tow BMW M6 COUPE 2013 F13 Owner's Guide
[x] Cancel search | Manufacturer: BMW, Model Year: 2013, Model line: M6 COUPE, Model: BMW M6 COUPE 2013 F13Pages: 214, PDF Size: 7.08 MB
Page 168 of 214

test surfaces of asphalt and concrete. A tire
marked C may have poor traction performance.
The traction grade assigned to this tire is
based on straight-ahead braking traction tests,
and does not include acceleration, cornering,
hydroplaning, or peak traction characteristics.
Temperature
The temperature grades are A, the highest, B,
and C, representing the tire's resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the ma‐
terial of the tire to degenerate and reduce tire
life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds
to a level of performance which all passenger
car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades Band
A represent higher levels of performance on
the laboratory test wheel than the minimum re‐
quired by law.
Temperature grade for this tire
The temperature grade for this tire is es‐
tablished for a tire that is properly inflated and
not overloaded. Excessive speed, underinfla‐
tion, or excessive loading, either separately or
in combination, can cause heat buildup and
possible tire failure.
If necessary, have the vehicle towed.◀
M+S
Winter and all-season tires with better cold
weather performance than summer tires.
Tire tread Summer tires
Do not drive with a tire tread depth of less than
0.12 in/3 mm.
There is an increased danger of hydroplaning if
the tread depth is less than 0.12 in/3 mm.Winter tires
Do not drive with a tire tread depth of less than
0.16 in/4 mm.
Below a tread depth of 0.16 in/4 mm, tires are
less suitable for winter operation.
Minimum tread depth
Wear indicators are distributed around the
tire's circumference and have the legally re‐
quired minimum height of 0.063 in/1.6 mm.
They are marked on the side of the tire with
TWI, Tread Wear Indicator.
Tire damage
General information
Inspect your tires often for damage, foreign
objects lodged in the tread, and tread wear.
Notes
Driving over rough or damaged road surfaces,
as well as debris, curbs and other obstacles can cause serious damage to wheels, tires and
suspension parts. This is more likely to occur
with low-profile tires, which provide less cush‐
ioning between the wheel and the road. Be
careful to avoid road hazards and reduce your
speed, especially if your vehicle is equipped
with low-profile tires.
Indications of tire damage or other vehicle de‐
fects:
▷Unusual vibrations during driving.Seite 164MobilityWheels and tires164
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 169 of 214

▷Unusual handling such as a strong ten‐
dency to pull to the left or right.
Damage can, e. g., be caused by driving over
curbs, road damage, or similar things.
In case of tire damage
If there are indications of tire damage, re‐
duce your speed immediately and have the
wheels and tires checked right away; other‐
wise, there is the increased risk of an accident.
Drive carefully to the nearest service center. If
necessary, have the vehicle towed.
Otherwise, tire damage can be life-threatening
for vehicle occupants and other traffic partici‐
pants.◀
Repair of tire damage
For safety reasons, the manufacturer of
your vehicle recommends that you do not have
damaged tires repaired; they should be re‐
placed. Otherwise, damage can occur as a re‐
sult.◀
Changing wheels and tires
Mounting Information on mounting tires
Have mounting and balancing performed
only by a service center.
If this work is not carried out properly, there is
the danger of subsequent damage and related
safety hazards.◀
Wheel and tire combination
Information on the correct wheel-tire combina‐
tion and rim versions for your vehicle can be
obtained from your service center.
Incorrect wheel and tire combinations impair
the function of a variety of systems such as
ABS or DSC.
To maintain good handling and vehicle re‐
sponse, use only tires with a single tread con‐
figuration from a single manufacturer.
Following tire damage, have the original wheel
and tire combination remounted on the vehicle
as soon as possible.
Approved wheels and tires
The manufacturer of your vehicle recom‐
mends that you use only wheels and tires that
have been approved for your particular vehicle
model.
For example, despite having the same official
size ratings, variations can lead to body con‐
tact and with it, the risk of severe accidents.
The manufacturer of your vehicle cannot eval‐
uate non-approved wheels and tires to deter‐
mine if they are suited for use, and therefore
cannot ensure the operating safety of the vehi‐
cle if they are mounted.◀
Recommended tire brands
For each tire size, the manufacturer of your ve‐
hicle recommends certain tire brands. These
can be identified by a star on the tire sidewall.
With proper use, these tires meet the highest
standards for safety and handling.
New tires Due to technical factors associated with their
manufacture, tires do not achieve their full
traction potential until after an initial breaking-
in period.
Seite 165Wheels and tiresMobility165
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 173 of 214

Stowing the Mobility System1.Unscrew the filling hose of the sealant bot‐
tle from the wheel.2.Unscrew the compressor connection hose
from the sealant bottle.3.Connect the sealant bottle filling hose that
was previously connected to the valve to
the vacant connector on the sealant bottle.
This prevents left-over sealant from escap‐
ing from the bottle.4.Wrap the empty sealant bottle in suitable
material to avoid dirtying the cargo area.5.Stow the Mobility System back in the vehi‐
cle.
Distributing the sealant
Immediately drive approx. to ensure that the
sealant is evenly distributed in the tire.
Do not exceed a speed of .
Do not drop below if possible.
Correcting the tire inflation pressure
1.Stop at a suitable location.2.Screw the connection hose of the com‐
pressor directly onto the tire valve.3.Insert the connector into the power socket
in the vehicle interior.4.Correct the tire inflation pressure to
2.5 bar.▷Increase pressure: with the ignition
turned on or the engine running, switch
on the compressor.▷To reduce the pressure: press the but‐
ton on the compressor.
Continuing the trip
Do not exceed the maximum permissible
speed of 50 mph/80 km/h.
Reinitialize the Flat Tire Monitor, refer to
page 98.
Reinitialize the Tire Pressure Monitor, refer to
page 96.
Replace the defective tire and the sealant bot‐
tle of the Mobility System as soon as possible.
Snow chains
Fine-link snow chains
Only certain types of fine-link snow chains
have been tested by the manufacturer of your
vehicle, classified as road-safe and recom‐
mended.
Consult your service center for more informa‐
tion.
Use Use only in pairs on the rear wheels, equipped
with the tires of the following size:
255/40 R 19
Follow the chain manufacturer's instructions.
Make sure that the snow chains are always
sufficiently tight. Retighten as needed accord‐
ing to the chain manufacturer's instructions.
Do not initialize the Flat Tire Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
Do not initialize the Tire Pressure Monitor after
mounting snow chains, as doing so may result
in incorrect readings.
When driving with snow chains, if necessary
briefly activate M Dynamic Mode.
Maximum speed with snow chains Do not exceed a speed of 30 mph/50 km/h
when using snow chains.Seite 169Wheels and tiresMobility169
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 182 of 214

Replacing componentsVehicle equipmentAll standard, country-specific and optional
equipment that is offered in the model series is
described in this chapter. Therefore, equip‐
ment is also described that is not available in a
vehicle, e. g., because of the selected optional
equipment or country variant. This also applies
for safety-related functions and systems.
Onboard vehicle tool kit
The onboard vehicle tool kit is stored under
the cargo floor cover in the cargo area.
Wiper blade replacement
General information Do not fold down the wipers without
wiper blades
Do not fold down the wipers if wiper blades
have not been installed; this may damage the
windshield.◀
Replacing the wiper blades1.To change the wiper blades, fold up, refer
to page 72, the wiper arms.2.Fold up the wipers.3.Position the wiper blade in a horizontal po‐
sition.4.Remove the wiper blade toward one side.5.Insert the new wiper blade in reverse order
of removal until it locks in place.6.Fold down the wipers.
Lamp and bulb replacement
Hints
Lamps and bulbs
Lamps and bulbs make an essential contribu‐
tion to vehicle safety.
The manufacturer of the vehicle recommends
that you entrust corresponding procedures to
Seite 178MobilityReplacing components178
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 191 of 214

corresponding engine or body ground of
the vehicle to be started.
Starting the engine
Never use spray fluids to start the engine.
1.Start the engine of the assisting vehicle
and let it run for several minutes at an in‐
creased idle speed.2.Start the engine of the vehicle being
started in the usual way.
If the first starting attempt is not success‐
ful, wait a few minutes before making an‐
other attempt in order to allow the dis‐
charged battery to recharge.3.Let both engines run for several minutes.4.Disconnect the jumper cables in the re‐
verse order.
Check the battery and recharge if necessary.
Tow-starting and towing Manual transmission
Observe before towing your vehicle
Gearshift lever in neutral position.
Towing When the parking brake is blocked
The parking brake cannot be released
manually.
Do not tow the vehicle with the parking brake
blocked, or the vehicle can be damaged.
Contact your service center.◀
Follow the towing instructions
Follow all towing instructions; otherwise,
vehicle damage or accidents may occur.◀
▷Make sure that the ignition is switched on;
otherwise, the low beams, tail lamps, turn
signals, and windshield wipers may be un‐
available.▷Do not tow the vehicle with the rear axle
tilted, as the front wheels could turn.▷When the engine is stopped, there is no
power assist. Consequently, more force
needs to be applied when braking and
steering.▷Larger steering wheel movements are re‐
quired.▷The towing vehicle must not be lighter
than the vehicle being towed; otherwise,
it will not be possible to control the vehicle
response.
Tow truck
Have your vehicle transported with a tow truck
with a so-called lift bar or on a flat bed.
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
Automatic transmission: transporting
your vehicle
Note Your vehicle is not permitted to be towed.
Therefore, contact a service center in the
event of a breakdown.
Do not have the vehicle towed
Have your vehicle transported on a load‐
ing platform only; otherwise, damage may oc‐
cur.◀
Seite 187Breakdown assistanceMobility187
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 192 of 214

Tow truck
Do not lift the vehicle
Do not lift the vehicle by the tow fitting or
body and chassis parts; otherwise, damage
may result.◀
Use the tow fitting screwed in at the front for
maneuvering the vehicle only.
Towing other vehicles
General information Light towing vehicle
The towing vehicle must not be lighter
than the vehicle being towed; otherwise, it will
not be possible to control the vehicle re‐
sponse.◀
Attaching the tow bar/tow rope correctly
Attach the tow bar or tow rope to the tow
fitting; connecting it to other vehicle parts may
cause damage.◀
▷Switch on the hazard warning system, de‐
pending on local regulations.▷If the electrical system has failed, clearly
identify the vehicle being towed by placing
a sign or a warning triangle in the rear win‐
dow.
Tow bar
The tow fittings used should be on the same
side on both vehicles.
Should it prove impossible to avoid mounting
the tow bar at an offset angle, please observe
the following:▷Maneuvering capability is limited during
cornering.▷The tow bar will generate lateral forces if it
is secured with an offset.
Tow rope
When starting to tow the vehicle, make sure
that the tow rope is taut.
To avoid jerking and the associated stresses
on the vehicle components when towing, al‐
ways use nylon ropes or nylon straps.
Attaching the tow rope correctly
Only secure the tow rope on the tow fit‐
ting; otherwise, damage can occur when it is
secured on other parts of the vehicle.◀
Tow fitting
The screw-in tow fitting should always be car‐
ried in the vehicle. It can be screwed in at the
front or rear of the BMW. It is contained in the
onboard vehicle tool kit under the cargo floor
cover.
Tow fitting, information on use
▷Use only the tow fitting provided with
the vehicle and screw it all the way in.▷Use the tow fitting for towing on paved
roads only.Seite 188MobilityBreakdown assistance188
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 193 of 214

▷Avoid lateral loading of the tow fitting, e.g.,
do not lift the vehicle by the tow fitting.
Otherwise, damage to the tow fitting and the
vehicle can occur.◀
Screw thread
Push out the cover by pressing on the top
edge.
Tow-starting
Double-clutch transmission Do not tow-start the vehicle.
Due to the double-clutch transmission, the en‐
gine cannot be started by tow-starting.
Have the cause of the starting difficulties rem‐
edied.
Manual transmission
If possible, do not tow-start the vehicle but
start the engine by jump-starting, refer to
page 186. If the vehicle is equipped with a cat‐
alytic converter, only tow-start while the en‐
gine is cold.
1.Switch on the hazard warning system and
comply with local regulations.2.Ignition, refer to page 59, on.3.Engage third gear.4.Have the vehicle tow-started with the
clutch pressed and slowly release the
clutch. After the engine starts, immediately
press on the clutch again.5.Stop at a suitable location, remove the tow
bar or rope, and switch off the hazard
warning system.6.Have the vehicle checked.Seite 189Breakdown assistanceMobility189
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 204 of 214

Everything from A to Z
IndexA ABS, Antilock Brake Sys‐ tem 113
Acceleration Assistant, refer to Launch Control 68
Activated-charcoal filter 133
Active Blind Spot Detec‐ tion 109
Active M differential 115
Active Protection 110
Active seat, front 47
Active seat ventilation, front 47
Adaptive brake lights, refer to Brake force display 110
Adaptive light control 89
Additives, oil 173
Adjusting, steering wheel 53
Adjustments, seats/head re‐ straints 45
After washing vehicle 191
Airbags 93
Airbags, indicator/warning light 94
Air circulation, refer to Recir‐ culated-air mode 132
Air distribution, manual 131
Air drying, refer to Cooling function 132
Air flow, automatic climate control 131
Air pressure, tires 161
Air vents, refer to Ventila‐ tion 133
Alarm system 40
Alarm, unintentional 41
All around the center con‐ sole 14
All around the interior rear‐ view mirror 15 All around the steering
wheel 12
All-season tires, refer to Win‐ ter tires 166
Alternating-code hand-held transmitter 136
Alternative oil types 173
Ambient light 91
Antifreeze, washer fluid 73
Antilock Brake System, ABS 113
Anti-slip control, refer to DSC 113
Approved engine oils 173
Armrest, refer to Front center armrest 141
Arrival time 85
Ashtray 137
Assistance, Roadside Assis‐ tance 185
Assistance when driving off 113
Attentiveness assistant 111
AUTO intensity 131
Automatic car wash 190
Automatic Curb Monitor 52
Automatic deactivation, front passenger airbags 95
Automatic headlamp con‐ trol 89
Automatic locking 39
Automatic recirculated-air control 132
Automatic Soft Closing, doors 36
AUTO program, automatic cli‐ mate control 131
AUTO program, intensity 131
Auto Start/Stop function 61
Average fuel consumption 84
Average speed 84 Axle loads, weights 197
B Backrest curvature, refer to Lumbar support 46
Backrest, seats 45
Backrest, width 46
Backup camera 121
Band-aids, refer to First aid kit 185
Bar for tow-starting/ towing 188
Battery replacement, vehicle battery 182
Battery replacement, vehicle remote control 30
Battery, vehicle 182
Belts, safety belts 48
Beverage holder, cu‐ pholder 142
Blinds, sun protection 42
BMW Assist, see user's manual for Navigation, En‐
tertainment and Communi‐
cation
BMW Homepage 6
BMW Internet page 6
BMW maintenance sys‐ tem 176
BMW M technology 146
Bottle holder, refer to Cu‐ pholder 142
Brake assistant 113
Brake discs, breaking in 148
Brake force display 110
Brake lamps, brake force dis‐ play 110
Brake lamps, bulb replace‐ ment 180
Brake lights, adaptive 110 Seite 200ReferenceEverything from A to Z200
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 207 of 214

External temperature warn‐ing 78
Eyes for securing cargo 153
F
Failure message, refer to Check Control 75
False alarm, refer to Uninten‐ tional alarm 41
Fan, refer to Air flow 131
Fault displays, refer to Check Control 75
Filler neck for engine oil 173
Fine wood, care 192
First aid kit 185
Fitting for towing, refer to Tow fitting 188
Flat tire, changing wheels 181
Flat Tire Monitor FTM 98
Flat tire, repairing 166
Flat tire, Tire Pressure Moni‐ tor TPM 96
Flat tire, warning lamp 97, 99
Flooding 150
Floor carpet, care 193
Floor mats, care 193
Fold-out position, windshield wipers 72
Foot brake 150
For the headliner, refer to All around the interior rearview
mirror 15
Front airbags 93
Front center armrest 141
Front lamps 178
Front passenger airbags, au‐ tomatic deactivation 95
Front passenger airbags, indi‐ cator lamp 95
Front seats 45
Front turn signals, refer to Light-emitting diodes,
LEDs 179
FTM Flat Tire Monitor 98 Fuel 160
Fuel cap 158
Fuel consumption, current 79
Fuel consumption, refer to Average fuel consump‐
tion 84
Fuel filler flap 158
Fuel gauge 77
Fuel quality 160
Fuel recommendation 160
Fuel, tank capacity 198
Fuse 182
G
Garage door opener, refer to Integrated universal remote
control 135
Gasoline 160
Gasoline quality 160
Gear change 66
Gear shift indicator 81
General driving notes 149
Glass sunroof, powered with tilt function 42
Glove compartment 140
Gross vehicle weight, ap‐ proved 197
Gross weight, permissible for trailer towing 197
Ground clearance 151
H
Handbrake, refer to Parking brake 63
Hand-held transmitter, alter‐ nating code 136
Hazard warning flashers 184
Head airbags 93
Headlamp control, auto‐ matic 89
Headlamp courtesy delay fea‐ ture 88
Headlamp courtesy delay fea‐ ture via remote control 34 Headlamp flasher 71
Headlamp glass 179
Headlamps 178
Headlamps, care 191
Headlamp washer system 71
Head restraints 45
Head restraints, front 49
Head-Up Display 127
Head-up Display, care 193
Head-up display, M view 128
Head-up display, standard view 128
Heavy cargo, stowing 153
Height, seats 45
Height, vehicle 196
High-beam Assistant 90
High beams 71
High beams/low beams, refer to High-beam Assistant 90
Higher speed range 151
Hills 150
Hill Start Assistant 115
Hill start assistant, refer to Drive-off assistant 113
Hints 6
Holder for beverages 142
Homepage 6
Hood 170
Horn 12
Hotel function, trunk lid 37
Hot exhaust system 149
HUD Head-Up Display 127
Hydroplaning 149
I Ice warning, refer to External temperature warning 78
Icy roads, refer to External temperature warning 78
Identification marks, tires 163
Identification number, refer to Important features in the en‐
gine compartment 170
iDrive 16 Seite 203Everything from A to ZReference203
Online Edition for Part no. 01 40 2 910 796 - VI/13
Page 209 of 214

Manual operation, fuel fillerflap 158
Manual operation, Park Dis‐ tance Control PDC 120
Manual operation, Side View 127
Manual operation, Top View 125
Marking on approved tires 165
Massage seat, front 47
Master key, refer to Remote control 30
Maximum cooling 132
Maximum speed, display 82
Maximum speed, winter tires 166
M carbon ceramic brake 146
M Compound brake 146
M differential, active 115
MDM, M Dynamic Mode 114
M double-clutch transmis‐ sion 65
M Drive 53
M Driver's Package, driving instructions 151
M Driving Dynamics Con‐ trol 69
M Dynamic Mode MDM 114
Measure, units of 86
Medical kit 185
Memory for seat, mirrors, steering wheel 50
Menu in instrument clus‐ ter 83
Menus, operating, iDrive 16
Menus, refer to iDrive operat‐ ing concept 17
Messages, refer to Check Control 75
Microfilter 133
Minimum tread, tires 164
Mirror 51
Mirror memory 50
Mobile communication devi‐ ces in the vehicle 149 Mobility System 166
Modifications, technical, refer to Safety 7
Moisture in headlamp 179
Monitor, refer to Control Dis‐ play 16
Mounting of child restraint fix‐ ing systems 55
M technology 146
Multifunction steering wheel, buttons 12
M view, head-up display 128
N
Navigation, see user's manual for Navigation, Entertain‐
ment and Communication
Neck restraints, front, refer to Head restraints 49
Neutral cleaner, see wheel cleaner 192
New wheels and tires 165
Night Vision with pedestrian detection 104
No Passing Information 82
Nylon rope for tow-starting/ towing 188
O OBD Onboard Diagnosis 177
OBD, see OBD Onboard Di‐ agnosis 177
Obstacle marking, rearview camera 123
Octane rating, refer to Gaso‐ line quality 160
Odometer 78
Office, see user's manual for Navigation, Entertainment
and Communication
Oil 172
Oil, adding 173
Oil additives 173
Oil change 174 Oil change interval, service
requirements 80
Oil filler neck 173
Oil types, alternative 173
Oil types, approved 173
Old batteries, disposal 182
Onboard monitor, refer to Control Display 16
Onboard vehicle tool kit 178
Opening and closing 30
Opening and closing, from in‐ side 36
Opening and closing via door lock 35
Opening and closing, with re‐ mote control 34
Operating concept, iDrive 16
Optional equipment, standard equipment 6
Outside air, refer to Auto‐ matic recirculated-air con‐
trol 132
Overheating of engine, refer to Coolant temperature 78
Overtaking prohibitions 82
P Paint, vehicle 191
Park Distance Control PDC 119
Parked-car ventilation 133
Parked vehicle, condensa‐ tion 151
Parking aid, refer to PDC 119
Parking brake 63
Parking lamps 88
Parking lamps and roadside parking lamps, refer to
Light-emitting diodes,
LEDs 179
Passenger side mirror, tilting downward 52
Pathway lines, rearview cam‐ era 123 Seite 205Everything from A to ZReference205
Online Edition for Part no. 01 40 2 910 796 - VI/13