brake light BMW MOTORRAD K 1200 GT 2007 Rider's Manual (in English)

Insert bulb3into the bulb
socket.
Turn the bulb socket clockwise
to install.
Parking light, left: connect
plug 2. Parking light, right: connect
plug
1.
Replacing brake-light,
rear light and rear-
indicator bulbs
If it is not standing firmly,
the motorcycle could topple
in the course of the operations
described below.
Always make sure that the
motorcycle is stable and firmly
supported.
Make sure the ground is level
and firm and place the motor-
cycle on its stand. Switch off the ignition.
Remove screws
1.
Pull the bulb housing to the
rear until it is clear of the hold-
ers.
8127zMaintenance

Turn bulb socket2(brake-light
/rear-light bulb) or 3(indicat-
or bulb) counter-clockwise to
remove from the bulb housing. Press bulb
4into socket 5and
remove by turning it counter-
clockwise.
Replace the defective bulb.
Bulb for tail light/brake
light
P21W / 12 V / 21 W Bulbs for flashing turn
indicators, rear
P21W / 12 V / 21 W
Use a clean, dry cloth to hold
the new bulb. Press bulb
4into socket 5and
turn it clockwise to install.
Turn bulb socket 2(indicator
bulb) or 3(brake-light /rear-light
bulb) clockwise to install it in
the bulb housing.
8128zMaintenance

Care productsBMW Motorrad recommends
that you use the cleaning and
care products you can obtain
from your authorised BMW Mo-
torrad dealer. The substances in
BMW Care Products have been
tested in laboratories and in prac-
tice; they provide optimised care
and protection for the materials
used in your vehicle.The use of unsuitable
cleaning and care products
can damage vehicle components.
Do not use solvents such as cel-
lulose thinners, cold cleaners,
fuel or the like, and do not use
cleaning products that contain
alcohol.Washing motorcycleBMW Motorrad recommends
that you use BMW insect re-
mover to soften and wash off
insects and stubborn dirt on painted parts prior to washing
the motorcycle.
To prevent stains, do not wash
the motorcycle immediately after
it has been exposed to strong
sunlight and do not wash it in the
sun.
Make sure that the motorcycle
is washed frequently, especially
during the winter months.
To remove road salt, clean the
motorcycle with cold water im-
mediately after every trip.
After the motorcycle has
been washed, ridden
through water or ridden in
the rain, the brake discs and
pads might be wet and the
brakes might not take effect
immediately.
Apply the brakes in good time
until the brakes have dried out.
Warm water intensifies the
effect of salt. Use only cold water to wash off
road salt.
The high pressure of steam
cleaners can damage seals,
the hydraulic brake system, the
electrical system, and the seat.
Do not use a steam jet or high-
pressure cleaning equipment.
Cleaning easily
damaged componentsPlasticsClean plastic parts with water
and BMW plastic care emulsion.
This includes in particular:
Windscreen and slipstream de-
flectors
Headlight lens made of plastic
Glass cover of the instrument
cluster
Black, unpainted parts
If plastic parts are cleaned
using unsuitable cleaning
9138zCare

Battery
Battery, manufacturer and designationGEL 19
Battery type Gel battery
Battery rated voltage 12 V
Battery rated capacity 19 Ah
Technical data
Spark plugs, manufacturer and designation NGK KR9CI
Electrode gap of spark plug 0.8 mm
Lighting
Bulb for high-beam headlight H7 / 12 V / 55 W
Bulb for low-beam headlight H7 / 12 V / 55 W
with OE Xenon lights: D2R / 35 W
Bulb for parking light W5W / 12 V / 5 W
Bulb for tail light/brake light P21W / 12 V / 21 W
Bulbs for flashing turn indicators, front H21W / 12 V / 21 W
Bulbs for flashing turn indicators, rear P21W / 12 V / 21 W
10151zTechnical data

A
Abbreviations and symbols, 6
ABSSelf-diagnosis, 82
Warnings, 32
Accessories General instructions, 97
Anti-theft alarm, 18 Warnings, 41
ASC Self-diagnosis, 82
Switching off, 61
Switching on, 61, 62
Warnings, 34
B
Battery Battery compartment, 11
Charging battery when
connected, 132
Charging battery when
disconnected, 133
Installation, 135
Technical data, 151 Warning, battery charge
current, 28
Beam throw, 13
Brake fluid Checking level, front, 13
Checking level, rear, 15
Test, 111
Brake pads Running in, 83
Test, 109
Brakes Adjust the handbrake lever, 67
Technical data, 149
Bulbs General instructions, 123
Replacing brake-light bulb, 127
Replacing front turn indicator
bulbs, 129
Replacing high-beam headlight
bulb, 123
Replacing low-beam headlight
bulb, 123
Replacing parking-light
bulbs, 126
Replacing rear light bulb, 127 Replacing rear-indicator
bulbs, 127
Technical data, 151
Warning, bulb failure, 29, 30
C
Care, 137
Case Closing, 100
Installing, 101
Opening, 100
Removing, 101
Checklist, 80
Clock Adjusting, 18, 49
Clutch Adjusting clutch lever, 66
Technical data, 147
Confirmation of maintenance work, 158
Coolant Temperature gauge, 22
12165zIndex

Seat, 15Adjust the seat height, 62
Seat heating, 60
Seat lock, 11
Seats Install the front seat, 75
Install the rear seat, 75
Remove the front seat, 74
Remove the rear seat, 73
Service, 156 Status indicators on the
display, 22
Service Card, 156
Side stand For starting, 80
Spark plugs, 151
Speedometer, 18
Spring preload Adjusting for rear wheel, 68
Spring preload, rear Adjusting, 11
Starter, 17
Starting, 80 Steering lock
Locking, 48
Stowage compartment, 13, 66
Suspension damping, rear Adjusting, 11
T
Technical data Battery, 151
Brakes, 149
Bulbs, 151
Clutch, 147
Dimensions, 152
Electrics, 150
Engine, 145
Engine oil, 146
Frame, 152
Fuel, 146
Rear-wheel drive, 148
Running gear, 148
Spark plugs, 151
Standards, 7
Transmission, 147
Weights, 153 Wheels and tyres, 149
Telltale lights, 18
Toolkit, 15 Service kit, 106
Standard kit, 106
Topcase Closing, 102
Installing, 103
Opening, 102
Removing, 103
Torques, 141
Transmission For starting, 80
Technical data, 147
Troubleshooting chart, 142
Turn indicators Left, 16
Right, 17
Switching off, 17, 57
Switching on left, 56
Switching on right, 57
12168zIndex