headlight bulb BMW MOTORRAD K 1200 R 2007 Rider's Manual (in English)

If the battery is not char-
ging, continuing to ride can
cause it to discharge completely,
in which case it will suffer irrepar-
able damage.
If possible, do not continue your
journey.
Battery is not being charged.
You can continue to ride until
the battery is discharged. Bear
in mind, however, that the en-
gine could cut out suddenly
and that the battery could dis-
charge until completely flat,
in which case it might have
suffered irreparable damage.
Have the fault rectified as
quickly as possible by a
specialist workshop, preferably
an authorised BMW Motorrad
dealer.
Rear light bulb defective General warning light shows
yellow.
LAMPR !
appears on the dis-
play.
A defective bulb places
your safety at risk because
it is easier for other users to
oversee the motorcycle.
Replace defective bulbs as
soon as possible; always carry a
complete set of spare bulbs if
possible.
Rear light or brake light bulb de-
fective.
Replacing brake light and rear
light bulb ( 122)
Front light bulb defective
LAMPF !
appears on the dis-
play.
A defective bulb places
your safety at risk because
it is easier for other users to
oversee the motorcycle.
Replace defective bulbs as
soon as possible; always carry a complete set of spare bulbs if
possible.
Low-beam headlight, high-beam
headlight, side-light or turn-indic-
ator bulb defective.
Replacing low-beam and high-
beam headlight bulb ( 118)
Replacing parking-light bulb
( 120)
Replacing turn indicator bulbs,
front and rear ( 124)
Bulbs defective General warning light shows
yellow.
LAMPS !
appears on the dis-
play.
A defective bulb places
your safety at risk because
it is easier for other users to
oversee the motorcycle.
Replace defective bulbs as
soon as possible; always carry a
complete set of spare bulbs if
possible.
328zStatus indicators

Press the lever down to the
ground.BulbsGeneral instructionsThe failure of a bulb is signalled
in the display by the defective
lamp symbol. If the brake or rear
light fails, the symbol is accom-
panied by the 'General' warning
light, which lights up yellow. If
the rear light fails the second fil-
ament of the brake light shines
at reduced brightness to double
as a rear light. Even though you
have this substitute rear light, theindicators in the display tell you
that a bulb defect has occurred.
A defective bulb places
your safety at risk because
it is easier for other users to
oversee the motorcycle.
Replace defective bulbs as
soon as possible; always carry a
complete set of spare bulbs if
possible.
The bulb is pressurised and
can cause injury if dam-
aged.
Wear protective goggles and
gloves when changing bulbs.
The types of bulb fitted to
your motorcycle are listed
in the section entitled "Technical
data".
Do not touch the glass of
new bulbs with your fingers.
Use a clean, dry cloth to hold
the bulbs when handling them.
Dirt deposits, in particular oil and
grease, interfere with heat radi- ation from the bulb. This leads
to overheating and shortens the
bulb's operating life.
Replacing low-beam and
high-beam headlight bulb
If it is not standing firmly,
the motorcycle could topple
in the course of the operations
described below.
Always make sure that the
motorcycle is stable and firmly
supported.
Make sure the ground is level
and firm and place the motor-
cycle on its stand.
Switch off the ignition. Turn the handlebars to the
left to facilitate access.
8118zMaintenance

Remove cover1(high-beam
headlight) or cover 2(low-beam
headlight) by turning cover
counter-clockwise.
Disconnect plug 3. Disengage spring clip
4from
the latches and swing it up.
The spring clip might face
in a direction other than
that shown here, depending on
the light. Remove bulb
5.
Replace the defective bulb.
Bulb for high-beam
headlight
H7/12V/55W Bulb for low-beam head-
light
H7/12V/55W
8119zMaintenance

Install bulb5. When installing,
make sure that tab 6is point-
ing up.
Engage spring retainer 4in the
catches. Connect plug
3.
Install cover 1(high-beam
headlight) or cover 2(low-beam
headlight) by turning cover
clockwise.
Replacing parking-light
bulb
If it is not standing firmly,
the motorcycle could topple
in the course of the operations
described below.
Always make sure that the
motorcycle is stable and firmly
supported.
Make sure the ground is level
and firm and place the motor-
cycle on its stand.
Switch off the ignition.
8120zMaintenance

Remove securing screws1
from both sides of the bulb
housing.
Pull the bulb housing forward
to remove it and tilt it slightly
down. Remove bulb holder
2from the
headlight housing by turning it
counter-clockwise.
Remove bulb 3from the bulb
holder.
Replace the defective bulb.
Bulb for parking light
W5W / 12 V / 5 W Insert bulb
3into the bulb
socket.
Turn the bulb socket clock-
wise to install it in the headlight
housing.
8121zMaintenance

The headlight cable could
catch in the steering if it is
not routed correctly.
Use the appropriate retaining
clips to secure electric wires at
the back of the headlight.
Push the bulb housing into
mounts 4on the frame. Install securing screws
1at
both sides of the bulb hous-
ing.
Replacing brake light and
rear light bulb
If it is not standing firmly,
the motorcycle could topple
in the course of the operations
described below.
Always make sure that the
motorcycle is stable and firmly
supported.
Make sure the ground is level
and firm and place the motor-
cycle on its stand. Switch off the ignition.
Remove the seat ( 66)
Remove screw
1.
Pull the bulb housing to the
rear until it is clear of holders 2.
8122zMaintenance

Lighting
Bulb for high-beam headlight H7 / 12 V / 55 W
Bulb for low-beam headlight H7 / 12 V / 55 W
Bulb for parking light W5W / 12 V / 5 W
Bulb for tail light/brake light P21W / 12 V / 21 W
Bulbs for flashing turn indicators, front R10W / 12 V / 10 Wwith OE White turn indicators: RY10W / 12 V / 10 W
Bulbs for flashing turn indicators, rear R10W / 12 V / 10 W with OE White turn indicators: RY10W / 12 V / 10 WFrameFrame type Light alloy weldment with bolt-on tubular steel
rear frame
Type plate location Frame cross-tube, rear
VIN location Frame side section, front right
10147zTechnical data

A
Abbreviations and symbols, 6
ABSSelf-diagnosis, 74
Warning, 31
Anti-theft alarm, 18 Warning, 42
ASC Self-diagnosis, 74
Switching off, 58
Switching on, 58
Warning, 35
B
Battery Battery compartment, 13, 128
Charging battery when
connected, 127
Charging battery when
disconnected, 128
Installation, 129
Removal, 129
Technical data, 146
Warning for battery charge
current, 27 Brake fluid
Checking level, front, 13, 103
Checking level, rear, 13, 104
Brake pads Checking front, 102
Checking rear, 103
Running in, 75
Brakes Adjusting handbrake lever, 59
Checking operation, 101
Technical data, 143
Bulbs General instructions, 118
Replacing brake-light bulb, 122
Replacing front turn indicator
bulbs, 124
Replacing high-beam headlight
bulb, 118
Replacing low-beam headlight
bulb, 118
Replacing parking-light
bulb, 120
Replacing rear light bulb, 122
Replacing rear turn indicator
bulbs, 124 Technical data, 147
Warning for bulb failure, 28
C
Case Adapting, 95
Adjusting, 93
Closing, 92
Installing, 94
Opening, 92
Removing, 93
Checklist, 72
Clock Adjusting, 46
Clutch Adjusting clutch lever, 59
Checking level, 11, 105
Checking operation, 105
Technical data, 141
Confirmation of maintenance work, 154
Coolant Temperature gauge, 22
Warning, 26
Currency, 7
12161zIndex