open BMW 528i 2001 E39 Workshop Manual

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate
Rear window and tailgate, alignment
- Alignment procedures involve adjusting tailgate, window, and
spoiler to have equal space between
iefl and right sides and
to be flush with body. Measurement locations and specific di-
mensions are shown.
- If alignment has been disturbed during repair, adjust fit of tail-
gate to body. Then adjust fit of rear window to tailgate.
Clearance of the rear window is adjusted by adding or re-
moving shims between hinge bracket and rear window
(maximum of three shims).
Adjust spoiler gap to body last.
Height of spoiler is set by alignment of the rear tailgate.
Gap of spoiler to body is set by adjusting spoiler attach-
ment fasteners.
- Lateral and vertical alignment of the window and tailgate is
done using hinge bolts. Fine adjustment of the tailgate to the
body is made using rubber stop buffers and latch assembly.
Spoiler gap specification Rear spoiler to roof 4.25
- 5 mm
(0.167 - 0.197 in)
Max. deviation from parallel 0.5
mm (0.019 in)
Tailgate alignment, preliminary work
- Open rear window and tailgate.
< Remove lower sill trim panel fasteners covers (arrows) and
fasteners.
- Remove rear window and tailgate trim panel.
- Checlc left and right side lateral guides and tailgate latch ful-
crums for wear or damage. Replace
if necessary.

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, ~ail~atel
4 Loosen lower tailgate lock fasteners (arrows) so that tailgate
lock can center itself.
CAUTION-
The lower section of tailgate lock must not scrape against
the upper section.
The eccentric pin on the lower section of the tailgate
loclc rotates
when being locked from upper section of
tailgate lock.
- Disconnect tailgate latch actuator motor by squeeze locking
tabs on electrical harness connector and disconnecting.
CAUTION-
Eccentric pin in lower section of trunk lid lock must be at
lower dead center.
After disconnecting plug connector from actuator mo-
tor, tailgate is opened by electric
unloclcing fixture of up-
per section of tailgate loclc.
. For this reason, the cable connections to the upper
section of the tailgate loclc must remain connected.
Othe~tise the tailgate can only be opened by the emer-
gency handle. Eccentric pin of lower section of tailgate
loclc remains at bottom dead center point after unlock-
ing.
Tailgate alignment, height adjustment
4 Loosen left and right tailgate hinge fasteners (arrows) to al-
low tailgate to be adjusted.
CAUTION-
. When the hinge screws for the tailgate are released, the
position of the overall assembly changes with respect to
the body.
The position of the rear window frame to the tailgate re-
mains unchanged.
- Close tailgate carefully and check gap dimensions. See Tail-
gate alignment specifications below.
- Tighten hinge screws when gap dimensions are correct.

Downloaded from www.Manualslib.com manuals search engine
41 2-1 8
Trunk Lid, Tailgate
Tailgate gap and length adjustment
- Close tailgate and open rear window.
Loosen left and right tailgate hinge
bracket fasteners (ar-
rows)
to allow movement of tailgate.
CAUTION-
When the hinge bracket fasteners are loosened, the posi-
tion of the rear window frame changes with respect to the
tailgate.
Always
check the settings of the rear window frame to
the tailgate and
make adjustment if necessary
NOTE-
The tailgate should be approximately I mm lower then side
walls.
4 To obtain tailgate to body parallel alignment, top edge of tail-
gate must first be adjusted parallel to the edge
of D-pillar (A).
I D-pillar gap 27 rnrn (1.6 in)/
- Adjust gap with window open and tailgate closed.

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate
4 Tighten left and right tailgate bracket iasteners (arrows)
4 Tighten upper left and right tailgate fasteners (arrows).
- Open tailgate while taking care not to change hinge posi-
tions.
4 Tighten lower tailgate hinge fasteners (arrows)
- Reconnect eccentric pin actuator motor electrical harness
Plug.
CAUTION-
The eccentric pin in the lowersection of the tailgate loclc turns
in the tailgate when the button is pressed.
- Operate button in tailgate to actuate loclting motor. Eccentric
pin should move to top dead center position.

Downloaded from www.Manualslib.com manuals search engine
Trunk Lid, Tailgate
4 To periorm contact pattern test, coat lower latch areas A, 6
and C with grease.
Carefully close and reopen tailgate.
Check that upper section of tailgate lock does not scrape
against lower latch.
* Eccentric pin in lower section of tailgate loclc must not
scrape against upper section
(B) of tailgate lock.
The contact pattern (C) of upper section of tailgate lock on
eccentric pin should be centered.
- To adjust height of upper section of tailgate lock, loosen fas-
teners, move upper section of lock and retighten fasteners.
Repeat contact pattern test after height adjustment.
Tailgate lateral guide, adjusting
< If necessary, loosen lateral guide to body fasteners (arrows)
to allow it to move.
Move lateral guides to center position.
< Loosen lateral guide to tailgate fasteners to allow it to move.
- Close tailgate to center guides with respect to each other.
NOTE-
The bracket of the lateral guide continues to touch against
the body without clearance as does the lateral guide against
the tailgate.
- Open tailgate and tighten guide fasteners.

Downloaded from www.Manualslib.com manuals search engine
41 2-21
Trunk Lid, ~ailaatel
Rear window, adjusting
NOTE- Three versions of rear window are used on
Sport Wagon
models.
Tailgate must be correctly adjusted before rear window ad-
justments are made.
- . . . . . .. .. 4 With tailgate closeo ano rear window open, oosen ninge fas-
teners (arrows) to allow ninge to move.
- LoosL'n fasteners n lower section of ock to al ow movement.
- Care& ly c ose rear window:
Ad.~st gap dmensions and poston of rear window relative
to Oody panel. See Tailgate alignment specifications. .
FA-UTION- I
On transition area between rooflailgate, tailgate must not ex-
tend above height of roof
othe~lise wind noise will be creat-
ed.
- If necessary, adjust height of rear window frame by inserting
spacers between the hinge and the frame.
- Carefully open rear window, taking care not to alter adjust-
ment.
Tighten left and right rear window fasteners.
Close rear window and check adjustment, repeat step if
necessary. See Tailgate alignment specifications.
Rear window locking pin, adjusting
NOTE-- Several versions of rear window
locldng pin are used on
Sport Wagon models.
1999 528i model is shown. Other
models are similar.
For rear window adjustment specifications,
seeTailgate
alignment specifications.
Loosen lower assembly fasteners (arrows)

Downloaded from www.Manualslib.com manuals search engine
41 2-22
1 Trunk Lid, Tailgate
4 With rear window open, loosen loclc nut (A) so that inclination
of loclting pin
(B) can be adjusted.
- Carefully close rear window, while ensuring that locking pin
is centered in rotary latch in lower section.
NOTE-
When closing rear window, be sure that there is a gap of ap-
proximately
1 mm (0.04 in) between the locliing pin and the
rotary latch in the lower section of lock.
- Open tailgate and tighten lower loclc assembly fasteners. Be
careful not to alter inclination of loclting pin
(B) when tighten-
ing loclc nut
(A).
4 To adjust height of rear window at lock, loosen loclc nut (A)
and turn locking pin (B).
Be careful not alter position of loclting pin when tightening
lock nut
(A).
CA UTIOG
After adjusting rear window, always checlr position of wiper
axis relative to drive disc and limit stop on rear window wiper
motor. Adjust if necessary See 611 Wipers and Washers.

Downloaded from www.Manualslib.com manuals search engine
Exterior Trim, ~umpersl
4 While supporting mirror, remove top mounting fastener
(arrow).
Lifi mirror up to remove from door, feed mirror electrical
harness through opening to remove.
- Installation is reverse of removal.
NOTE-
Checlt mirror function before installing covering parts.
Tightening torque
Outside mirror to door (M6) 6 Nm (4.5 It-lb)
BUMPERS
- Raise and properly support vehicle.
WARNING-
Male sure that the car is firmly supported on jacltstands de-
signed
forthe purpose. Place the jacltstands understructural
cliassis points. Do not place
jack stands under suspension
oarfs.

Downloaded from www.Manualslib.com manuals search engine
51 0-1 0
Exterior Trim, Bumpers Rear bumper, removing
and installing
Remove expansion rivets from rear inner fender well panels
(arrows).
Working in luggage compartment:
Raise spare tire cover.
- Remove trim panel covering luggage compartment latch.
Open battery cover trim panel on right side and luggage
compartment.
Open left side trim panel.
4 Remove expansion rivets (arrows) from rear panel.
Remove left and
remove panel. right
side panel mounting
nuts (arrow) and

Downloaded from www.Manualslib.com manuals search engine
Exterior Trim, Bumpers 1
Radiator grill, removing and installing
- Open hood
4 Carefully pry out tab on lefl or right side of grill trim ring (A),
as well as tabs on bottom.
- Push grill out through opening. Be careful of hood lever on
passengers side of grill.
- Once grill is removed, pry remaining tabs (B) to separate in-
ner grill from chrome trim ring.
- Before installation, assemble chrome trim ring and grill insert
securely. Replace components
if tabs or catches are brolten
or missing.
- Install grill and trim ring in appropriate location in hood. Press
on trim ring until grill snaps into place.
Headlight housing trim panel, removing
and installing
4 Open hood
- Remove spray nozzle of vehicles equipped with headlight
cleaning systems. See
611 Wipers and Washers.
Release inner tab (arrow) support.
Swing trim out to release outer hook
point. from fender mounting
Installation is reverse of removal