rear view mirror BMW ACTIVE HYBRID 7 2013 F04 User Guide
[x] Cancel search | Manufacturer: BMW, Model Year: 2013, Model line: ACTIVE HYBRID 7, Model: BMW ACTIVE HYBRID 7 2013 F04Pages: 253, PDF Size: 5.01 MB
Page 129 of 253

▷Arrows: at least one lane marking was de‐
tected and warnings can be issued.
Issued warning
If you leave the lane and if a lane marking has
been detected, the steering wheel begins vi‐
brating.
If the turn signal is set before changing the
lane, a warning is not issued.
End of warning
The warning ends:
▷Automatically after approx. 3 seconds.▷When returning to your own lane.▷When braking hard.▷When using the turn signal.
System limits
The system may not be fully functional in the
following situations:
▷In heavy fog, rain or snowfall.▷In the event of worn, poorly visible, merg‐
ing, diverging, or multiple lane markings
such as in construction areas.▷When lane markings are covered in snow,
ice, dirt or water.▷In tight curves or on narrow lanes.▷When the lane markings are covered by
objects.▷When driving very close to the vehicle in
front of you.▷When driving toward bright lights.▷When the windshield in front of the interior
rearview mirror is fogged over, dirty or cov‐
ered with stickers, etc.▷During calibration of the camera immedi‐
ately after vehicle shipment.Active Blind Spot Detection
The concept
Two radar sensors below the rear bumper
monitor the area behind and next to the vehicle
at speeds above approx. 30 mph/50 km/h.
The system indicates whether there are vehi‐
cles in the blind spot, arrow 1, or approaching
from behind on the adjacent lane, arrow 2.
The lamp in the exterior mirror housing lights
up dimly.
Before you change lanes after setting the turn
signal, the system issues a warning in the sit‐
uations described above.
The lamp in the housing of the exterior mirror
flashes and the steering wheel vibrates.
Notes Personal responsibility
The system does not serve as a substi‐
tute for the driver's personal judgment of the
traffic situation.
Be aware of the traffic situation and the vehi‐
cle's surroundings at all times, otherwise an
accident is still possible despite all warnings.◀
Seite 125SafetyControls125
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 141 of 253

The arrangement of the buttons varies accord‐
ing to the how the vehicle is equipped or coun‐
try-specific variants.
Radar sensor
A radar sensor is located in the front bumper
for detecting vehicles on the road ahead of the
vehicle.
A dirty or covered sensor may hinder the de‐
tection of vehicles.
▷If necessary, clean the radar sensor. Re‐
move layers of snow and ice carefully.▷Do not cover the view field of the radar
sensor.
Camera
The camera is located near the base of the
mirror.
Keep the windshield in the area behind the in‐
terior rearview mirror clean and clear.
Switching on/off and interrupting cruise control
Switching on Press the button on the steering
wheel.
The indicator lamps in the instrument cluster
light up and the marking in the speedometer is
set to the current speed.
Cruise control can be used.
Switching off Deactivated or interrupted system
If the system is deactivated or inter‐
rupted, actively intervene by braking, steering
and, if necessary, with evasive maneuvers; oth‐
erwise, there is the danger of an accident oc‐
curring.◀
If switching off the system while stationary,
press on the brake pedal at the same time.
Press the button on the steering
wheel.▷If active: press twice.▷If interrupted: press once.
The displays go out. The stored desired speed
and distance are deleted.
Interrupting Press the button on the steering
wheel.
If interrupting the system while stationary,
press on the brake pedal at the same time.
The system is automatically interrupted in the
following situations:
▷When the brakes are applied.▷When transmission position D is disen‐
gaged.▷When DTC Dynamic Traction Control is
activated or DSC is deactivated.Seite 137Driving comfortControls137
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 155 of 253

System limits
The cameras capture a maximum range of
330 ft/100 m.
Top View
The concept Top View assists you in parking and maneu‐
vering. The area around the doors and the road
area around the vehicle are shown on the Con‐
trol Display for this purpose.
General information
The image is captured by two cameras integrated in the exterior mirrors and by the
backup camera.
The range is at least 7 ft/2 m to the side and
rear.
In this way, obstacles up to the height of the
exterior mirrors are detected early.
Notes Check the traffic situation as well
Check the traffic situation around the ve‐
hicle with your own eyes. Otherwise, an acci‐
dent could result from road users or objects lo‐
cated outside the picture area of the
cameras.◀
At a glance
Button in the vehicleTop View
Cameras
The lenses of the Top View cameras are lo‐
cated at the bottom of the exterior mirror hous‐
ings. The image quality may be impaired by
dirt.
Clean the lens, refer to page 230.
Switching on/off
Switching on automatically Select transmission position R with the engine
running.
The Top View and PDC images are displayed if
the system is switched on via iDrive.
Automatic deactivation during forward
travel
The system switches off when a certain driving
distance or speed is exceeded.
Switch the system back on if necessary.
Switching on/off manually Press the button.
▷On: the LED lights up.▷Off: the LED goes out.
Top View is displayed.
Seite 151Driving comfortControls151
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 156 of 253

Switching on the backup camera via
the iDrive
With Top View switched on:
"Rear view camera"
The backup camera image is displayed. The
setting is stored for the remote control cur‐
rently in use.
Display
Visual warning The approach of the vehicle to an object can
be shown on the Control Display.
When the distance to an object is small, a red
bar is shown in front of the vehicle, as it is in
the PDC display.
The display appears as soon as Top View is
activated.
If the rearview camera image was selected last,
it again appears on the display when reverse
gear is selected. To switch to Top View:
"Rear view camera" Select the symbol on
the Control Display.
The setting is stored for the remote control
currently in use.
Brightness
With Top View switched on:
1. Select the symbol.2.Turn the controller until the desired setting
is reached, and press the controller.Contrast
With Top View switched on:1. Select the symbol.2.Turn the controller until the desired setting
is reached, and press the controller.
Displaying the turning circle and
pathway lines
▷The static, red turning circle line shows the
space needed to the side of the vehicle
when the steering wheel is turned all the
way.▷The variable, green pathway line assists
you in assessing the amount of space ac‐
tually needed to the side of the vehicle.
The pathway line is dependent on the cur‐
rent steering angle and is continuously ad‐
justed with the steering wheel movement.
"Parking aid lines"
Turning circle and pathway lines are displayed.
System limits
Top View cannot be used in the following sit‐
uations:
▷With a door open.▷With the trunk lid open.▷With an exterior mirror folded in.▷In poor light.
A Check Control message is displayed in some
of these situations.
Seite 152ControlsDriving comfort152
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 171 of 253

Interior equipmentVehicle equipmentAll standard, country-specific and optional
equipment that is offered in the model series is
described in this chapter. Therefore, equip‐
ment is also described that is not available in a
vehicle, e. g., because of the selected optional
equipment or country variant. This also applies
for safety-related functions and systems.
Integrated universal remote
control
The conceptThe integrated universal remote control can
operate up to 3 functions of remote-controlled
systems such as garage door drives or lighting
systems. The integrated universal remote con‐
trol replaces up to 3 different hand-held trans‐
mitters. To operate the remote control, the
buttons on the interior rearview mirror must be
programmed with the desired functions. The
hand-held transmitter for the particular system
is required in order to program the remote con‐
trol.
During programming
During programming and before activat‐
ing a device using the integrated universal re‐
mote control, ensure that there are no people,
animals, or objects in the range of movement
of the remote-controlled device; otherwise,
there is a risk of injury or damage.
Also follow the safety instructions of the hand-
held transmitter.◀
Before selling the vehicle, delete the stored
functions for the sake of security.Compatibility
If this symbol is printed on the packag‐
ing or in the instructions of the system
to be controlled, the system is gener‐
ally compatible with the integrated universal
remote control.
If you have any questions, please contact:▷Your service center.▷www.homelink.com on the Internet.
HomeLink is a registered trademark of John‐
son Controls, Inc.
Controls on the interior rearview
mirror
▷LED, arrow 1.▷Buttons, arrow 2.▷The hand-held transmitter, arrow 3, is re‐
quired for programming.
Programming
General information
1.Switch on the ignition.2.Initial setup:
Press and hold the left and right button on
the interior rearview mirror simultaneously
for approximately 20 seconds until the LED
on the interior rearview mirror flashes. ThisSeite 167Interior equipmentControls167
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 172 of 253

erases all programming of the buttons on
the interior rearview mirror.3.Hold the hand-held transmitter for the sys‐
tem to be controlled approx. 1 to 3 in/2.5 to
8 cm away from the buttons on the interior
rearview mirror. The required distance de‐
pends on the manual transmitter.4.Simultaneously press and hold the button
of the desired function on the hand-held
transmitter and the button to be program‐
med on the interior rearview mirror. The
LED on the interior rearview mirror will be‐
gin flashing slowly.5.Release both buttons as soon as the LED
flashes more rapidly. When the LED is
flashing faster, this indicates that the but‐
ton on the interior rearview mirror has been
programmed.
If the LED does not flash faster after at
least 60 seconds, change the distance be‐
tween the interior rearview mirror and the
hand-held transmitter and repeat the step.
Several more attempts at different distan‐
ces may be necessary. Wait at least
15 seconds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the
hand-held transmitter button for 2 sec‐
onds.6.To program other functions on other but‐
tons, repeat steps 3 to 5.
The systems can be controlled using the inte‐
rior rearview mirror buttons.
Special feature of the alternating-
code wireless system
If you are unable to operate the system after
repeated programming, please check if the
system to be controlled features an alternat‐
ing-code system.
Read the system's operating manual, or press
the programmed button on the interior rear‐
view mirror longer. If the LED on the interior
rearview mirror starts flashing rapidly and then
stays lit constantly for 2 seconds, the system
features an alternating-code system. Flashing
and continuous illumination of the LED will re‐
peat for approximately 20 seconds.
For systems with an alternating-code system,
the integrated universal remote control and the
system also have to be synchronized.
Please read the operating manual of the sys‐
tem being set up for information on how to
synchronize the system.
Synchronizing is easier with the aid of a sec‐
ond person.
To synchronize:1.Park the vehicle within range of the re‐
mote-controlled system.2.Program the relevant button on the interior
rearview mirror as described.3.Locate and press the synchronizing button
on the system being programmed. You
have approx. 30 seconds for the next step.4.Hold down the programmed button on the
interior rearview mirror for approximately
3 seconds and then release it. If necessary,
repeat this work step up to three times in
order to finish synchronization. Once syn‐
chronization is complete, the programmed
function will be carried out.
Reprogramming individual buttons
1.Switch on the ignition.2.Press and hold the interior rearview mirror
button to be programmed.3.As soon as the interior rearview mirror LED
starts flashing slowly, hold the hand-held
transmitter for the system to be controlled
approx. 1 to 3 in/2.5 to 8 cm away from the
buttons on the interior rearview mirror. The
required distance depends on the manual
transmitter.Seite 168ControlsInterior equipment168
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 173 of 253

4.Likewise, press and hold the button of the
desired function on the hand-held trans‐
mitter.5.Release both buttons as soon as the inte‐
rior rearview mirror LED flashes more rap‐
idly. When the LED is flashing faster, this
indicates that the button on the interior
rearview mirror has been programmed.
The system can then be controlled by the
button on the interior rearview mirror.
If the LED does not flash faster after at
least 60 seconds, change the distance and
repeat the step. Several more attempts at
different distances may be necessary. Wait
at least 15 seconds between attempts.
Canada: if programming with the hand-
held transmitter was interrupted, hold
down the interior rearview mirror button
and repeatedly press and release the
hand-held transmitter button for 2 sec‐
onds.
Controls
Before operation
Before operating a system using the
integrated universal remote control, ensure
that there are no people, animals, or objects
within the range of movement of the remote- controlled system; otherwise, there is a risk of
injury or damage.
Also follow the safety instructions of the hand-
held transmitter.◀
The system, such as the garage door, can be
operated using the button on the interior rear‐
view mirror while the engine is running or when
the ignition is started. To do this, hold down
the button within receiving range of the system
until the function is activated. The interior rear‐ view mirror LED stays lit while the wireless sig‐
nal is being transmitted.
Deleting stored functions Press and hold the left and right button on the
interior rearview mirror simultaneously for ap‐
proximately 20 seconds until the LED flashes
rapidly. All stored functions are deleted. The
functions cannot be deleted individually.
Ashtray/cigarette lighter Front
Opening
Press on the cover.
Emptying
Place your finger in the depression next to the
ashtray, arrow, and push up at the same time.
The ashtray can be removed.
Lighter Push in the lighter.
The lighter can be removed as
soon as it pops back out.
Seite 169Interior equipmentControls169
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 243 of 253

Band-aids, refer to First aidkit 222
Bar for tow-starting/ towing 224
Basic position, rear seats 56
Battery replacement, vehicle battery 219
Battery replacement, vehicle remote control 34
Battery, vehicle 219
Belts, safety belts 58
Beverage holder, cu‐ pholder 175
Blinds, sun protection 49
BMW ActiveHybrid 30
BMW Assist, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
BMW Homepage 6
BMW Internet page 6
BMW maintenance sys‐ tem 212
Bonus range, ECO PRO 190
Bottle holder, refer to Cu‐ pholder 175
Brake assistant 130
Brake assistant, adaptive 130
Brake discs, breaking in 180
Brake force display 127
Brake lamps, brake force dis‐ play 127
Brake lamps, bulb replace‐ ment 217
Brake lights, adaptive 127
Brake pads, breaking in 180
Braking, hints 183
Breakdown assis‐ tance 221, 222
Breaking in 180
Brightness of Control Dis‐ play 96
Bulb replacement, rear 217
Bulb replacement, see lamp and bulb replacement 214
Button, RES 139 Button, Start/Stop 70
Bypassing, refer to Jump- starting 222
C
California Proposition 65 Warning 8
Calling up mirror adjust‐ ment 46
Calling up seat adjust‐ ment 46
Calling up steering wheel ad‐ justment 46
Camera, backup camera 147
Camera, care 230
Camera, Side View 150
Camera, Top View 151
Can holder, refer to Cu‐ pholder 175
Car battery 219
Car care products 228
Care, displays 230
Care, vehicle 228
Cargo 185
Cargo area lid 40
Cargo area, storage compart‐ ments 175
Cargo, securing 186
Cargo straps, securing cargo 186
Car key, refer to Remote con‐ trol 34
Carpet, care 230
Car wash 227
Catalytic converter, refer to Hot exhaust system 182
CBS Condition Based Serv‐ ice 212
CD/Multimedia, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
Center armrest 174
Center console 16 Center-Lock, see button for
central locking 37
Central locking system 37
Central screen, refer to Con‐ trol Display 18
Changes, technical, refer to Safety 7
Changing parts 214
Changing wheels 218
Changing wheels/tires 203
CHARGE, energy recov‐ ery 74
Charge indicator, high-volt‐ age battery 97
Check Control 86
Checking the oil level elec‐ tronically 208
Children, seating position 66
Children, transporting safely 66
Child restraint fixing sys‐ tem 66
Child restraint fixing system LATCH 67
Child restraint fixing systems, mounting 66
Child safety locks 69
Child seat, mounting 66
Child seats 66
Chrome parts, care 229
Cigarette lighter 169
Cleaning, displays 230
Climate control 159
Climate control laminated tinted safety glass 182
Climate control wind‐ shield 182
Clock 89
Closing/opening from in‐ side 40
Closing/opening via door lock 39
Closing/opening with remote control 38
Clothes hooks 175
Coasting 73 Seite 239Everything from A to ZReference239
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 244 of 253

Collision warning with brakingfunction 116
Collision warning with City Braking function 114
Combination switch, refer to Turn signals 78
Combination switch, refer to Wiper system 79
Combustion engine, start‐ ing 72
COMFORT+ program, Driving Dynamics Control 134
Comfort Access 43
COMFORT program, Driving Dynamics Control 134
Computer 93
Condensation on win‐ dows 160
Condensation under the vehi‐ cle 184
Condition Based Service CBS 212
Confirmation signal 45
ConnectedDrive, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
ConnectedDrive Services
Contact with water, hybrid system 226
Control Display 18
Control Display, settings 95
Controller 18
Control systems, driving sta‐ bility 130
Convenient opening 38
Coolant 210
Coolant temperature 89
Cooling function 161
Cooling, maximum 161
Cooling system 210
Corrosion on brake discs 184
Cruise control 142
Cruise control, active with Stop & Go 136
Cruising range 89 Cupholder 175
Curb weight 235
D
Damage, tires 203
Damping Control, dy‐ namic 132
Data, technical 234
Date 89
Daytime running lights 101
Deactivating drive readi‐ ness 72
Defrosting, refer to Windows, defrosting 160
Destination distance 94
Digital clock 89
Dimensions 234
Dimmable exterior mirrors 63
Dimmable interior rearview mirror 64
Direction indicator, refer to Turn signals 78
Display in windshield 157
Display lighting, refer to In‐ strument lighting 103
Displays 85
Displays, cleaning 230
Displays, hybrid system 96
Disposal, coolant 211
Disposal, vehicle battery 220
Distance control, refer to PDC 144
Distance to destination 94
Divided screen view, split screen 22
Door lock, refer to Remote control 34
Doors, Automatic Soft Clos‐ ing 40
DRIVE, Driving with combus‐ tion engine 74
Drive-off assistant 130
Drive-off assistant, refer to DSC 130 Driver assistance, see Intelli‐
gent Safety 113
Drive readiness in detail 71
Drive readiness states 70
Driving Assistant, see Intelli‐ gent Safety 113
Driving Dynamics Con‐ trol 132
Driving instructions, breaking in 180
Driving instructions, hybrid system 180
Driving mode 132
Driving notes, general 182
Driving stability control sys‐ tems 130
Driving tips 182
Driving with combustion en‐ gine, DRIVE 74
DSC Dynamic Stability Con‐ trol 130
DTC driving dynamics 131
DTC Dynamic Traction Con‐ trol 131
Dynamic Damping Con‐ trol 132
Dynamic Stability Control DSC 130
Dynamic Traction Control DTC 131
E
eBOOST, assistance for the combustion engine 74
ECO PRO 189
ECO PRO, bonus range 190
ECO PRO display 189
ECO PRO driving mode 189
ECO PRO mode 189
ECO PRO Tip - driving in‐ struction 190
eDRIVE, electric driving 73
Electric drive readiness, Si‐ lent Start 71
Electric driving, eDRIVE 73 Seite 240ReferenceEverything from A to Z240
Online Edition for Part no. 01 40 2 909 774 - VI/13
Page 246 of 253

Hand-held transmitter, alter‐nating code 168
Hazard warning flashers 221
Head airbags 105
Headlamp control, auto‐ matic 101
Headlamp courtesy delay fea‐ ture 100
Headlamp flasher 79
Headlamp glass 215
Headlamps, care 228
Headlamp washer system 79
Headliner 17
Head restraints 52
Head restraints, front 59
Head restraints, rear 60
Head-Up Display 157
Head-up Display, care 230
Heavy cargo, stowing 186
Height with roof-mounted aerial, vehicle 234
High-beam Assistant 102
High beams 79
High beams/low beams, refer to High-beam Assistant 102
High-voltage battery, charge indicator 97
High voltage battery, dis‐ charge 181
Hills 183
Hill start assistant, refer to Drive-off assistant 130
Hints 6
Holder for beverages 175
Homepage 6
Hood 206
Horn 14
Hotel function, trunk lid 43
Hot exhaust system 182
HUD Head-Up Display 157
Hybrid system, adapting to the course of the road 99
Hybrid system, at a glance 30
Hybrid system, automatic de‐ activation 226 Hybrid system, contact with
water 226
Hybrid system, displays 96
Hybrid system, safety 225
Hydroplaning 183
I Ice warning, refer to External temperature warning 89
Icy roads, refer to External temperature warning 89
Identification marks, tires 201
Identification number, refer to Important features in the en‐
gine compartment 206
iDrive 18
Ignition key, refer to Remote control 34
Ignition off 70
Ignition on 70
Indication of a flat tire 109 , 111
Indicator and warning lamps 86
Individual air distribution 160
Individual settings, refer to Personal Profile 35
Inflation pressure, tires 199
Inflation pressure warning FTM, tires 108
Info display, refer to Com‐ puter 93
Initialize, Tire Pressure Moni‐ tor TPM 111
Initializing, Flat Tire Monitor FTM 108
Instrument cluster 85
Instrument cluster, electronic displays 86
Instrument lighting 103
Integrated key 34
Integrated universal remote control 167
Intelligent Emergency Re‐ quest 221 Intelligent Safety 113
Intensity, AUTO pro‐ gram 160
Interior equipment 167
Interior lamps 104
Interior lamps via remote con‐ trol 38
Interior motion sensor 47
Interior rearview mirror 63
Interior rearview mirror, auto‐ matic dimming feature 64
Internet page 6
Interval display, service re‐ quirements 90
J Jacking points for the vehicle jack 218
Joystick, automatic transmis‐ sion 82
Jump-starting 222
K
Key/remote control 34
Keyless Go, refer to Comfort Access 43
Key Memory, refer to Per‐ sonal Profile 35
Kickdown, automatic trans‐ mission 82
Knee airbag 105
L Lamp replacement, rear 217
Lamps 100
Lamps and bulbs 214
Lane departure warning 124
Lane margin, warning 124
Language on Control Dis‐ play 96
Lashing eyes, securing cargo 186 Seite 242ReferenceEverything from A to Z242
Online Edition for Part no. 01 40 2 909 774 - VI/13