heating BMW X5 3.0I 2006 E53 Owner's Manual
[x] Cancel search | Manufacturer: BMW, Model Year: 2006, Model line: X5 3.0I, Model: BMW X5 3.0I 2006 E53Pages: 202, PDF Size: 4.13 MB
Page 19 of 202
19n
OverviewControlsMaintenanceRepairsDataIndex
Indicator and warning lamps Technology that monitors itself Indicator and warning lamps that are
identified by
+ are tested for proper
functioning whenever the ignition key is
turned. They each light up once for dif-
ferent periods of time.
If a malfunction should occur in one of
the monitored systems, the corre-
sponding lamp will not go out after the
engine is started or it will light up while
the vehicle is moving. The section
below will instruct you on what to do in
this situation.
Red: stop immediately
Battery charge current
+
The battery is not being
charged. There is a malfunction
of the alternator drive belt or in the
charging circuit of the alternator. Have
the system checked immediately.
If the drive belt is defective, do not
continue driving. The engine could
be damaged due to overheating. When
the drive belt is defective, you will also
have to exert increased steering
effort.<
Engine oil pressure
+
Stop immediately and switch off
the engine. Check the engine oil
level; top up as required. If the oil level
is correct: have the system checked
immediately.
Do not continue driving. The
engine could be damaged due to
inadequate lubrication.<
Handbrake
*/
brake hydraulic system
+
Lights up with handbrake
engaged.
For additional information, refer to
page64
Lights up although the handbrake is
released: stop immediately. The brake
fluid in the reservoir has fallen to below
the minimum level. At the same time, a
considerably longer brake pedal travel
may be noticeable. Have the system
checked immediately.
During continued driving,
increased brake pedal pressure
may be necessary and considerably
longer braking distances may result.
Please remember to adapt your driving
style accordingly.<
Before continuing your journey, be sure
to read the notes on pages140
and155.
Also lights up in the Check Control with
the message CHECK BRAKE LININGS.
Display of the previously
described malfunction in Cana-
dian models.
Page 35 of 202
35n
OverviewControlsMaintenanceRepairsDataIndex
LiftgateOpening from outside Press the button, refer to arrow:
The liftgate opens slightly.
The cargo area is illuminated whenever
the liftgate is opened, refer also to
page103.
With the liftgate open, the dis-
tance from the ground to the
upper edge is more than 6.6 ft/2 m.
Please remember this, e.g. when open-
ing the liftgate in a garage.<530de245
Opening from inside Press this button to open the liftgate
when the vehicle is stationary.
If pointed or sharp-edged objects
could strike the rear window while
driving, be sure to provide protection
around all edges. Failure to do so could
result in damage to the heating conduc-
tors of the rear window.<
For information on the cargo area cover
and on other details in the cargo area,
refer to Cargo area, beginning on
page124.530de415
Manual release In the event of an electrical malfunction,
you can release the liftgate manually:
1. Remove the plastic plug from inside
the cargo area and pull toward the
interior, refer to arrow. The liftgate
will be released
2. Reinstall the plug. 530de316
Page 52 of 202
52n
Heated seats
*
Steering wheel
Front The seat cushion and backrest can be
heated when the ignition key is in posi-
tion 2.
You can call up different heating modes
by repeatedly pressing the button.
You can also switch off the higher heat-
ing modes directly:
Press the button and hold it slightly
longer.530de417
Rear The operating concept is the same as
for the front heated seats. You can
select between two heating modes.530de234
Adjustments The steering wheel can be moved in
any of four directions. Adjust the steer-
ing wheel by moving the control lever in
the desired direction.
Do not adjust the steering wheel
while the vehicle is moving. There
is a risk of accident from unexpected
movement.<
To store the steering wheel setting,
refer to Seat, mirror and steering wheel
memory on page50. 530de255
Page 54 of 202
54n
Mirrors1 Adjustments
2 Switching to the other mirror or to the
automatic parking function
*
3 Folding mirrors in and out
*
To store the mirror settings, refer to
Seat, mirror and steering wheel memory
on page50.Adjusting manuallyThe mirrors can also be adjusted manu-
ally by pressing the edges of the mirror
glass.530de256
Folding mirrors in and out Pressing button 3 allows you to fold
mirrors in and out up to a speed of
6 mph/10 km/h. This is advantageous,
for example, in narrow streets or for
bringing mirrors that have been manu-
ally folded-in back into the correct posi-
tion.
Before going through a car wash,
fold the exterior mirrors inward
manually or using button 3; otherwise
they could be damaged, depending on
the width of the car wash system.
heated when the motor is running or the
ignition is switched on.
Interior rearview mirror To reduce glare from vehicles behind
you when you are driving at night, tilt
the mirror by turning the button.530us244
Page 105 of 202
105n
OverviewControlsMaintenanceRepairsDataIndex
Air conditioner Temperature
The graduations on the dial
provide general reference val-
ues for the interior tempera-
ture. 707/226 is recom-
mended as a comfortable setting. After
driving begins, the selected tempera-
ture is reached as quickly as possible
and kept constant by the control sys-
tem.
Air distribution
You can direct air to flow onto
the windows , toward the
upper body and into the
footwell . All intermediate
settings are possible. In the setting,
there is a low flow of air onto the win-
dows to keep them free of condensa-
tion.
Air supply
You can adjust the air supply
through an infinitely-variable
range. The heating and venti-
lation become more and more
effective as the air supply settings are
increased. In the 0 setting, the blower
and climate control are switched off
and the outside air supply is blocked.
Rear window defroster
When the rear window
defroster is activated, the
LED lights up. The rear window
defroster switches off automatically.
Air conditioning
The air is cooled and dehu-
midified and — depending on
the temperature setting — warmed
again. Depending on the weather, the
windshield may fog over briefly when
the engine is started. You can reduce
condensation forming on the windows
by switching on the air conditioning.
During air conditioning, condensa-
tion forms, which then exits under
the vehicle. Traces of water on the
ground are therefore normal.<
Recirculated-air mode
You can respond to unpleas-
ant odors outside the vehicle
by temporarily switching off the outside
air supply. The system then recirculates
the air currently within the vehicle.
You can also use the button on the
steering wheel to switch over to the
recirculated-air mode, refer to page 23.
If the windows fog over in the
recirculated-air mode, switch the
recirculated-air mode off and increase
the air supply as required.<
Page 109 of 202
109n
OverviewControlsMaintenanceRepairsDataIndex
Automatic climate control
*
Tips for pleasant drivingFor nearly all conditions, AUTO pro-
gram 6 offers the optimal air distribution
and airflow volume. Select the interior
temperature that is comfortable for you.
Detailed setting options are described
for you in the following section.
Your BMW Sports Activity Vehicle
center can program the settings of
your vehicle in such a manner that,
when you unlock the vehicle with your
individualized key, your own personal-
ized setting for the automatic climate
control is initiated.< Automatic air distribution
The AUTO program
adjusts the airflow and dis-
tribution patterns for you while also
using your preselected temperature
setting as the basis for adjusting the
interior climate to adapt to external
influences: summer, winter.
Individual air distribution
You can cancel the AUTO
program by selecting spe-
cific air distribution patterns
for your personal comfort,
the automatic air supply
remains in operation. You can direct air
to flow onto the windows , toward
the upper body , and into the foot-
well . You can reactivate the auto-
matic air distribution mode by pressing
the AUTO button.
Temperature
Set the desired tempera-
ture individually on the
driver's and front passen-
ger side.
The automatic climate control adjusts
this temperature as quickly as possible
at any time of year, if necessary with the
maximum cooling or heating capacity,
and then keeps it constant.
When switching between differ-
ent temperature settings in rapid
succession, the automatic climate con-
trol does not have sufficient time to
adjust the set temperature.<
To change the units of measure in the
display 7/6, refer to page73 or80.Air supply
In the AUTO program,
the air supply is automati-
cally controlled, and AUTO appears on
the display 9, refer to overview on
page107. You can vary the air supply
by pressing the left or right half of the
button. When your setting is displayed
as bars, the automatic air supply is
switched off. Automatic air distribution
maintains its setting. You can reactivate
the automatic air supply by pressing the
AUTO button.
When you press the left side of the but-
ton during operation at minimum blower
speed, all displays are canceled: the
blower, heating and air conditioner are
switched off. The outside air supply is
closed. You can switch the system back
on by pressing any button of the auto-
matic climate control, except the MAX
button 16.
Defrosting windows and removing
condensation
Quickly remove ice and
condensation from the
windshield and front side windows.
Page 110 of 202
110n
Automatic climate control
*
Air conditioning
The air is cooled and
dehumidified and —
depending on the temperature setting —
warmed again. Depending on the
weather, the windshield may fog over
briefly when the engine is started. You
can reduce condensation forming on
the windows by switching on the air
conditioning.
During air conditioning, condensa-
tion forms, which then exits under
the vehicle. That traces of water on the
ground are therefore normal.<
Maximum cooling
Maximally cooled air is
obtained as quickly as possi-
ble from an outside temperature above
327/06 and with the engine running.
The automatic climate control changes
over to the lowest temperature and
switches into the recirculated-air mode.
The maximum air quantity only flows
out of the vents for the upper body.
Therefore, open these vents for maxi-
mum cooling.
AUC Automatic recirculated-air
control
You can respond to
unpleasant odors or pollut-
ants in the immediate environment by
shutting off the supply of outside air.
The system then recirculates the air
currently within the vehicle. In AUC
operating mode, a sensor detects pol-
lutants in the external air and controls
the shut-off automatically.
Press the button repeatedly to run
through the following control sequence
>LEDs off: outside air supply opera-
tional
>Left LED on, AUC mode: the system
detects pollutants in the outside air
and blocks the flow of air when nec-
essary. The system then recirculates
the air currently within the vehicle.
Depending on the air quality, the
automatic system then switches back
and forth between outside air supply
and recirculation of the air within the
vehicle
>Right LED on: the outside air supply
into the vehicle is shut off continu-
ously. The system then recirculates
the air currently within the vehicle.
You can also use the button on the
steering wheel to switch between Off
and recirculated-air mode or between
AUC and recirculated-air mode, refer to
page23.
If the windows fog over in the
recirculated-air mode, switch the
recirculated-air mode off and increase
the air supply as required.< Rear window defroster
When the rear window
defroster is activated, the
LED lights up. The rear window
defroster switches off automatically
after a while.
Residual heat
Press the button when the
motor is switched off, but
warm.
The heat stored in the engine is utilized
for heating the interior when the engine
has been switched off – while waiting at
a railroad crossing, for instance.
This function may be activated when
the outside temperature is below
approx. 597/156, the engine is at
operating temperature, and the battery
Page 130 of 202
130n
Cargo loading
Avoid overloading the vehicle
so that the permissible loading
capacity of the tires is not exceeded.
Overloading can lead to overheating
and increases the rate at which damage
develops inside the tires. The ultimate
result can assume the form of a sudden
air loss.<
Determining loading limit1. Locate the following statement on
your vehicle's placard
*:
The combined weight of occu-
pants and cargo should never
exceed XXX lbs. or YYY kg, other-
wise the vehicle may be damaged
and unstable driving conditions may
result.<
2. Determine the combined weight of
the driver and passengers that will be
riding in your vehicle
3. Subtract the combined weight of the
driver and passengers from XXX lbs.
or YYY kg
530de225
4. The resulting figure equals the avail-
able amount of cargo and luggage
load capacity.
For example, if the XXX amount
equals 1,350 lbs. and there will be
five 150 lbs. passengers in your vehi-
cle, the amount of available cargo
and luggage load capacity is
600 lbs.:
1,350 lbs. minus 750 lbs. = 600 lbs.
5. Determine the combined weight of
luggage and cargo being loaded into
the vehicle. That weight may not
safely exceed the available cargo
and luggage load capacity calculated
in step 4
6. If your vehicle will be towing a trailer,
load from your trailer will be trans-
ferred to your vehicle. Consult the
manual for transporting a trailer to
determine how this may reduce the
available cargo and luggage load
capacity of your vehicle.
Page 190 of 202
Everything from A to ZDivided rear seat backrest,
refer to Folding rear seat
back124
Door keys30
Door lock33
DOT Quality Grades145
Draft-free
ventilation106,111
Driving lamps, refer to
Parking lamps/low
beams100
Driving notes
breaking-in136
driving hints137,138
Driving on poor roads138
Driving stability control92
Driving tips, refer to Driving
notes137
Driving your X5138
Dry air, refer to Air
conditioning105,110
DSC Dynamic Stability
Control92
warning lamp22
DVD changer, refer to
Owner's Manual for Radio/
Onboard Computer
Dynamic Brake Control
DBC91
indicator lamp21Dynamic Stability Control
DSC92
warning lamp22
E
EBV Electronic brake-force
distribution91
Electrical defect
liftgate35
tailgate36
Electrical malfunction
automatic transmission
with Steptronic67
door lock33
driver's door33
fuel filler door24
panorama glass roof42
Electric steering wheel
adjustment52
Electronic brake-force distri-
bution EBV91
Electronic Stability Program
ESP, refer to DSC Dynamic
Stability Control92
Emergency call173
Emergency operation, refer
to Manual operation
driver's door33
fuel filler door24
liftgate35
panorama glass roof42
tailgate36Emergency Service, refer to
Roadside Assistance173
Energy-conscious driving,
refer to Energy control74
Energy control74
Engine
breaking-in136
data180
electronic circuitry22
overheated, refer to
Coolant temperature
gauge76
speed74
starting62
switching off63
Engine compartment151
Engine coolant154
Engine oil152
additives, refer to
Specified engine oils153
filling capacity183
indicator/warning lamp19
specified engine oils153
Engine oil level152
indicator/warning lamp21
Engine oil pressure,
indicator/warning lamp19
Engine oil temperature
gauge75
Engine output, refer to
Engine specifications180Engine overheating, refer to
Coolant temperature
gauge76
Engine specifications180
Engine speed, refer to
Engine specifications180
Environmentally friendly
driving, refer to Energy
control74
ESP Electronic Stability
Program, refer to DSC
Dynamic Stability
Control92
Event Data Recorders157
Exhaust system137
Extended immobilizer
function88
Exterior mirrors53
automatic dimming
feature138
folding in and out54
External air, automatic
climate control110
F
Failure messages, refer to
Check Control77
Failure of a current
consumer172
False alarms, refer to
Avoiding unintentional
alarms39
Page 192 of 202
Everything from A to ZHead restraints47
adjusting47
installing in front48
removing and installing in
rear48
removing in front48
sitting safely43
Heated mirrors54
Heated rear window
air conditioner105
automatic climate
control110
Heated seats52
Heated steering wheel53
Heater
rear window105,110
steering wheel53
Heating
exterior mirror54
residual heat
utilization110
seats52
Heating and
ventilation104,107
Heating while stationary110
Heavy cargo, refer to Cargo
loading131
Heavy-duty cargo straps,
refer to Cargo loading131
Height, refer to
Dimensions181Height adjustment
seats45,46
steering wheel52
High beams101
headlamp flasher68
indicator lamp22
replacing bulbs162
High temperatures137
Hill Descent Control HDC94
Hills138,140
Holder for cups120
Hood150
Horn14
Hotel function30
Hot exhaust system137
Hydraulic brake assistant,
refer to DBC91
Hydraulic system, brakes19
Hydroplaning137,147
I
Ice, refer to Outside
temperature warning
73
Identification, tire145
Ignition62
Ignition key30
Ignition key positions, refer
to Ignition lock62
Ignition lock62
Immobilizer function88
Imprint4Independent ventilation,
refer to Parked car
ventilation113
Indicating
elements15,17,18
Indicator/warning lamp
airbags57
alarm system38
automatic transmission
with Steptronic67
brakes155
coolant temperature76
DSC92
engine temperature76
fasten safety belts49
Flat Tire Monitor99
front fog lamps102
reserve75
self-leveling
suspension95
Indicator and warning lamps,
overview19
Indicator lighting, refer to
Instrument lighting102
Individual air distribution109
Individual settings, refer to
Vehicle Memory, Key
Memory61
Inflation pressure, tires, refer
to Tire inflation
pressure141Initializing, refer to Power
loss42
INSPECTION76
Instrument cluster15,17,18
refer to Cockpit14
Instrument lighting102
Instrument panel14
Integrated universal remote
control114
Interface socket for Onboard
Diagnostics157
Interior lamps103
remote control31
Interior mirror, automatic
dimming feature138
Interior motion sensor
39
switching off31,39
Interior rearview mirror54
compass117
Interlock, refer to Steering
lock engaged62
Intermittent operation of
wipers69,71
Interval Display, Service76
J
Jacking points for vehicle
jack170
Jumpering, refer to Jump
starting174
Jump starting174