light BUICK CENTURY 1994 User Guide

Turn SignallHeadlight Beam Lever
.1
The lever on the left side of the steering column
includes your:
Turn Signal and Lane Change Indicator
0 Headlight High-Low Beam & Passing Signal
a Windshield Wipers
0 Windshield Washer
Cruise Control (Option)
Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for
left) positions. These positions allow you
to signal a turn or a lane change.
To signal a
turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
89
ProCarManuals.com

I I A green arrow on the
instrument panel will flash
in the direction of the turn
or lane change.
To signal a lane change,
just raise
or lower the lever
until the green arrow starts
to flash. Hold
it there until
you complete your lane
change. The lever will
return by itself when you
release it.
As you signal a turn or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace
it to help avoid an
accident. If the green arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses” in the Index)
and for burned-out bulbs.
nrn Signal Reminder
If your turn signal is left on for more than 3/4 of a mile,
a chime will sound.
To turn off the chime, move the turn
signal lever
to the off position.
Operation of Lights
Although your vehicle’s lighting system (headlights,
parking lights, fog lamps, side marker lights and
taillights) meets all applicable federal lighting
requirements, certain states and provinces may apply
their own lighting regulations that may require special
attention before you operate these lights.
For example, some jurisdictions may require that you
operate your fog lamps only when your lower beam
headlights are also on, or that headlights be turned on
whenever you must use your windshield wipers. In
addition, most jurisdictions prohibit driving solely with
parking lights, especially at dawn
or dusk. It is
recommended that you check with your own state or
provincial highway authority for applicable lighting
regulations.
90
ProCarManuals.com

Headlight High-Low Beam
BRIGHT
To change the headlights
from low beam to high
or
high to low, pull the turn
signal lever all the way
toward you. Then release it.
When the high beams are
on, this blue light on the
instrument panel also will
be on.
Windshield Wipers
You control the windshield wipers by turning the band
marked “WIPER.”
For a single wiping cycle, turn the band to “MIST.”
Hold it there until the wipers start, then let go. The
wipers will stop after one cycle.
If you want more
cycles, hold the band on
“MIST” longer.
91
ProCarManuals.com

You can set the wiper speed for a long or short delay
between wipes. This can be very useful in light rain
or
snow. Turn the band to choose the delay time. The
closer to
“LO,” the shorter the delay.
For steady wiping at low speed, turn the band away
from you
to the “LO” position. For high speed wiping,
turn the band further, to “HI.”
To stop the wipers, move
the band to
“OFF.”
Remember that damaged wiper blades may prevent you
from seeing well enough to drive safely. To avoid
damage, be sure
to clear ice and snow from the wiper
blades before using them. If they’re frozen to the
windshield, carefully loosen or thaw them.
If your
blades do become damaged, get new blades
or blade
inserts.
Heavy snow or ice can overload your wiper motor.
A
circuit breaker will stop the motor until it cools. Clear
away snow or ice to prevent an overload.
Windshield Washer
At the top of the turn signalheadlight beam lever there’s
a paddle with the word “PUSH” on it.
To spray washer
fluid on the windshield, push the paddle.
If you push the paddle less than one second, washer
fluid will spray three
to four times while the wiper
blades
cycle. If you push the paddle longer than one
second, washer fluid will spray as long
as the paddle is
held. When
you release the paddle, the wiper blades will
cycle three to four more times to clear the window and
then either stop or return to your preset speed.
Driving without washer fluid can be dangerous.
A bad
mud splash can
block your vision. You could hit another
vehicle or go off the road. Check your washer fluid level
often.
92
ProCarManuals.com

To Set Cruise Control
1. Move the Cruise
Control switch
to “ON.”
2. Get up to the speed you want.
CRUISE
3. Push in the “SET”
button at the end of the
lever and release it.
4.
5.
The CRUISE light on
the instrument panel
will come on.
Take your foot
off the
accelerator pedal.
95
ProCarManuals.com

To Get Out of Cruise Control
There are two ways to turn
off the Cruise Control:
-
1. Step lightly on the brake
pedal,
OR
2. Move the Cruise switch
to
“OFF.”
To Erase Speed Memory
When you turn off the Cruise Control or the ignition,
your Cruise Control set speed memory is erased.
Lights
I These switches control the
following light systems:
Headlights
Parking Lights
Side Marker Lights
Taillights
License Plate Lights
Instrument Panel Lights
To turn on the headlights, press the switch with the light
symbol.
Press the switch marked
“P’ to turn on the parking
lights.
Press
“OFF” to turn off all lights.
98
ProCarManuals.com

Interior/Instrument Panel Lights
You can brighten or dim the
instrument panel lights by
rotating the control up or
down. To turn on the
interior courtesy lights,
rotate the control all the
way up to
“HI.”
Headlight ccOn99 Warning
If you open the door while leaving the lights on, you
will hear
a warning chime.
Daytime Running Lights (Canada Only)
The Canadian Federal Government has decided that
“Daytime Running Lights” (DRL) are a useful feature,
in that DRL can make your vehicle more visible to
pedestrians and other drivers during daylight hours.
DRL are required on new vehicles sold in Canada.
Your DRL work with a light sensor on top of the
instrument panel. Don’t cover it up.
The low beam headlights will come on at reduced
brightness in daylight when:
0 the ignition is on,
0 the headlight switch is off, and
0 the parking brake is released.
At dusk, the exterior lights will come on automatically
and the low beams will change to full brightness. At
dawn, the exterior lights will go out and the low beams
will change to the reduced brightness
of DRL (if the
headlight switch is off).
99
ProCarManuals.com

Of course, you may still turn on the headlights any time
you need to.
To idle your vehicle with the DRL off, set the parking
brake while the ignition
is in the “Off’ or “Lock”
position. Then start the vehicle. The
DRL will stay off
until you release the parking brake.
Press the switch to turn the
map light on and off.
Front Seat Reading Lights (Option)
.. . , ..
L
Press the switch to turn the front seat reading lights on
or off.
100
ProCarManuals.com

Press the switches on the front of the mirror to turn on
the reading lights.
Rear Reading Lights (Wagon)
This light will go on when you open the liftgate. To turn
on the light when the liftgate is closed, press the switch.
1 A1
ProCarManuals.com

Interior Lights Delay
When you pull on the driver’s outside door handle, the
dome and courtesy lights will go on and stay on for
about
40 seconds, or until you turn the ignition on.
If you pull on the driver’s inside door handle within 30
seconds of switching off the ignition, the interior lights
will go
on and stay on for about 5 seconds, to allow you
to unlock your door(s).
Courtesy Lights
When any door is opened, several lights go on. These
lights are under
the instrument panel. Optional lights are
on the rear doors. They make it easy for you to enter and
leave
the vehicle. You also can turn these lights on by
rotating the interior lights switch to
“HI.”
Mirrors
Inside Mirror
When you are sitting in a comfortable driving position,
adjust the mirror
so you can see clearly behind you car.
The day-night adjustment allows
you to reduce glare
from lights behind you, pull the lever toward
you to the
night position.
1 A3
ProCarManuals.com