co
co
.... N
" N .... 0
0
Vl c:o
nearest authorized Audi dealer or authorized
Audi Service Facility and have the malfunction
corrected.
@ Tips
For additional information on ESC and ABS,
see
~ page 88.
(0) Brake pads
EiJ Brake pads: wear limit reached. You can con­
tinue driving. Please contact Service
The brake pads are worn.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
brake pads checked.
Applies to: USA models
The EiJ indicator light turns on together with the
11111 indicator light
.!f Safety systems
The El indicator light monitors the safety sys­
tems.
Safety system
If them indicator light turns on or blinks, there
is a malfunction in a safety system .
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
_& WARNING
Have the safety systems inspected immedi­
ately. Otherwise, there is a risk that the sys­
tems may not activate during a collision,
which increases the risk of serious injury or death.
c±:, Engine control
-
If the II indicator light turns on if there is a mal­
function in the engine control.
Drive slowly to an authorized Audi dealer or au­
thorized Audi Service Facility to have the engine
checked.
Instruments and indicator lights
o Malfunction indicator lamp (MIL)
The malfunction indicator lamp (MIL) is part of
the On Board Diagnostic system (OBD II). The
¢'4 c;ymbol turns on when the ignition is switched
on and turns off again once the engine is started
and running at a steady idle speed. This indicates
that the MIL is functioning correctly.
The indicator light turns on if there is a malfunc­
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Facility to have the malfunction corrected .
For additional information, see
c::> page 17.
!?i Engine speed lim itation
Applies to: vehicles with engine speed limitation
(II maximum engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects the engine from overheating .
The engine speed limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine control malfunction, the
II indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam­
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im­
mediately to have the malfunction corrected.
~ .. Engine oil level (min. )
II Please check oil level
You may continue driving for the time being.
Check the engine oil level as soon as possible
c::> page246.
-If the engine oil level is too low, add engine oil
~page 248.
- If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility .
15

Drive r inf orm ati on sy stem
- If your vehicle is stationary or if you are driv­
ing at very low speeds, the temperature dis­
played may be s light ly higher than the ac­
tual temperature outside due to the heat
radiating from the engine.
- At temperatures below 41 °F (+S
0
(), a
snowflake symbol appears in front of the
temperature display¢,&.
Multifunction steering
wheel plus
Operating
A pp les to: ve hicles w ith multifunctio n steering wheel p lus
The Multifunction steering wheel plus* hos 14
buttons. You con use them to operate the driver
information system and the MMI functions ,
change the volume and switch the voice recogni­
tion system* on and off.
Fig . 7 Infotainment system display
Fig . 8 Mult ifunc tion steering whee l, left side
Req uirement: the ignition must be switched on.
The driver information system contains mult iple
tabs
(D that display various informat ion @.
The follow ing tabs are available, depending on
veh icle equipment :
20
First tab Vehicle
Second Warnings
tab
a)
Third tab Radio c::> page 150
Media c::>page 155
Fourth tab Telephone*¢ page 114
Fifth tab Navigation
* c::> page 135
Map* c::> page 143
Sixth tab b) Sound¢ page 17 4
Audi connect*¢ page 126
Settings c::> page 174
a) This tab is only visible if at le ast one indicat or light or
message is shown or
if t h e correspond ing system is
switched on.
b) The contents of the tab de pend on the menu that was
used last.
@ Button ~
-Swit ch ing tab s: p ress the l<1 1>I bu tto n to the
left/right (for example, radio).
@ !VIEWI button
S witching th e view : press the !VIEWI button to
switch from the classic v iew
c::> page 19, fig. 5 to
the e nhanced view
c::>page 19, fig. 6.
@button ~
Returning to funct ions at higher levels
@ 121 and 19 contr ol butt ons
Opening/closing the selection menu or options
menu
c::> page 21.
(J) Left thumbwheel
-Sele cting a function in a m enu /list : turn the
left thumbwheel to the des ired function in a
menu or list (such as se lecting a station, Lap
times*) .
-Co nfirming a selection : press the left thumb­
wheel (for example, confirm the station).
-Zoomin g in /out on th e map : when a map is
disp layed, turn the le ft thumbwheel up/down
to zoom in/o ut on the map.

Driver information system
© button l1<1<1 I l1>1>1 I
-Selecting the previous/next tr ack or station :
press the ll1>1I but ton.
- Fast forwarding /re winding audio file s: press
and ho ld the
! 1q<] I or l1>1> 1I bu tton un til t he desired
location in the fi le is reached .
@button @
- Programmable steering wheel button - open ­
ing a function :
press the@ bu tton.
- Programmable steering wheel button - re­
questing a function :
ho ld dow n the Ill button.
- Programmable steering wheel button - chang­
ing a function:
selec t the fi rst tab> Vehicle
settings
> Steering wheel button a ssignment .
@ button 1~·" 1
- Repeating the last navigat ion prompt : press
the
I Q•,.., I button when route guidance is active.
- Changing the voice guidance volume : when
route gu idance is active, turn th e right thumb­
whee l upward or dow nward d uring a navigat ion
prom pt.
Multifunction steering
wheel
Operating
The multifunction steering wheel has four but­
tons. With this feature, you can operate the driv­
er information system and the MMI functions
and you can also change the volume.
Fig . 11 Standard multifunction stee ring wheel
Requirement: the ignition must be switched on.
22
(D Operating the driver information system
The driver information system contains multiple
tabs (!)¢
page 20, fig . 7 that disp lay various i n­
format ion
@ .
The following tabs a re av ail ab le, depe nding on
vehicle e quipment:
l. Tab Vehicle
2. Taba )
Warnings
3. Tab Radio
c::> page 150
Media c::>page 155
4. Tabb )
Sound¢ page 174
Settings ¢page 17 4
a) Thi s tab is only v is ib le if at least one indicator lig ht or
message is shown or if t he co rrespond ing sys te m is
sw itched o n.
b ) Th e co ntents of th e tab depend on the menu t hat was
u se d l ast.
-Switch ing tabs : press th e I MODE I button on the
m ultifunction steering wheel unt il the desired
tab is disp layed .
-Selecting a function in the menu/list : turn the
left thumbwheel on the multifunction steering
wheel to the desired function .
-Confirming a selection : press the left thumb­
wheel on the multifunction steering wheel to
confirm your selection.
-Scrolling with in the lists : turn the left thumb­
wheel on the multifunction steering whee l
quickly to scro ll within the lists .
@!VI EWI button
- Switching the view :
press the IVIEWI button to
switch from the class ic view
c::> page 19, fig. 5
to th e enhanced view c::> page 19, fig. 6.
® Right thumbwheel
The volume o f an a udio source o r a system mes ­
sage (such as traffic announcements) can be di ­
r ectly adjusted during the a udio output.
- Increasing or decreasing the volume : turn the
r ig ht thumbwheel u pward or downwa rd.
- Muting or pausing : turn the rig ht thumbwhee l
downwa rd.
Or : press th e righ t thumbwheel.
- Unmuting or resuming : turn the righ t thumb ­
wheel u pw ard.
Or : press the r igh t thumbwheel.

CD
CD
.... N
" N .... 0
0
Ill co
Tachometer
The tachometer displays the engine speed in rev­
olutions per minute (RPM) .
The beginning of the red zone in the tachometer
indicates the maximum permissible engine speed
for all gears once the engine has been broken in
and when it is warm. Before reaching the red
zone, you should shift into the next higher gear,
choose the Dor S selector lever position, or re­
move your foot from the accelerator pedal.
@ Note
The needle in the tachometer may only be in
the red area of the gauge for a short per iod of
time or there is a risk of damaging the engine .
The location where the red zone begins varies
depending on the engine.
@) For the sake of the environment
Upshifting early helps you to save fuel and re­
duce operating noise.
Odometer
Fig. 12 Instrument cluste r: odomete r and reset button
Trip odometer and odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to measure
short distances .
The trip odometer can be reset to zero by press­ ing the reset button 10.01
r=> fig. 12.
The odometer shows the total d istance that the
veh icle has been driven.
Driver in forma tion system
Malfunction indicator
If there is a malfunction in the instrument clus­
ter,
DEF will appear in the trip odometer disp lay.
Have the malfunction corrected as soon as possi ­
ble.
On-board computer
You can access the following information in the
on-board computer
r=> page 19, fig . 5 @ .
-Time and date ~page 174
-Average consumption
-Range
- Short-term memory overv iew
- Long-term memory overview
The short -term memory collects driving informa­
tion from the time the ignition is switched on un ­
til it is switched off. If you continue driving with·
in two hours after switching the ignition off, the
new values are included when calculating the cur­
rent trip information .
Unlike the short-term memory, the long-term
memory is not erased automatically. You can se­
lect the time period for evaluating trip informa­
tion yourself .
Fuel consumption
The current fuel consumption can be shown us­
ing a bar graph . The average consumption stored
in the short-term memory is also displayed. If
the bar is green, your vehicle is saving fuel
through one of the following functions:
- Recuperation : electrical energy can be stored in
the vehicle battery when the vehicle is coasting or driving downhill. The bar will move toward
CJ .
(D Tips
The date, time of day and time and date for­
mat can be set in the Infotainment system.
23

Opening and clo sin g
@ Key tag with PIN
Only app lies to veh icles with Connec tiv ity serv­
ice*: open the key fob and rub th e PIN unti l it is
visib le. You can activate the Connectivity service*
on your vehicl e using this PIN code.
Replacing a key
If a key is lost, see an authorized Audi dealer or
author ized Audi Service Facility. Have
this key de­
activated . It is important to bri ng a ll keys with
you . If a key is lost, you should report it to your
insuranc e company.
Numb er of keys
You can check the n umber of keys ass igned to
your veh icle in the Infotainment system . To do
this, select : the
I MEN U I button > Vehicl e > left
control b utton
> Service & chec ks > Vehicle in­
fo rm ation .
This way, you can make sure that you
have all the keys when purchasing a used vehicle .
Electron ic immobili ze r
The immobilizer preven ts unauthorized use of
the vehicle .
Under ce rtain c ircumstances, the ve hicle may not
be ab le to start if the re is a key from a differe nt
vehicle manufact urer on the key chain .
Data in the master k ey
When driving, service and maintenance-relevant
data is continuously stored in your remote con­
trol key. Your Aud i service adv isor can read out
this da ta and tell yo u about the wo rk your vehicle
needs . This applies a lso to vehicles with a con ­
ven ience key* .
Personal convenience settings
If two peop le use one vehicle, it is recommended
that ea ch pe rson always uses "t heir ow n" master
key. When the ignition is tur ned off or when the
vehicle is locked, persona l convenience settings
for the follow ing systems are stored and as­
signed to the remote mast er key.
- Clima te contro l system
- Parking a id*
- Active lane assist*
- Side assist*
26
- Drive se lect
The stored settings a re a utomat ica lly recalled
whe n you unlock the vehicle , open the doo rs or
tu rn o n the ignition.
&_ WARNING
Always take the vehicle key with you when
leav ing the veh icle, even for a short period of
time. This applies particularly when chi ldren
remain in the vehicle . Otherwise the children
could start the engine or operate e lectrica l
equ ipment such as power wi ndows.
(D Tips
-
The operation of the remote control key can
be temporarily d isrupted by interference from
transmitters near the vehicle working in the
same frequency range (such as a cell phone or radio equipment) . A lways check if your vehicle
i s locked!
Removing the mechanical key
F ig. 15 Remote control m aste r key : remov ing the mec hani ­
ca l key
.. Press the re lease buttons (!)¢ fig. 15 and re ­
move the mecha nica l key from the remote con ­
trol key .
Using the mec hani cal key, yo u ca n:
- Lock/unlock the g love compar tment .
- Ma nually lock/unlock the vehicle¢
page 30.
-Emergency lock the doors¢ page 30.

Opening and closing
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
Fig. 29 Distance between t he rad iator grille and the re­
mote control transmitter
Programming the button : step 1 on the
control panel
1. Switch on the ignit ion.
2. Press both of the outside buttons on the con­
trol unit¢
page 33, fig. 28 until the yellow
LED @turns off and the green LED@ blinks.
This procedure clears the standard codes that
were set at the factory and does
not need to
be repeated again to program the other but­
tons.
3. Briefly press the button in the control panel
that you want to program.
4. Wait until the yellow LED@blinks. The pro­
gramming mode is active for 5 minutes.
5. Go in front of the vehicle with the original re­
mote control transmitter for the system that
you are programming to the control panel
button.
Programming the button: step 2 at the
radiator grille
6. Ho ld the remote control transmitter at the
vehicle radiator grille¢
fig. 29.
7. Now press the remote control transmitter
until the turn signals on your vehicle blink.
This can take up to 30 seconds.
8. If the emergency flashers blink three times,
the programming was successful.
If the
emergency flashers only b link one t ime, the
five-minute time limit for programming has
expired or the programming was unsuccess­
ful. Repeat the programming starting from
the third step or change the distance to the
radiator grille.
34
9. If the garage door or other systems do not
open with the Homelink buttons even if the
programming was successfu l, the system
may use a rolling code instead of a fixed
code. You must also then perform
rolling
code programming
c:, page 35.
The other two buttons in the control panel can be
programmed using the instructions given above.
Start with step 3.
Deleting button programming
The programmed buttons cannot be deleted indi­
vidually. They must be deleted all at once. Repro ­
gram the buttons if necessary.
.,.. Switch on the ign ition.
.,.. Press both of the outside buttons on the con­
trol unit until the yellow LED @turns off and
the green LED(!) blinks .
Reprogramm ing buttons
.,.. Switch on the ignition .
.,.. To reprogram an individual button, press the
desired button until the green LED @turns off
and the yellow LED@starts to blink (after ap­
proximately 20 seconds). Release the button
immediately. The programming mode is active
for 5 minutes.
.,.. Continue with step 5.
(D Tips
- The distance needed between the remote
control transmitter and the Homelink mod­
ule in the radiator grille
¢fig. 29 depends
on the system you are programming.
- Depending on the system model, you may
need to release the button on the remote
control transmitter while it is programming
and press it again . Hold every position you
try when programming for at least 15 sec­
onds before trying a new position. Keep an
eye on the vehicle turn signals while doing
this.