low beam BUICK LACROSSE 2007 Owner's Manual

Instrument Panel Overview........................ 148
Hazard Warning Flashers.......................... 150
Other Warning Devices............................. 150
Horn.......................................................... 150
Tilt Wheel.................................................. 151
Turn Signal/Multifunction Lever.................. 152
Turn and Lane-Change Signals................. 152
Headlamp High/Low-Beam Changer.......... 153
Flash-to-Pass............................................ 153
Windshield Wipers..................................... 153
Windshield Washer.................................... 154
Cruise Control........................................... 154
Exterior Lamps.......................................... 158
Daytime Running Lamps (DRL)/
Automatic Headlamp System.................. 159
Fog Lamps................................................ 160
Exterior Lighting Battery Saver.................. 160
Interior Lamps........................................... 161
Instrument Panel Brightness...................... 161
Courtesy Lamps........................................ 161
Entry Lighting............................................ 161
Delayed Entry Lighting.............................. 162
Theater Dimming....................................... 162
Delayed Exit Lighting................................. 162Perimeter Lighting..................................... 163
Overhead Console Reading Lamps........... 163
Rear Assist Handle Reading Lamps.......... 163
Electric Power Management...................... 163
Battery Run-Down Protection..................... 164
Ultrasonic Rear Parking Assist (URPA)...... 164
Accessory Power Outlet(s)........................ 167
Ashtray(s) and Cigarette Lighter................ 168
Climate Controls......................................... 168
Climate Control System............................. 168
Dual Automatic Climate Control System.... 172
Outlet Adjustment...................................... 177
Passenger Compartment Air Filter............. 178
Warning Lights, Gages, and Indicators..... 179
Instrument Panel Cluster........................... 180
Speedometer and Odometer...................... 181
Tachometer............................................... 181
Safety Belt Reminder Light........................ 181
Passenger Safety Belt Reminder Light....... 182
Airbag Readiness Light............................. 182
Passenger Airbag Status Indicator............. 183
Charging System Light.............................. 185
Brake System Warning Light..................... 186
Section 3 Instrument Panel
145

Anti-Lock Brake System Warning Light...... 187
Traction Control System (TCS)
Warning Light........................................ 187
Engine Coolant Temperature
Warning Light........................................ 188
Engine Coolant Temperature Gage............ 189
Low Coolant Warning Light....................... 189
Tire Pressure Light.................................... 190
Malfunction Indicator Lamp........................ 190
Oil Pressure Light..................................... 194
Change Engine Oil Light........................... 195
Security Light............................................ 195
Cruise Control Light.................................. 195
Reduced Engine Power Light.................... 196
Highbeam On Light................................... 196
Headlamps Suggested Light...................... 196
Low Washer Fluid Warning Light............... 197
Door Ajar Light.......................................... 197
Trunk Ajar Light........................................ 197
Service Vehicle Soon Light........................ 197
Fuel Gage................................................. 198
Low Fuel Warning Light............................ 198
Check Gas Cap Light................................ 199Driver Information Center (DIC)................... 199
DIC Operation and Displays...................... 200
DIC Compass (Uplevel Only)..................... 206
DIC Warnings and Messages.................... 208
DIC Vehicle Personalization....................... 229
Audio System(s)......................................... 238
Setting the Time........................................ 239
Radio with CD (Base)............................... 240
Radio with CD (Uplevel)............................ 245
Radio with CD (MP3)................................ 252
Radio with Six-Disc CD............................. 260
Using an MP3........................................... 272
XM Radio Messages................................. 278
Theft-Deterrent Feature............................. 280
Audio Steering Wheel Controls.................. 280
Radio Reception........................................ 281
Care of Your CDs..................................... 282
Care of the CD Player.............................. 282
Backglass Antenna.................................... 283
XM™ Satellite Radio Antenna System....... 284
Chime Level Adjustment............................ 284
Section 3 Instrument Panel
146

Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:
GTurn and Lane Change Signals. See
Turn and Lane-Change Signals on page 152.
2Headlamp High/Low-Beam Changer.
SeeHeadlamp High/Low-Beam Changer
on page 153.
Flash-to-Pass. SeeFlash-to-Pass on page 153.
NWindshield Wipers. SeeWindshield Wipers
on page 153.
LQWindshield Washer. SeeWindshield
Washer on page 154.
For information on the headlamps, seeExterior
Lamps on page 158.
Turn and Lane-Change Signals
To signal a turn, move the lever up or down.
The lever returns to its original position when the
turn is completed.
An arrow on the
instrument panel
cluster will ash in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until the
lane change is completed. The lever will return
to its original position when released.
Arrows that ash rapidly when signaling for a turn
or lane change, or that fail to work, may indicate
a burned-out signal bulb or fuse. Other drivers will
not see the signal. SeeFront Turn Signal and
Parking Lamps on page 397andTaillamps, Turn
Signal, Sidemarker, Stoplamps and Back-up
Lamps on page 398for turn signal bulb
replacement procedures. Also seeFuses and
Circuit Breakers on page 450for location of fuses.
A chime will sound if the turn signal is left on
for more than 3/4 mile (1.2 km).
152

Headlamp High/Low-Beam Changer
To change the headlamps from low beam to
high beam, push the turn signal/multifunction
lever away from you.
When the high beams
are on, a light on the
instrument panel cluster
also will be on if the
ignition is on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward you.
Flash-to-Pass
This feature lets you use your high-beam
headlamps momentarily to signal a driver in
front of you that you want to pass.
To use it, pull the turn signal/multifunction lever
toward you until the high-beam headlamps
come on, then release the lever to turn them off.
Windshield Wipers
Be sure to clear ice and snow from the wiper
blades before using them. If they are frozen to the
windshield, gently loosen or thaw them. Damaged
wiper blades may not clear the windshield well,
making it harder to see and drive safely. If the
blades do become damaged, install new blades or
blade inserts. For more information, seeWindshield
Wiper Blade Replacement on page 401.
Heavy snow or ice can overload the wiper motor. A
circuit breaker will stop the motor until it cools down.
Clear away snow or ice to prevent an overload.
You control the windshield wipers by turning the
band with the wiper symbol on it.
8(Mist):For a single wiping cycle, turn the
band to mist. Hold it there until the wipers
start. Then let go. The wipers will stop after
one wipe. If you want more wipe cycles, hold
the band on mist longer.
153

<(Parking Lamps):Turn the control to this
position to turn on the parking lamps together with
the following:
Taillamps
License Plate Lamps
Sidemarker Lamps
Instrument Panel Lights
2(Headlamps):Turn the control to this position
to turn your headlamps on, together with the
previously listed lamps and lights.
A warning chime will sound if the driver’s door is
opened when the ignition switch is turned to
OFF or ACCESSORY and the headlamps or
parking lamps are on.
-(Foglamps):If your vehicle has fog lamps,
press this button to turn them on and off. SeeFog
Lamps on page 160for additional information.
Daytime Running Lamps (DRL)/
Automatic Headlamp System
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. DRL lamps are required to function at
all times on all vehicles rst sold in Canada.
A light sensor on top of the instrument panel
makes the DRL work, so be sure it is not covered.
The DRL system will make the low-beam
headlamps come on at reduced brightness when
the following conditions are met:
The ignition is on.
The exterior lamps control is off.
The parking brake is released.
While the DRL are on, only the vehicle’s low-beam
headlamps will be on at reduced brightness.
The turn signal, taillamps, sidemarker, and other
lamps will not be on. The instrument panel will not
be lit up either.
159

When it is dark enough outside, the DRL will turn
off and the vehicle’s headlamps and parking
lamps will turn on. The other lamps that come on
with the headlamps will also come on.
When it is bright enough outside, the headlamps
will go off and the DRL will come on.
To idle the vehicle with the DRL off, turn the
exterior lamp control off and then do one of the
following:
Turn the exterior lamp control to the parking
lamp position.
Turn the exterior lamp control to the
headlamp position.
Turn the exterior lamp control from AUTO to
off and back to AUTO.
This feature is not available for vehicles rst sold
in Canada.
To turn off the automatic headlamp feature when it
is dark outside, move the exterior lamp control
to the parking lamp position. The parking lamps
remain on and the headlamps turn off. The
fog lamps also go on if they were on previously.
As with any vehicle, the regular headlamp system
should be turned on when needed.
Fog Lamps
If your vehicle has fog
lamps, the button is
located in the center of
the exterior lamps
control on the left side
of the steering column.
Press the fog lamps button to turn the lamps
on or off.
While the high-beam headlamps are on, the fog
lamps are off.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Exterior Lighting Battery Saver
If the parking lamps or headlamps have been left
on after the ignition has been turned to off, the
exterior lamps will turn off after about 10 minutes.
This protects the battery from being drained.
Use the exterior lamp control to turn the lamps
back on, if they are still needed.
160

A high electrical load occurs when several of the
following loads are on: headlamps, high beams,
fog lamps, rear window defogger, climate
control fan at high speed, heated seats, engine
cooling fans, trailer loads, and loads plugged into
accessory power outlets.
EPM works to prevent excessive discharge of the
battery. It does this by balancing the generator’s
output and the vehicle’s electrical needs. It
can increase engine idle speed to generate more
power, whenever needed. It can temporarily
reduce the power demands of some accessories.
Normally, these actions occur in steps or levels,
without being noticeable. In rare cases at the
highest levels of corrective action, this action may
be noticeable to the driver. If so, the Driver
Information Center (DIC) message might display
Battery Saver Active. If this message is displayed,
it is recommended that the driver reduce the
electrical loads as much as possible. See
DIC Warnings and Messages on page 208.Battery Run-Down Protection
This helps prevent the vehicle’s battery from
draining in case the interior courtesy lamps,
reading lamps, trunk lamp, underhood lamp, glove
box lamps, or sun visor vanity lamps, if equipped,
are accidently left on. If any of these lamps
are left on while the ignition is off, they will
automatically turn off after 10 minutes. The lamps
will not come back on again until one of the
following occurs:
The ignition is turned on.
The interior lamps control is turned off, then to
door or on.
Ultrasonic Rear Parking
Assist (URPA)
Your vehicle may be equipped with Ultrasonic Rear
Parking Assist (URPA). URPA is designed to help
you park while in REVERSE (R) and operates only
at speeds less than 3 mph (5 km/h). URPA can help
you avoid colliding with objects such as parked
vehicles. The system can detect objects 5 feet
(1.5 m) behind your vehicle and tell you how close
those objects are to your rear bumper.
164

Reduced Engine Power Light
If the reduced engine
power light is on, a
chime will sound and a
noticeable reduction
in the vehicle’s
performance may occur.
If the reduced engine power light is on, but there
is no reduction in performance, proceed to
your destination. The performance may be reduced
the next time the vehicle is driven. The vehicle
may be driven at a reduced speed while the
reduced engine power light is on, but acceleration
and speed may be reduced.
Anytime the reduced engine power light stays on,
the vehicle should be taken to an authorized
GM dealer as soon as possible for service.
Highbeam On Light
This light comes on
when the high-beam
headlamps are in use.
SeeHeadlamp High/Low-Beam Changer on
page 153.
Headlamps Suggested Light
This light will come on
when the use of
headlamps is
suggested.
196

No one can see as well at night as in the daytime.
But as we get older these differences increase.
A 50-year-old driver may require at least twice as
much light to see the same thing at night as a
20-year-old.
What you do in the daytime can also affect your
night vision. For example, if you spend the
day in bright sunshine you are wise to wear
sunglasses. Your eyes will have less trouble
adjusting to night. But if you are driving, do not
wear sunglasses at night. They may cut down on
glare from headlamps, but they also make a
lot of things invisible.
You can be temporarily blinded by approaching
headlamps. It can take a second or two, or
even several seconds, for your eyes to re-adjust
to the dark. When you are faced with severe glare,
as from a driver who does not lower the high
beams, or a vehicle with misaimed headlamps,
slow down a little. Avoid staring directly into
the approaching headlamps.Keep the windshield and all the glass on your
vehicle clean — inside and out. Glare at night is
made much worse by dirt on the glass. Even
the inside of the glass can build up a lm caused
by dust. Dirty glass makes lights dazzle and
ash more than clean glass would, making the
pupils of your eyes contract repeatedly.
Remember that the headlamps light up far less of a
roadway when you are in a turn or curve. Keep your
eyes moving; that way, it is easier to pick out dimly
lighted objects. Just as the headlamps should be
checked regularly for proper aim, so should your
eyes be examined regularly. Some drivers suffer
from night blindness — the inability to see in dim
light — and are not even aware of it.
304

To disconnect the jumper cables from both
vehicles, do the following:
1. Disconnect the black negative (−) cable from
the vehicle that had the dead battery.
2. Disconnect the black negative (−) cable from
the vehicle with the good battery.
3. Disconnect the red positive (+) cable from the
vehicle with the good battery.
4. Disconnect the red positive (+) cable from the
other vehicle.
5. Return the fuse block cover to its original
position.
Headlamp Aiming
The vehicle has a visual optical headlamp aiming
system. The aim has been preset at the factory
and should need no further adjustment
However, If the vehicle is damaged in an accident,
the headlamp aim may be affected and adjustment
may be necessary.
If oncoming vehicles ash their high beams at
you, this may also mean the vertical aim needs to
be adjusted.It is recommended that the vehicle is taken to your
dealer for service if the headlamps need to be
re-aimed. It is possible however, to re-aim
the headlamps as described in the following
procedure.
The vehicle should be properly prepared as follows:
The vehicle should be placed so the headlamps
are 25 ft. (7.6 m) from a light colored wall.
The vehicle must have all four tires on a
perfectly level surface which is level all the way
to the wall.
The vehicle should be placed so it is
perpendicular to the wall.
The vehicle should not have any snow, ice or
mud on it.
The vehicle should be fully assembled and all
other work stopped while headlamp aiming is
being done.
The vehicle should be normally loaded with a
full tank of fuel and one person or 160 lbs
(75 kg) on the driver’s seat.
Tires should be properly inated.
391