remote start BUICK ENCLAVE 2009 Owner's Guide

ProblemRecommended Action
No power. The ignition might not be turned
ON/RUN or in ACC/ACCESSORY.
The picture does not ll the screen.
There are black borders on the top
and bottom or on both sides or it
looks stretched out. Check the display mode settings in
the setup menu by pressing the
display menu button on the remote
control.
In auxiliary mode, the picture moves
or scrolls. Check the auxiliary input
connections at both devices.
The remote control does not work. Check to make sure there is no obstruction between the remote
control and the transmitter window.
Check the batteries to make sure
they are not dead or installed
incorrectly.
After stopping the player, I push
Play but sometimes the DVD starts
where I left off and sometimes at
the beginning. If the stop button was pressed
one time, the DVD player resumes
playing where the DVD was
stopped. If the stop button was
pressed two times the DVD player
begins to play from the beginning of
the DVD.
The auxiliary source is running but
there is no picture or sound. Check that the RSE video screen is
in the auxiliary source mode.
Check the auxiliary input
connections at both devices.
Instrument Panel 3-109

A. Radiator Pressure Cap. See
Cooling System on page 5-16.
B. Engine Coolant Recovery Cap.
SeeCooling System on
page 5-16.
C. Remote Negative (−) Terminal.
SeeJump Starting on page 5-28.
D.Underhood Fuse Block on
page 5-94.
E. Remote Positive (+) Terminal.
SeeJump Starting on page 5-28.
F.Power Steering Fluid on
page 5-22.
G. Engine Oil Fill Cap. See “When
to Add Engine Oil” underEngine
Oil on page 5-11.
H. Engine Oil Dipstick. See
“Checking Engine Oil” under
Engine Oil on page 5-11.
I. Automatic Transmission Fluid
Dipstick. See “Checking the
Fluid Level” underAutomatic
Transmission Fluid on page 5-15.
J. Brake Master Cylinder Reservoir.
See “Brake Fluid” underBrakes
on page 5-24.K.Engine Air Cleaner/Filter on
page 5-14.
L. Windshield Washer Fluid
Reservoir. See “Adding Washer
Fluid” underWindshield
Washer Fluid on page 5-23.
Engine Oil
Checking Engine Oil
It is a good idea to check the
engine oil every time you get fuel. In
order to get an accurate reading,
the oil must be warm and the vehicle
must be on level ground.
The engine oil dipstick handle is a
yellow loop. SeeEngine
Compartment Overview on
page 5-10for the location of the
engine oil dipstick.
1. Turn off the engine and give the
oil several minutes to drain back
into the oil pan. If you do not
do this, the oil dipstick might not
show the actual level.2. Pull out the dipstick and clean it
with a paper towel or cloth, then
push it back in all the way.
Remove it again, keeping the tip
down, and check the level.
When to Add Engine Oil
If the oil is below the cross-hatched
area at the tip of the dipstick,
add at least one quart/liter of the
recommended oil. This section
explains what kind of oil to use. For
engine oil crankcase capacity, see
Capacities and Specifications on
page 5-98.
Notice:Do not add too much oil.
If the engine has so much oil
that the oil level gets above the
cross-hatched area that shows
the proper operating range,
the engine could be damaged.
Service and Appearance Care 5-11

4. Open the hoods and locate the
positive (+) and negative (−)
terminal locations on the other
vehicle. Your vehicle has a
remote positive (+) and a
remote negative (−) jump
starting terminal. SeeEngine
Compartment Overview on
page 5-10for more information
on the terminal locations.
{CAUTION
Using a match near a battery can
cause battery gas to explode.
People have been hurt doing this,
and some have been blinded. Use
a ashlight if you need more light.
Be sure the batteries have
enough water. You do not need to
add water to the ACDelco
®
battery (or batteries) installed in
your new vehicle. But if a battery
(Continued)
CAUTION (Continued)
has ller caps, be sure the right
amount of uid is there. If it is
low, add water to take care of that
rst. If you do not, explosive gas
could be present.
Battery uid contains acid that
can burn you. Do not get it on
you. If you accidentally get it in
your eyes or on your skin, ush
the place with water and get
medical help immediately.
{CAUTION
Fans or other moving engine
parts can injure you badly. Keep
your hands away from moving
parts once the engine is running.5. Check that the jumper cables do
not have loose or missing
insulation. If they do, you could
get a shock. The vehicles
could be damaged too.
Before you connect the cables,
here are some basic things you
should know. Positive (+) will go
to positive (+) or to a remote
positive (+) terminal if the vehicle
has one. Negative (−) will go to a
heavy, unpainted metal engine
part or to a remote negative (−)
terminal if the vehicle has one.
Do not connect positive (+) to
negative (−) or you will get
a short that would damage the
battery and maybe other
parts too. And do not connect
the negative (−) cable to
the negative (−) terminal on the
dead battery because this
can cause sparks.
Service and Appearance Care 5-29

10. Now start the vehicle with the
good battery and run the
engine for a while.
11. Try to start the vehicle that had
the dead battery. If it will not
start after a few tries, it probably
needs service.
Notice:If the jumper cables are
connected or removed in the
wrong order, electrical shorting
may occur and damage the
vehicle. The repairs would not be
covered by your warranty. Always
connect and remove the jumper
cables in the correct order,
making sure that the cables do not
touch each other or other metal.A. Heavy, Unpainted Metal Engine
Part or Remote Negative (−)
Terminal
B. Good Battery or Remote
Positive (+) and Remote
Negative (−) Terminals
C. Dead Battery or Remote
Positive (+) TerminalTo disconnect the jumper cables
from both vehicles, do the following:
1. Disconnect the black negative (−)
cable from the vehicle that had
the dead battery.
2. Disconnect the black negative (−)
cable from the vehicle with the
good battery.
3. Disconnect the red positive (+)
cable from the vehicle with the
good battery.
4. Disconnect the red positive (+)
cable from the other vehicle. Jumper Cable Removal
Service and Appearance Care 5-31

3. Press the Remote Keyless
Entry (RKE) transmitter’s LOCK
and UNLOCK buttons at the
same time for approximately
ve seconds. The horn sounds
twice to signal the receiver
is in relearn mode and TIRE
LEARNING ACTIVE message
displays on the DIC screen.
4. Start with the driver side
front tire.
5. Remove the valve cap from the
valve cap stem. Activate the
TPMS sensor by increasing or
decreasing the tire’s air pressure
for ve seconds, or until a horn
chirp sounds. The horn chirp,
which may take up to 30 seconds
to sound, conrms that the sensor
identication code has been
matched to this tire and wheel
position.
6. Proceed to the passenger side
front tire, and repeat the
procedure in Step 5.7. Proceed to the passenger side
rear tire, and repeat the
procedure in Step 5.
8. Proceed to the driver side rear
tire, and repeat the procedure in
Step 5. The horn sounds two
times to indicate the sensor
identication code has been
matched to the driver side rear
tire, and the TPMS sensor
matching process is no longer
active. The TIRE LEARNING
ACTIVE message on the DIC
display screen goes off.
9. Turn the ignition switch to
LOCK/OFF.
10. Set all four tires to the
recommended air pressure level
as indicated on the Tire and
Loading Information label.
11. Put the valve caps back on the
valve stems.Tire Inspection and
Rotation
We recommend that you
regularly inspect the vehicle’s
tires, including the spare tire, if
the vehicle has one, for signs of
wear or damage. SeeWhen It Is
Time for New Tires on page 5-50
for more information.
Tires should be rotated every
5,000 to 8,000 miles (8 000 to
13 000 km). SeeScheduled
Maintenance on page 6-3.
The purpose of a regular tire
rotation is to achieve a uniform
wear for all tires on the vehicle.
This will ensure that the vehicle
continues to perform most like it
did when the tires were new.
Any time you notice unusual
wear, rotate the tires as soon
as possible and check wheel
alignment. Also check for
damaged tires or wheels.
5-48 Service and Appearance Care

Navigation System
If your vehicle has a navigation
system, use of the system
may result in the storage of
destinations, addresses, telephone
numbers, and other trip information.
Refer to the navigation system
operating manual for information on
stored data and for deletion
instructions.
Radio Frequency
Identication (RFID)
RFID technology is used in some
vehicles for functions such as
tire pressure monitoring and ignition
system security, as well as in
connection with conveniences such
as key fobs for remote door
locking/unlocking and starting, and
in-vehicle transmitters for garage
door openers. RFID technology in
GM vehicles does not use or record
personal information or link with
any other GM system containing
personal information.
7-16 Customer Assistance Information

Remote Vehicle Start............. 2-5
Removing the Flat Tire and
Installing the Spare Tire.....5-74
Removing the Spare Tire and
Tools..............................5-72
Replacement Bulbs..............5-35
Replacement Parts,
Maintenance....................6-14
Replacement, Windshield......5-35
Reporting Safety Defects
Canadian Government.......7-13
General Motors................7-13
United States
Government..................7-12
Restraint System Check
Checking the Restraint
Systems.......................1-58
Replacing Restraint System
Parts After a Crash........1-59
Retained Accessory Power....2-22
Roadside
Assistance Program............ 7-6
Rocking Your Vehicle to Get
it Out ..............................4-16
Routing, Engine Drive Belt....6-15
Running the Vehicle While
Parked............................2-31S
Safety Belt Reminders..........3-30
Safety Belts
Care of ...........................5-86
How to Wear Safety Belts
Properly.......................1-16
Lap-Shoulder Belt.............1-20
Safety Belt Extender.........1-25
Safety Belt Use During
Pregnancy....................1-25
Safety Belts Are for
Everyone.....................1-12
Safety Warnings and Symbols.... iii
Scheduled Maintenance.......... 6-3
Seats
Heated and Cooled Seats.... 1-4
Heated Seats..................... 1-4
Manual Lumbar.................. 1-3
Memory, Mirrors................. 1-5
Power Lumbar ................... 1-4
Power Seats...................... 1-3
Rear Seat Operation........... 1-8
Reclining Seatbacks............ 1-6
Third Row Seat................1-10
Second Row Center
Console..........................2-50Secondary Latch System.......5-78
Securing a Child Restraint
Rear Seat Position............1-40
Right Front Seat
Position.......................1-42
Security Light......................3-39
Service................................ 5-3
Accessories and
Modications.................. 5-3
Adding Equipment to the
Outside of the Vehicle..... 5-4
California Perchlorate
Materials Requirements.... 5-4
California Proposition 65
Warning......................... 5-3
Doing Your Own Work........ 5-4
Engine Soon Lamp...........3-36
Publications Ordering
Information...................7-13
Service, Scheduling
Appointments..................... 7-8
Servicing Your
Airbag-Equipped Vehicle....1-56
Setting the Clock.................3-65
Sheet Metal Damage............5-89
Shifting Into Park
.................2-28
Shifting Out of Park..............2-29
INDEX i-9

Signals, Turn and
Lane-Change..................... 3-7
Spare Tire
Compact.........................5-83
Installing..........................5-74
Removing........................5-72
Storing............................5-80
Specications, Capacities......5-98
Speedometer.......................3-30
StabiliTrak
®Indicator Light.....3-35
Stabilitrak®System................ 4-5
Start Vehicle, Remote............. 2-5
Starting the Engine..............2-22
Steering............................... 4-8
Steering Wheel Controls,
Audio............................3-113
Steering Wheel, Power Tilt
Wheel and Telescopic
Steering Column................ 3-6
Steering Wheel, Tilt and
Telescopic......................... 3-6
Storage Areas
Cargo Management
System........................2-52
Center Console
Storage Area................2-49Storage Areas (cont.)
Cupholders......................2-49
Glove Box.......................2-49
Instrument Panel
Storage Area................2-49
Luggage Carrier...............2-51
Rear Seat Armrest............2-51
Second Row Center
Console.......................2-50
Storing the Tire Sealant and
Compressor Kit................5-70
Stuck in Sand, Mud, Ice,
or Snow..........................4-15
Sun Visors..........................2-16
Sunroof..............................2-53
T
Tachometer.........................3-30
Taillamps
Turn Signal, Stoplamps and
Sidemarker Lamps.........5-34
Telescopic Steering Column,
Power Tilt Wheel................ 3-6
Telescopic Wheel................... 3-6
Theft-Deterrent, Radio.........3-113Theft-Deterrent Systems........2-16
Content Theft-Deterrent.....2-16
PASS-Key
®III+ Electronic
Immobilizer...................2-18
PASS-Key
®III+ Electronic
Immobilizer Operation....2-18
Tilt Wheel............................. 3-6
Time, Setting.......................3-65
Tire
Pressure Light..................3-36
Tire Sealant
Storing............................5-70
Tires..................................5-36
Aluminum or
Chrome-Plated Wheels,
Cleaning......................5-88
Buying New Tires.............5-50
Chains............................5-56
Changing a Flat Tire.........5-71
Cleaning..........................5-89
Compact Spare Tire..........5-83
Different Size...................5-52
If a Tire Goes Flat............5-56
Ination - Tire Pressure.....5-42
Inspection and Rotation.....5-48
Installing the Spare Tire.....5-74
i-10 INDEX

Tires (cont.)
Pressure Monitor
Operation.....................5-45
Pressure Monitor System . . . 5-44
Removing the Flat Tire......5-74
Removing the Spare Tire
and Tools.....................5-72
Secondary Latch System . . . 5-78
Storing a Flat or Spare Tire
and Tools.....................5-80
Tire Sealant and
Compressor Kit.............5-57
Tire Sidewall Labeling.......5-37
Tire Terminology and
Denitions....................5-40
Uniform Tire Quality
Grading.......................5-52
Wheel Alignment and Tire
Balance.......................5-54
Wheel Replacement..........5-55
When It Is Time for New
Tires............................5-50
Tow/Haul Mode ....................2-26
Tow/Haul Mode Light............3-40Towing
Recreational Vehicle..........4-21
Towing a Trailer................4-24
Your Vehicle.....................4-21
Traction
Stabilitrak
®System............. 4-5
Transmission
Fluid, Automatic................5-15
Transmission Operation,
Automatic........................2-24
Turn and Lane-Change
Signals............................. 3-7
Turn Signal/Multifunction
Lever................................ 3-6
U
Ultrasonic Rear Parking
Assist (URPA)..................2-34
Uniform Tire Quality
Grading...........................5-52
Universal Home Remote
System...........................2-44
Operation........................2-45
V
Vehicle
Control............................. 4-3
Loading...........................4-16
Running While Parked.......2-31
Symbols.............................. iii
Vehicle Customization, DIC....3-57
Vehicle Data Recording and
Privacy............................7-14
Vehicle Identication
Number (VIN)...................5-90
Service Parts Identication
Label...........................5-91
Vehicle, Remote Start............. 2-5
Ventilation Adjustment...........3-25
Visors.................................2-16
Voltage Devices, High and
Wiring.............................5-91
Voltmeter Gage....................3-33
INDEX i-11