light BMW Z4M ROADSTER 2007 E85 Owner's Manual
[x] Cancel search | Manufacturer: BMW, Model Year: 2007, Model line: Z4M ROADSTER, Model: BMW Z4M ROADSTER 2007 E85Pages: 50, PDF Size: 3.93 MB
Page 10 of 50
Cockpit
8
Cockpit
Around the steering wheel: controls and displays
For descriptions of equipment listed here
without a page reference, please refer to
the Owner's Manual for the BMW Z4 under the
respective term.<
2Folding exterior mirrors in or out
*
3Adjusting exterior mirrors
1
Opening and closing windows
4
Parking lamps
Low beams
Automatic headlamp control
*
5
Instrument lighting
ba5.book Seite 8 Mittwoch, 28. Februar 2007 1:09 13
Page 12 of 50
Cockpit
10
Instrument cluster
For descriptions of equipment listed here
without a page reference, please refer to
the Owner's Manual for the BMW Z4 under the
respective term.<
1Speedometer
2Indicator lamps for turn signals
3Indicator and warning lamps10
4Tachometer17
with indicator and warning lamps10
5Engine oil thermometer17
6Fuel gauge17
7Button for
>Displaying the clock
>Service interval display
8Button for
>Resetting trip odometer
>Setting the clock
9Display for
>Trip odometer/Odometer
>Clock
>Service interval
>ComputerIndicator and warning lamps
Technology that monitors itself
Indicator and warning lamps that are identified
by
+ are tested for proper functioning whenever
the ignition key is turned. They each light up
once for different periods of time.
If a malfunction occurs in one of the monitored
systems, the corresponding lamp does not go
out after the engine has started, or it lights up
again while the vehicle is in motion. More infor-
mation can be found on the specified pages or
in the Owner's Manual for the BMW Z4 under
the respective terms.
Turn signal indicators
Battery charge current
+
Headlamp flasher/High beams
Engine oil pressure/
Engine oil level
+28
ba5.book Seite 10 Mittwoch, 28. Februar 2007 1:09 13
Page 13 of 50
At a glance
Controls
Driving tips
Mobility Reference
11
Colors
The indicator and warning lamps can light up in
various colors and combinations.
>Red:
Stop the vehicle immediately
or
an important reminder
>Red and yellow:
Continue driving cautiously
>Yellow:
Have the system checked soon
or
for your information
>Green or blue:
For your information Antilock Brake System ABS/Driving
stability control systems
+
Antilock Brake System ABS/Driving
stability control systems for Canadian
models
Brake system
+
Brake warning lamp for Canadian mod-
els
Brake pads
+
Parking lamps/Low beams
Flat Tire Monitor
* +18
Tire Pressure Monitor
* +18
Airbags
+
Safety belt reminder
Defective bulb
Doors or luggage compartment lid/tail-
gate open
Engine electronics
+
Malfunction in the engine electronics.
You can continue to drive with reduced
engine output. Please have the system
inspected by your BMW center.
Service engine soon
+
Service engine soon indicator lamp for
Canadian models
Dynamic Stability Control DSC
+18
Add coolant
Add washer fluid
Coolant temperature17
Check gas cap
+
ba5.book Seite 11 Mittwoch, 28. Februar 2007 1:09 13
Page 20 of 50
Technology for driving comfort and safety
18
Technology for driving comfort and safety
Driving stability control
systems
In contrast to the descriptions in the Owner's
Manual for the BMW Z4, your BMW Z4 M Road-
ster/Z4 M Coupe does not feature Dynamic
Traction Control DTC.
Dynamic Stability Control DSC
DSC prevents slip at the drive wheels while
starting off and accelerating the vehicle. DSC
also recognizes unstable vehicle conditions,
such as fishtailing or nose-diving. In these
cases, and subject to physical limits, DSC helps
to keep the vehicle on a steady course by
reducing engine speed and by applying brakes
at individual wheels.
The laws of physics cannot be repealed
even with DSC. It will always be the
driver's responsibility to drive in a manner that
matches road conditions. Therefore, do not
limit the additional safety margin by practicing
risky driving.<
Deactivating DSC
Press the button; the DSC indicator lamp in the
instrument cluster lights up. No more interven-
tions to increase stability and forward momen-
tum are carried out.
To enhance vehicle stability, reactivate DSC as
soon as possible.
Activating DSC
Press the button briefly; the indicator lamp goes
out in the instrument cluster.
Checking
The indicator lamp flashes:
DSC controls the drive forces and
brake forces.
The indicator lamp is lit:
DSC is deactivated.
Flat Tire Monitor FTM*
In contrast to the descriptions in the Owner's
Manual for the BMW Z4, your BMW Z4 M Road-
ster/Z4 M Coupe is not equipped with Run-Flat
Tires. You should therefore observe the follow-
ing when you receive a flat tire warning.
Flat tire warning
The warning lamp in the instrument
cluster lights up in red. A signal also
sounds. There is a flat tire or substantial
loss of tire pressure.
1.Reduce speed and pull the vehicle over
carefully. Avoid strong braking and steering
maneuvers.
2.Determine which tire is damaged. To do
this, check the tire inflation pressure using
the M Mobility System, refer to Restoring
tire inflation pressure on page33.
3.Use the M Mobility System to repair the flat
tire, refer to page31.
Tire Pressure Monitor TPM*
In contrast to the descriptions in the Owner's
Manual for the BMW Z4, your BMW Z4 M Road-
ster/Z4 M Coupe is not equipped with Run-Flat
Tires. Therefore, note the following if the sys-
tem warns of low tire inflation pressure.
ba5.book Seite 18 Mittwoch, 28. Februar 2007 1:09 13
Page 21 of 50
Reference
At a glance
Controls
Driving tips
Mobility
19
Warning of low tire inflation pressure
The warning lamp lights up in yellow. A
signal also sounds. There is a flat tire or
a significant loss of tire pressure in one
or more tires.
1.Reduce speed and pull the vehicle over
carefully. Avoid strong braking and steering
maneuvers.
2.Identify the damaged wheel or wheels. To
do this, check the tire inflation pressure
using the M Mobility System, refer to
Restoring tire inflation pressure on page33.
If the damaged wheel cannot be iden-
tified, contact your BMW center.<
3.Use the M Mobility System to repair the flat
tire, refer to page31.
Have the damaged tire replaced at the BMW
center or at a workshop that works according to
BMW repair procedures with correspondingly
trained personnel.
Power steering
In contrast to the descriptions in the Owner's
Manual for the BMW Z4, your BMW Z4 M Road-
ster/Z4 M Coupe is equipped with hydraulic
power steering.
ba5.book Seite 19 Mittwoch, 28. Februar 2007 1:09 13
Page 30 of 50
Under the hood
28
Under the hood
Important parts in the engine compartment
1Washer fluid reservoir for headlamp and
windshield washer system
2Filler neck for engine oil, refer to Adding
engine oil
3Jump-starting connection4Reservoir for brake fluid
5Coolant expansion tank
6Chassis ground, negative terminal
7Dipstick for engine oil, refer to Checking the
oil level
Engine oil
Like fuel consumption, engine oil consumption
depends on your driving style and the vehicle's
operating conditions.
Warning lamp
Engine oil pressure
The warning lamp lights up in red:
The engine oil pressure is too low.
Stop the vehicle immediately and
switch off the engine. Check the engine oil level
and top up if necessary. If the oil level is correct,
please contact your nearest BMW center or a
workshop that works according to BMW repair procedures with correspondingly trained per-
sonnel.
Do not continue driving, otherwise the
engine could sustain serious damage
from inadequate lubrication.<
Engine oil level
The warning lamp lights up in yellow
while you are driving. A signal also
sounds.
The oil level is at the absolute minimum; check
engine oil level using dipstick 7 and refill as
soon as possible. Do not drive more than
30 miles/50 km before refilling.
ba5.book Seite 28 Mittwoch, 28. Februar 2007 1:09 13
Page 31 of 50
Reference
At a glance
Controls
Driving tips
Mobility
29
The warning lamp lights up in yellow
after the engine is switched off. A signal
also sounds.
Check the engine oil level using dipstick7 at the
earliest opportunity, e.g. when you stop to
refuel, and refill engine oil.
The warning lamp lights up in yellow
within 30 seconds after the engine is
started:
The oil level sensor is defective. Have the sys-
tem checked as soon as possible.
Checking the oil level
1.Position the vehicle on a level surface.
2.Switch off the engine when it is at operating
temperature.
3.After approx. 1 minute, pull dipstick 7 out
and wipe it off with a clean, lint-free cloth,
paper towel or something similar.
4.Carefully push the dipstick fully into its tube,
then pull it out again.
The oil level must be between the two
marks on the dipstick.
The oil volume between the two marks on the
dipstick corresponds to approx. 1.4 US quarts/
1.3 liters.
Adding engine oil
Do not add oil until the oil level has dropped
almost to the lower mark on the dipstick, refer to
Checking the oil level.
Do not add oil beyond the upper mark on
the dipstick, otherwise excessive oil can
lead to engine damage.<
Before you check the engine oil level after add-
ing oil, restart the engine and let it run to obtain
a correct reading. Then proceed as described
under Checking the oil level.
BMW engines are designed to operate
without oil additives; the use of additives
could even lead to damage in some cases. The
same applies to the transmission and differen-
tial as well as to the power steering.<
Continuous exposure to used oil has
caused cancer in laboratory tests. For this
reason, thoroughly wash any areas of skin that
have come into contact with oil using soap and
water.
Keep oils, greases, etc. out of the reach of chil-
dren and comply with the warnings on the con-
tainers. Otherwise, health hazards may result.<
Comply with the applicable environmen-
tal regulations concerning the disposal of
used oil.<
Recommendation: have the oil changed at your
BMW center.
Approved engine oils
The quality of the engine oil is extremely impor-
tant for the function and life of an engine. BMW
only approves specific oils after confirming their
suitability for use in its vehicles with extensive
testing.
ba5.book Seite 29 Mittwoch, 28. Februar 2007 1:09 13
Page 34 of 50
Replacing components
32 Corresponding information on using the
M Mobility System is also provided on the
device.<
Before using the M Mobility System, note
the information on the sealant bottle.<
Pull the sticker for the speed limit off the sealant
bottle and affix it to the steering wheel.
Please observe the expiry date on the
sealant bottle.<
Roadster
The M Mobility System is located on the right-
hand side of the cargo bay on the battery cover.
With the convertible top closed, fold the
convertible top compartment panel up to
remove the Mobility Set.<
To avoid any damage when opening the
convertible top, make sure that the con-
vertible top compartment panel in the cargo bay
has been folded down.<
Coupe: access to the Mobility Set
1.Turn the quick-release fastener counter-
clockwise.
2.Pull out the cover.When reinstalling the cover, make sure
that its tabs are inserted into the corre-
sponding cut-outs in the cargo bay trim panel.<
The M Mobility System is located on the right-
hand side of the cargo bay in a compartment on
top of the battery.
The M Mobility System consists of
1Sealant bottle and sticker with speed limit
2Filler hose from sealant bottle to wheel
3Cable and connector to cigarette lighter
socket
4Mounting for sealant bottle
5Compressor
6On/off switch
7Gauge for indicating tire inflation pressure
8Button for reducing tire inflation pressure
ba5.book Seite 32 Mittwoch, 28. Februar 2007 1:09 13
Page 35 of 50
Reference
At a glance
Controls
Driving tips
Mobility
33
9Connecting hose for connecting compres-
sor and sealant bottle or compressor and
wheel
Connector, cable and connecting hose are
attached to the bottom of the compressor.
Using the M Mobility System
To repair a flat tire with the M Mobility System,
proceed as follows:
>Fill sealant into wheel
>Distribute sealant
>Restore tire inflation pressure
Filling sealant into wheel
Strictly adhere to the specified order, oth-
erwise highly pressurized sealant could
escape.<
1.Shake sealant bottle.
2.Screw hose9 onto connection of sealant
bottle.
3.Unscrew and remove dust cap from valve of
defective wheel and screw filler hose2 of
sealant bottle onto valve.
4.Insert sealant bottle on compressor hous-
ing so that the bottle is in an upright posi-
tion.
5.Make sure that the device is switched off,
position 0.
6.Insert connector 3 into cigarette lighter
socket inside the vehicle.
7.With the ignition switched on:
Switch on the device and allow it to run for
approx. 3 minutes to fill the wheel with seal-
ant. It is not important what inflation pres-
sure the tire has after this.8.Switch off device.
9.Remove connecting hoses from connection
of sealant bottle and tire valve.
Stow the M Mobility System in the vehicle
again.
Distributing sealant
Immediately drive approx. 2 miles/3 km so that
the sealant is evenly distributed in the tire.
Do not exceed a speed of 35 mph or
60 km/h. Do not drive slower than 12 mph
or 20 km/h if possible.<
Restoring tire inflation pressure
1.After approx. 2 miles/3 km, pull over at a
suitable location.
2.Screw compressor hose9 directly onto tire
valve.
3.Insert connector 3 into cigarette lighter
socket inside the vehicle.
4.Correct tire inflation pressure to 29 psi/
200 kPa. With the ignition switched on:
>To increase inflation pressure: switch on
the compressor, position I. To check the
current pressure setting, briefly switch
off the device.
Do not allow the compressor to run
for more than 10 minutes, otherwise
the device will overheat and may be dam-
aged.<
>To reduce inflation pressure: press but-
ton 8.
If the inflation pressure is not maintained,
drive the vehicle again, refer to Distribut-
ing sealant. Then repeat steps 1 to 4 once.
Using the M Mobility System can be ineffective
with tire punctures larger than approx. 1/6 in/
4 mm. Please contact the nearest BMW center
or a workshop that works according to BMW
repair procedures with correspondingly trained
personnel if the tire cannot be made ready for
driving with the M Mobility System.<
The tire inflation pressure must be at least
29 psi/200 kPa. Otherwise do not con-
tinue driving.<
ba5.book Seite 33 Mittwoch, 28. Februar 2007 1:09 13