change time BMW 530I 1998 E39 Central Body Electronics ZKE Manual

Vehicle Memory: The owner is provided with a list of available system functions that can
be customized to their liking. Prior to delivery, the DISplus or MoDiC is used to encode the
owner’s chosen selections into the appropriate control modules.
These choices become a permanent function of the control module and can only be
changed by re-encoding with the DISplus or MoDiC at a BMW Center.
This feature has been available for some time via the ZCS Conversion Feature but has
never been fully utilized or officially presented to the vehicle owner as a feature of their vehi-
cle.
Key Memory: This feature provides the added convenience of identifying users of the vehi-
cle whenever a lock or unlocked signal is generated via the individual FZV keys. A maxi-
mum of four FZV keys can be used with the Key Memory feature.
Each of the four keys generate a unique key identification signal (key number) that is trans-
mitted simultaneously with the lock/unlock signals to the General Module. Key Memory
does not respond to Lock/Unlock requests from the drivers door lock.
Mostof the key memory functions require the vehicle be configured using the “KEY MEM-
ORY” function of the DIS or MoDiC. However, there are a few features that store settings
automatically without configuration such as IHKA blower speed and temp setting. The key
ID signal alerts the GM to communicate with select control systems over the K Bus to store
(when locked) or reset (when unlocked) certain driver adjustable settings.
There are features that function as both a Car & Key Memory feature.
Example; the Automatic Seat Adjustment feature is encoded as a Car Memory Function
with the following possibilities:
• When unlocking,
• When opening a door after unlocking
• Or not active at all.
If active, the seat positions are stored and reactivated by the Key Memory function for indi-
vidual users of the car.
Notes: _______________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
28
Central Body Electronics ZKE III

System Components
Interior Sensor FIS (up to 99 MY): The interior sensor is mounted in the center of the
headliner panel. Due to the design of the vehicles interior, the sensor is uni-directional and
must be installed in the proper direction to ensure proper operation of the system.
When the alarm system is armed, the sensor emits electromagnetic waves at a frequency
of 2.45 GHz. As long as nothing is moving in the vehicle, the waves as bounced back to
the sensor at the same frequency. The sensor monitors these bounced back waves as an
indication that nothing is disturbed within the vehicle.
If a foreign object enters the vehicle, the frequency of the bounced back signal changes.
The sensor monitors the changed frequency and triggers the alarm.
Every time the DWA system is armed, the
sensor adapts to what ever objects might be
stationary in the interior.
This allows packages or objects to be left
inside the car without effecting the operation
of the system. The sensitivity of the sensor is
set so that the moving object must be at least
as large as a bumble bee. This prevents a
false alarm from occurring from small insects
that might be caught in the vehicle.
The FIS is switched OFF when the vehicle is locked two times within ten seconds. The LED
will flash one time for confirmation. This allows the sensor to be switched OFF to avoid false
alarms when the windows are left open for venting.
34
Central Body Electronics ZKE III
615200103.eps615200104.eps

Interior Sensor UIS (after 99 MY):Similar to the FIS, the UIS monitors the vehicle interi-
or for motion. The UIS uses ultrasonic sound wavs instead of microwaves (less suceptable
to magnetic interference). The UIS is a combined transmitter and receiver.
The interior sensor is mounted in the center of the headliner panel. Due to the design of the
vehicles interior, the sensor is uni-directional and must be installed in the proper direction
to ensure proper operation of the system (trim cover ensures directional installation).
Every time the DWA system is armed (signal STDWA), the sensor adapts to what ever
objects might be stationary in the interior. The sensor emits ultra sonic waves in a pro-
grammed timed cycle. It receives echos of the emitted waves.
The UIS amplifies the received sound wave signals and compares them with the transmit-
ted waves. The UIS also checks the incoming echos for background hiss (wind noise
through a partially open window) and adapts for this.
• If the echos are consistently similar, no movement is detected.
• If the echos are altered, (inconsistent), the UIS determines motion in the interior com-
partment.
If motion is detected, the UIS changes to a constant cycle and the echo is compared again.
If the inconsistency is still present the UIS sends the activate siren signal (INRS) to the GM.
The UIS is switched OFF when the vehicle is locked two times within ten seconds. The LED
will flash one time for confirmation. This allows the sensor to be switched OFF to avoid false
alarms when the windows are left open for venting.
35
Central Body Electronics ZKE III
615200105.eps

Tilt Sensor (Liquid Type - E38/E39 to 97 MY): The Tilt Sensor consists of a conductive
liquid chamber, a processor board and metal probes (located in the luggage compartment).
The probes are submersed in the liquid and produce a resistance value dependent on the
tilt of the sensor (angle of vehicle). This resistance value becomes the static point when the
DWA System is armed.
If the vehicle is jacked-up or lifted,
the angle of the liquid changes
producing a change in the resis-
tance value. The sensor recog-
nizes this change and signals the
GM to activate the DWA alarm.
The resets at the new angle. This
allows the DWA to remain armed
and re-activate the alarm if the
vehicle is moved again.
As with the interior sensor, the tilt sensor is also switched OFF when the vehicle is locked
two times within ten seconds. The LED will flash one time for confirmation. This allows the
sensor to be switched OFF for transportation purposes.
Tilt Sensor (Electronic Type from 98 MY): Located in the luggage comparment area,
the tilt sensor is an electronic sensing device with the sole purpose of monitoring the vehi-
cle's parked angle when DWA is armed.
The sensor requires three signal wires to func-
tion:
• KL 30 - Constant battery voltage
• Signal "STDWA"; switched ground input sig-
nal provided by the GM indicating DWA
armed/disarmed status.
The tilt sensor is used as a splice location for
the STDWA signal to the Siren and UIS int-
erior protection sensor.
36
Central Body Electronics ZKE III
625200107.eps

• Signal "NG"; switched ground output signal provided to the GM. The signal is used for
two purposes,
1. As a momentary acknowledgment that the tilt sensor received STDWA and is cur-
rently monitoring the vehicle angle.
2. If the tilt sensor detects a change in the vehicle's angle when DWA is armed, signal
NG is switched to inform the GM to activate the siren.
When the tilt sensor receives the STDWA signal from the GM it memorizes the vehicle's
parked angle. The angle of the vehicle is monitored by the solid state electronics. Once
armed, if the angle changes, the tilt sensor provides a switched ground signal to the GM
to activate DWA.
As with the interior sensor, the tilt sensor is also switched OFF when the vehicle is locked
two times within ten seconds. The LED will flash one time for confirmation. This allows the
sensor to be switched OFF for transportation purposes.
Glass Breakage Sensors (Early E38 - before FIS Sensor): The door windows (includ-
ing the rear quarter glass wire loop) are monitored by inductive sensors mounted on the
inside of the door behind the trim panel. A closed window is recognized by a magnetic plate
on the glass lining up with the sensor.
If the glass is broken, the plate falls away and the signal from the sensor changes and the
GM will activate the alarm.
Alarm Siren: The alarm siren is mounted in the rear wheel well, behind the inner wheel
housing cover (early E38 used an alarm horn). The E53 alarm siren is located in the left side
of the engine compartment.
The siren contains electronic circuitry for producing the warn-
ing tone when the alarm is triggered. The siren also contains a
rechargeable battery that is used to power the siren when the
alarm is triggered.
The rechargeable battery will allow the siren to sound if it or the
vehicle’s battery is disconnected. The siren battery is
recharged, from the vehicle’s battery, when the alarm is not in
the armed state.
37
Central Body Electronics ZKE III
625200108.eps

Interior Lighting
Purpose of the System
The GM controls the interior lighting automatical-
ly with the status change of several monitored
inputs. The lighting can also be manually con-
trolled using the interior light switch.
In addition to the various time controls, the inte-
rior lights are also subject to the 16 minute shut
down of the GM (consumer protection).
Principle of Operation
The interior light switch is a push button switch that will carry out the opposite command
of the current status of the lights. (ie: if the interior lights are currently on, pushing the but-
ton will switch the lights off.)
• If the interior lights are switched “ON” by the button with the ignition switched ON, the
interior lights will remain on until they are switched off by the button.
• If the interior lights are switched “ON” when the ignition is switched OFF, the lights will
remain on for 16 minutes (consumer cutout).
• Pressing the interior light button for longer than three seconds will switch the lights to
continuous off. This feature is intended for workshop use.
Pressing the button again will
return the lights to the normal operational status.
• Locking the vehicle from the outside will immediately switch off the interior lights.
The ON/OFF conditions for the interior lights in the automatic mode are as follows:
ON Conditions
• Door Open.
• Switching off ignition after exterior
lights have been switched off.
• MRS Control Module crash input.
• Unlocking with FZV or pressing FZV
lock button when the vehicle is
already locked (interior search fution).
51
Central Body Electronics ZKE III
OFF Conditions
• All doors closed with ignition on.
• All doors closed with ignition off after 20
seconds.
• 20 seconds after switching off ignition with
lights off.
• 8 seconds after remote control activation.
• 16 minutes with door(s) open.
• When doors are locked.

59
Central Body Electronics ZKE III
System Components
- with Principle of Operation
Manual Operation:The manual adjustments of the seat, mirrors and steering column are
carried out with the respective switches as with the previous systems.
The mirror adjustment switch is located in the driver’s switch block. The mirror operation
input is a digital signal that is processed by each respective module for mirror positioning.
Memory Storage: The parameters for storing memory positions are are as follows:
• With the transmission range
selector in “P” and the mirror
change over switched to the left,
switch the ignition on and press
the “M” on the memory switch.
• The memory indicator lamp swi-
tches on for 7 seconds.
• Press one of the three position
switches (1, 2 or 3) within the 7
second memory period.
• The current positions of the mir-
rors, seat and steering column
are stored for recall.
The positions of the mirrors are stored in the respective door
modules based on the position of the feedback potentiome-
ters. The positions of the seat and steering column are stored
in the seat module, based on the ripple count.
Recalling a memory position setting is possible by either
pressing and holding the recall switch (1, 2 or 3) with KL 15
“ON” or tapping the recall button (1, 2 or 3) with:
• The driver’s door open and KL 15 “OFF”.
• KL R ON and KL 15 “OFF”.
The recall movement can be interrupted at any time by touching any of the adjusting
switches.
E38/E39
E53
615200133.tiff

Comfort Seats (standard on E38 750iL, other models if equipped)
This option provides additional back support in the
shoulder area. An additional adjustment in the upper
backrest allows forward “contour” that is controlled by
a rocker switch in the side panel.
When the ignition is on or off, the two way rocker switch
can be pushed until the desired setting is achieved (for-
ward/backward tilt). The motor drive operates the same
as the seat motors.
The shoulder support adjustment is also stored in
memory for recall.
Active Seat (E38 - if equipped)
Purpose of the System
Actively changing the surface of the seat helps to prevent muscle tension and fatigue par-
ticularly on long trips or sitting in one position for a long period of time. The seat causes
weight transfers which are slight and imperceptible enhancing driving comfort. The basic
seating position is not changed by this.
In the seat’s upholstery beneath the surface of the seat is a cushion of fluid on the left and
right. The fluid is slowly circulated back and forth between the cushions by a pump.
65
Central Body Electronics ZKE III