Rear seat BMW 525i 2001 E39 Repair Manual

Downloaded from www.Manualslib.com manuals search engine
Seats
Remove left and right side bacltrest mounting fasteners (ar-
row).
Pull up on backrest to detach from top retainers. Slide back-
rest to side to clear seat belts while removing.
NOTE-
If the car is equipped with heatedrearseats, detach electrical
harness
connector(s) as you remove the seat components.
4 When reinstalling, be sure to pull seat belts and buckles (ar-
rows) up through appropriate slots in seat cushion.
Headrest, removing and installing
- Slide headrest as far up as possible.
Press guides (arrows)
back and
Installation is reverse of removal pull
upward to remove

Downloaded from www.Manualslib.com manuals search engine
........... General ........................... .72 0.2 Rear Seat Belt Assembly 720-8
......... Troubleshooting ..................... .72 0.2 Rear seat belt assembly (sedan) 720-8
................ Rear seat belts (sedan) 720-9
... .......... Front Seat Assembly '720-4 Rear seat belt assembly (Sport Wagon) 720-9
Front seat belt tensioner,
......... Rear seat belts (Sport Wagon) 720-10
removing and installing ................ .72 0.4
Front seat belt assembly
.............. .72 0.6
Front seat belt reel. removing and
installing (sedan and Sport Wagon models)
.72 0.6

Downloaded from www.Manualslib.com manuals search engine
Seat Belts
NOTE-
The rear bench seat belt strap may not retract fully due to in-
creased friction between strap and seat cover.
A small re-
maining loop in belt strap when fully retracted is acceptable.
WARNING-
* For maximum protection from injury, seat bells should be
replaced as a set (including all hardware), if they are sub-
ject to occupant loading in a collision.
Seat belts should not be modified or repaired. The seat
belt mounting points should not be changed or modi-
fied.
Do not bleach or dye seat belt webbing. Webbing that
is severely faded or
redyed will not meet the strength
requirements of a collision and must be replaced.
Clean belts with a luke-warm soap solution only:
Seat belts should be periodically inspected for webbing
defects such as cuts or pulled threads.
* Immediately after replacing a damaged or worn seat
belt, destroy the old belt to prevent it from being used
again.

Downloaded from www.Manualslib.com manuals search engine
I Seat Belts
a
Front seat belt assembly
1. Seat belt buckle
2. Seat belt stop button
3. Seat belt
4. Seat belt height adjuster
5.
6-pillar cross brace
6. Seat belt reel mounting bolt
7. Seat belt anchor mounting bolt
8. Seat belt lock with pyrotechnic
tensioner
9. Tensioner mounting bolt
Front seat belt reel, removing and installing
(sedan and Sport Wagon models)
- Detach battery negative (-) cable in trunk.
~~-~
Prior to disconnecting the battery, read the battery discon-
nection cautions given in
001 General Warnings and Cau-
l tions. I
- Remove front seat as described in 520 Seats
4 Gently pry up front and rear plastic door sill protector strips
to remove.

Downloaded from www.Manualslib.com manuals search engine
720-8
I Seat Belts
When Installing automatic reel housing to 5-pillar, slide tab
into locating slot (arrow).
Remainder of installation is reverse of removal
Tightening torques
- -.
Front seat to floor (M10) 42 Nm (31 ft-lb)
Seat belt to seat 48 Nm (35 ft-lb)
Seat belt to height adjuster 31 Nm
(23 it-lb)
Seat belt reel to €3-pillar bottom 31 Nm (23 ft-lb)
Sliding height adjuster to €3-pillar
24 Nm (18 ft-lb)
Rear seat belt assembly
(sedan)
1. Center shoulder belt reel
assembly
(if equipped)
2. Right shoulder belt lock
3. Lap-belt assembly
4. Left shoulder belt lock
5. Bolt MlO
(tighten to 31 Nm, 23 ft-lb)
6. Left shoulder belt reel assembly
7. Center shoulder belt lock
(if equipped)
8. Bolt M12
(tighten to 48 Nm, 35 ft-lb)

Downloaded from www.Manualslib.com manuals search engine
-- -
Seat Belts
Rear seat belts (sedan)
- Remove rear parcel shelf to access shoulder belt assembly
mounting bolts. See 513 Interior Trim.
- Remove rear seat cushion to access rear seat belt lock
mounting bolts. See 520 Seats.
- When installing seat belt lock straps:
Install right lock strap (which is shorter) underneath middle
lock strap.
Install left lock strap underneath middle lap belt strap.
Metal strap ends must rest against stop on floor under-
neath seat.
Rear seat belt assembly
(Sport Wagon)
1. BoltMlO
(tighten to 31 Nm, 23 ft-lb)
2. Right shoulder belt reel
assembly
3. Center belt lock
4. Right belt lock
5. Left belt lock
6. Center shoulder belt reel
assembly
7. Left shoulder belt reel assembly
8. Bolt
MI2
(tighten to 48 Nm, 35 ft-lb)

Downloaded from www.Manualslib.com manuals search engine
720-1 0
Seat Belts
Rear seat belts (Sport Wagon)
- Center shoulder belt:
Remove shoulder belt guide trim at top of seat backrest.
Feed belt out through slot in trim. Working in cargo com-
partment, partially remove backrest cover to access shoul-
der belt reel.
Remove shoulder belt reel mounting bolt inside backrest.
- Outboard shoulder belt:
Remove roof-pillar (C-pillar) trim.
Remove center shoulder belt.
- Lift up rear seat cushion(s) to access rear seat belt loclc
mounting
bolt(s).
- When installing seat belt loclc straps:
Install right belt loclc strap (which is shorter) underneath
center belt lock strap.
Install left belt loclc strap underneath center lap belt strap.
- Metal strap ends must rest against stop on floor underneath
seat.

Downloaded from www.Manualslib.com manuals search engine
721 -2
l~irba~ System (SRS)
This repair group covers airbag components and replace-
ment.
Airbag system repairand fault diagnosis is not covered.
Diagnostics, component testing, and
airbag system repair
should be carried out by trained BMW service technicians.
Individual
airbag system components can only be tested elec-
tronically when installed in the car. BMW service testers
DIS
or MoDiC or equivalent must be used for diagnostic work.
WARNING-
Special test equipment is required to retrieve airbag fault
codes, diagnose system faults, and
reseffturn off the air-
bag indicator light. The indicator light will remain on until
any problem has been corrected and the fault memory has
been cleared.
Airbags are part of the BMW Multiple Restraint System
(MRS). Three versions of MRS are available in E39 models.
Multiple Restraint Systems
MRS and MRS II include the following restraint components:
311 996-811 997
911
997-311 999
311 999-2002
Driver and passenger front
airbags (MRSIMRS II)
MRS
MRS
II
MRS Ill
Passenger front two-stage airbag (cars manufactured
from
911998).
The seat occupancy sensor (SBE) is used for detection of
a passenger in the right front seat. MRS uses the SBE in-
put to determine seat belt tensioner
and/or front airbag de-
ployment thresholds.
Side impact
airbag for driver and front passenger
(MRSIMRS II)
Leftlright side impact crash sensors (MRSIMRS 11)
Side impact airbag for rear passenger (MRS II) (optional)
Head Protection System (HPS) for driver and front passen-
ger (MRS
II)
Battery Safety Terminal - BST (MRS II)
Hall Sensor seat belt switches (MRS II)
Front pyrotechnic seat belt tensioners
Fuel pump cut off message

Downloaded from www.Manualslib.com manuals search engine
721 -3
Airbag System (SRS)
MRS Ill adds the following features:
MRS
Ill employs "smart" technology. Smart technology re-
fers to the control module's programming for the deploy-
ment of the airbags, in stages depending on the severity of
the impact.
Two-stage a~rbag for ooln drver and passenger Alloivs for
a softer
c~snioning elfecl when the airbags are lr ggered at
lighter impact,
MRS
Ill satellite sensors use 2 wire connectors
Rear side
airbags arrive de-activated from the factory and
can only be activated upon written request from the cus-
tomer.
Rear seat head protection is available when ordered with
optional rear seat side airbags.
E39 Airbags
Driver airbag
Passenger airbag
Head Protection System (HPS)
Inflatable Tubular Structure
(ITS) (MRS
II and MRS Ill)
Front side impact airbag
Rear door side impact airbag
(optional) (MRS I1 and MRS Ill)

Downloaded from www.Manualslib.com manuals search engine
Airbag System (SRS)~
MRS control module, replacing
- Disconnect negative (-) cable from battery and cover nega-
tive terminal with insulating material.
CAUTIOI\C
Prior to disconnecting the battery, read the battery discon-
nection cautionsgiven in001 General Warnings and
Cau-
tions.
- Remove center console between front seats. See 513 lnteri-
or Trim.
Remove module mounting nuts (arrows) and lift up control
module. Disconnect electrical harness connector.
Installation is reverse of removal.
Be sure that MRS control module ground cable is attached
to the module mounting stud.
Side-impact crash sensor, removing and
installing
- Make sure ignition key is OFF.
- Remove front seat. See 520 Seats.
Remove plastic door sill trim by lifting to release clips at one
end, then sliding off. Fold up carpet towards rear seat floor. If
necessary, remove floor level heater duct.