ECO mode BUICK LACROSSE 2009 User Guide

DIC Warnings and Messages
Messages are displayed on the uplevel DIC to notify the
driver that the status of the vehicle has changed and that
some action may be needed by the driver to correct the
condition. Multiple messages may appear one after
another.
Some messages may not require immediate action,
but you can press any of the uplevel DIC buttons to
acknowledge that you received the message and
clear it from the DIC display.
Some messages cannot be cleared from the DIC
display because they are more urgent. These messages
require action before they can be cleared.
If there are any active warning messages when the
vehicle is turned off, two chimes sound and the DIC goes
into a reminder mode. The reminder mode displays any
active message. If there are multiple messages, the DIC
displays each message for ve seconds. After each
active message is displayed once, the reminder mode
turns off.
You should take any messages that appear on the
display seriously and remember that clearing the
messages will only make the messages disappear,
not correct the problem.
The following are the possible messages that can be
displayed and some information about them.
A/C OFF FOR ENGINE PROTECTION
This message displays when the engine coolant
becomes hotter than the normal operating temperature.
SeeEngine Coolant Temperature Gage on page 3-38.
To avoid added strain on a hot engine, the air
conditioning compressor is automatically turned off.
When the coolant temperature returns to normal, the
air conditioning compressor turns back on. You can
continue to drive your vehicle.
This message comes on while the ignition is in ON/RUN.
Press any of the DIC buttons to acknowledge this
warning message and to clear it from the screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine
is turned off. It also re-displays for two seconds if the
message has been acknowledged, but the condition
still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on. If this message continues
to appear, have the system repaired by your dealer/
retailer as soon as possible to avoid damage to the
engine.
3-56

REDUCED ENGINE POWER
This message displays when the vehicle’s engine
power is reduced. Reduced engine power can affect the
vehicle’s ability to accelerate. If this message is on, but
there is no reduction in performance, proceed to your
destination. The performance may be reduced the next
time the vehicle is driven. The vehicle may be driven at a
reduced speed while this message is on, but acceleration
and speed may be reduced. Anytime this message stays
on, the vehicle should be taken to your dealer/retailer for
service as soon as possible.
This message displays and a chime sounds only when
the ignition is in ON/RUN. Press any of the DIC buttons
to acknowledge this message and to clear it from the
screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine
is turned off. It also re-displays for two seconds if the
message has been acknowledged, but the condition
still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
REDUCED POWER STOP WHEN SAFE
This message displays when your vehicle is in an
overheated engine operating mode. This operating mode
allows your vehicle to be driven to a safe place in an
emergency. In this mode, you will notice a signicant
loss in power and engine performance. SeeOverheated
Engine Protection Operating Mode on page 5-34for more
information. Anytime this message is on, the vehicle
should be taken to your dealer/retailer for service as
soon as possible.
This message displays and a chime sounds only when
the ignition is in ON/RUN. Press any of the DIC buttons
to acknowledge this message and to clear it from the
screen.
This message continues to display for two seconds
if it has not been acknowledged when the engine
is turned off. It also re-displays for two seconds if the
message has been acknowledged, but the condition
still exists when the engine is turned off.
If the condition still exists, the message re-appears
when the engine is turned on.
3-66

Playing the Radio
P
(Power):Press to turn the system on and off.
v(Volume):Turn to increase or to decrease the
volume.
DISP (Display):Press to switch the display between
the radio station frequency and time of day. While
the ignition is off, press this button to display the time.
If the vehicle’s radio has XM™, press the DISP
button while in XM mode to retrieve four different
categories of information related to the current song
or channel: Artist, Song Title, Category or PTY,
Channel Number/Channel Name.
To change the default on the display, press the DISP
button until the desired display appears, then hold DISP
for two seconds. The radio beeps once and the selected
display becomes the default.SCV (Speed Compensated Volume):If the vehicle’s
radio has Speed Compensated Volume (SCV), the audio
system adjusts automatically to make up for road and
wind noise while driving.
Set the volume at the desired level. Press this button
to select LOW, MEDIUM, or HIGH. Depending on the
radio, the selection may be SPEED VOL MIN (volume
minimum), SPEED VOL MED (volume medium), or
SPEED VOL MAX (volume maximum). Each higher
setting allows for more volume compensation at faster
vehicle speeds. Then while driving, SCV increases the
volume, as necessary, to overcome noise at any speed.
The volume level should always sound the same while
driving. NONE displays if the radio cannot determine the
vehicle speed. To turn SCV off, press SCV until OFF or
SPEED VOL OFF displays.
3-84

Scanning Categories (CAT)
(XM Satellite Radio Service Only)
To scan a desired category:
1. Press the CAT button to enter the category select
mode. The current category displays.
2. Turn the
eknob to select a category.
3. Press either SEEK arrow for two seconds once the
desired category is displayed, to scan the stations
in that category.
4. Press either SEEK arrow again to stop scanning.
If the radio cannot nd the desired category, NOT
FOUND displays and the radio returns to the last
station that was being listened to.
Radio Messages
CALIBRATE:The audio system has been calibrated
for the vehicle from the factory. If CALIBRATE displays, it
means that the radio has not been congured properly for
the vehicle and it must be returned to your dealer/retailer
for service.LOCKED:If LOCKED displays, it means the
THEFTLOCK
®system has locked up. Take the
vehicle to your dealer/retailer for service.
If any error occurs repeatedly or if an error cannot be
corrected, contact your dealer/retailer.
XM Satellite Radio Service
XM is a satellite radio service that is based in the
48 contiguous United States and 10 Canadian provinces.
XM Satellite Radio has a wide variety of programming
and commercial-free music, coast-to-coast, and in
digital-quality sound. During your trial or when you
subscribe, you will get unlimited access to XM Radio
Online for when you are not in the vehicle. A service
fee is required to receive the XM service. For more
information, contact XM at xmradio.com or call
1-800-929-2100 in the U.S. and xmradio.ca or
call 1-877-438-9677 in Canada.
Radio Messages for XM Only
SeeXM Radio Messages on page 3-98later in this
section for further detail.
3-88

BAND:Press to listen to the radio while a CD is
playing. The inactive CD remains inside the radio for
future listening.
CD:Press to play a CD while listening to the radio.
The CD symbol displays when a CD is loaded.
EQ (Equalization):Press to select an equalization
setting while playing a CD. The equalization is set while
a CD is played. See “EQ” listed previously for more
information. If an EQ setting is selected for a CD,
it is activated each time a CD is played.
Z(Eject):Press to eject a CD. Eject is activated
while either the ignition or radio is off. CDs can
be loaded while the ignition and radio is off if this
button is pressed rst.
Playing an MP3 CD-R Disc
The vehicle’s radio may have the MP3 CD-R disc
capability feature. For more information, seeUsing
an MP3 on page 3-95later in this section.
Using List Mode
The Six-Disc CD player has a feature called song list.
This feature is capable of saving 20 track selections.
To save tracks into the song list feature:
1. Turn the CD player on and load it with at least one
CD. See “LOAD” listed previously in this section for
more information.
2. Check to see that the CD player is not in song list
mode. LIST should not display. If LIST is displayed,
press the LIST button to turn it off.
3. Select the desired CD by pressing the numbered
pushbutton and then use the
parrow to locate
the track to be saved. The track begins to play.
4. Press and hold the LIST button to save the track
into memory. When LIST is pressed, one beep
sounds immediately. After two seconds of
continuously pressing the LIST button, TRACK
ADD displays and two beeps sound to conrm the
track has been saved.
5. Repeat Steps 3 and 4 for saving other selections.
S-LIST FULL displays if more than 20 selections
are saved.
3-92

To play the song list, press the LIST button. One beep
sounds and S-LIST displays. The recorded tracks
begins to play in the order they were saved.
Seek through the song list by using the SEEK arrows.
Seeking past the last saved track returns to the rst
saved track.
To delete tracks from the song list:
1. Turn the CD player on.
2. Press the LIST button to turn song list on.
LIST displays.
3. Press either SEEK arrow to select the desired track
to be deleted.
4. Press and hold the LIST button for two seconds.
When LIST is pressed, one beep sounds
immediately. After two seconds of continuously
pressing the LIST button, TRACK DELETE displays
and the radio beeps twice to conrm that the track
has been deleted.After a track has been deleted, the remaining tracks
are moved up the list. When another track is added to
the song list, the track is added to the end of the list.
To delete the entire song list:
1. Turn the CD player on.
2. Press the LIST button to turn song list on.
LIST displays.
3. Press and hold the LIST button for more than
four seconds. The radio beeps once, followed
by two beeps after two seconds, and a nal beep
sounds after four seconds. LIST EMPTY displays
indicating the song list has been deleted.
If a CD is ejected, and the song list contains saved
tracks from that CD, those tracks are automatically
deleted from the song list. Any tracks saved to the
song list again are added to the bottom of the list.
To end song list mode, press the LIST button. The radio
beeps once and LIST is removed from the display.
3-93

The player is able to read and play a maximum of
50 folders, 50 playlists, 10 sessions, and 255 les.
Long le names, folder names, or playlist names could
use more disc memory space than necessary. To
conserve disc space, keep the length of the le, folder, or
playlist name brief. MP3 CDs do not require le folders.
The system can support up to 11 folders in depth. The
depth of the folders should be kept down to make it easier
while locating a folder during playback. All items over the
maximum are ignored.
Root Directory
The root directory is treated as a folder. If the root
directory has compressed audio les, the directory
displays as F1 ROOT. All les contained directly under
the root directory are accessed prior to any root directory
folders. However, playlists (Px) always are accessed
before root folders or les.
Empty Directory or Folder
If a root directory or a folder exists somewhere in the
le structure that contains only folders/subfolders and
no compressed les directly beneath them, the player
advances to the next folder in the le structure that
contains compressed audio les and the empty folder
does not display.
No Folder
If a CD has no folder, only compressed les or playlists
are located under the root folder. The next and
previous folder functions have no function on a CD that
is recorded without folders or playlists. When displaying
the name of the folder the radio displays ROOT.
Order of Play
Tracks are played in the following order:
Play begins from the rst track in the rst playlist
and continues sequentially through all tracks in
each playlist. When the last track of the last playlist
has played, play continues from the rst track of
the rst playlist.
If the CD does not contain any playlists, then play
begins from the rst track under the root directory.
When all tracks from the root directory have played,
play continues from les according to their numerical
listing. After playing the last track from the last folder,
play begins again at the rst track of the rst folder or
root directory.
When play enters a new folder, the display does
not automatically show the new folder name unless
the folder mode is chosen as the default display.
See “DISP” later in this section for more information.
The new track name displays.
3-96

DISP (Display):Press to change between track mode,
folder/playlist mode, and ID3 tag. The display shows
only eight characters, but there can be up to four pages
of text. If there are more than eight characters in the
song, folder, or playlist name, pressing this knob within
two seconds goes to the next page of text. If there
are no other pages to be shown, pressing this button
within two seconds goes to the next display mode.
Song name and time of day mode displays
the current song name and time of day.
Folder/playlist mode displays the current folder or
playlist number the track number and the elapsed
time of the track.
Song name and track number mode displays the
current song name and track number.
ID3 Tag and folder mode displays the ID3 tag
information and the folder number.
Song and folder mode displays the number of
songs in the folder and the folder number.
INFO (Information):INFO displays when a current
track has ID3 tag information. Press this button to
display the artist name and album contained in the tag.
BAND:Press to listen to the radio when a CD is
playing. The inactive CD remains inside the radio
for future listening.
XM Radio Messages
XL (Explicit Language Channels):These
channels, or any others, can be blocked by
calling 1-800-852-XMXM (9696).
Updating:The encryption code in the receiver is being
updated, and no action is required. This process should
take no longer than 30 seconds.
No Signal:The system is functioning correctly, but the
vehicle is in a location that is blocking the XM signal.
When the vehicle is moved into an open area, the signal
should return.
Loading XM:The audio system is acquiring and
processing audio and text data. No action is needed.
This message should disappear shortly.
CH Off Air:This channel is not currently in service.
Tune in to another channel.
CH Unauth:This channel is blocked or cannot be
received with your XM Subscription package.
CH Unavail:This previously assigned channel is no
longer assigned. Tune to another station. If this station
was one of the presets, choose another station for
that preset button.
3-98

How to Reset the Engine Oil Life
System
The Engine Oil Life System calculates when to change
the engine oil and lter based on vehicle use. Whenever
the oil is changed, reset the system so it can calculate
when the next oil change is required. If a situation occurs
where the oil is changed prior to a change engine oil light
or CHANGE OIL SOON message being turned on, reset
the system.
After changing the engine oil, reset the system:
Vehicles with Driver Information Center (DIC)
1. Press the option button on the DIC until
ENGINE OIL MONITOR appears on the
DIC screen.
2. Press the set/reset button to reset the system.
The next screen indicates that the CHANGE
OIL SOON message has been reset.
If the vehicle has the uplevel DIC, when the
gages button is pressed and the OIL LIFE
REMAINING mode appears, it should read
100 percent OIL LIFE REMAINING.
3. Turn the key to LOCK/OFF.
Vehicles without Driver Information Center (DIC)
1. With the engine off, turn the ignition key to
ON/RUN.
2. Fully press and release the accelerator pedal
slowly three times within ve seconds.
3. Turn the key to LOCK/OFF, then start the
vehicle.
If the light or message comes back on when the vehicle
is started, the oil life system has not reset. Repeat
the procedure.
What to Do with Used Oil
Used engine oil contains certain elements that can be
unhealthy for your skin and could even cause cancer.
Do not let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good hand
cleaner. Wash or properly dispose of clothing or rags
containing used engine oil. See the manufacturer’s
warnings about the use and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil from the
lter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or into
streams or bodies of water. Recycle it by taking it to a
place that collects used oil.
5-19

Intended Outboard Sidewall:The side of an
asymmetrical tire, that must always face outward
when mounted on a vehicle.
Kilopascal (kPa)
:The metric unit for air pressure.
Light Truck (LT-Metric) Tire
:A tire used on
light duty trucks and some multipurpose passenger
vehicles.
Load Index
:An assigned number ranging from
1 to 279 that corresponds to the load carrying
capacity of a tire.
Maximum Ination Pressure
:The maximum
air pressure to which a cold tire can be inated.
The maximum air pressure is molded onto the
sidewall.
Maximum Load Rating
:The load rating for a tire
at the maximum permissible ination pressure
for that tire.
Maximum Loaded Vehicle Weight
:The sum of
curb weight, accessory weight, vehicle capacity
weight, and production options weight.Normal Occupant Weight
:The number of
occupants a vehicle is designed to seat multiplied
by 150 lbs (68 kg). SeeLoading the Vehicle on
page 4-20.
Occupant Distribution
:Designated seating
positions.
Outward Facing Sidewall
:The side of an
asymmetrical tire that has a particular side that
faces outward when mounted on a vehicle.
The side of the tire that contains a whitewall,
bears white lettering, or bears manufacturer,
brand, and/or model name molding that is higher
or deeper than the same moldings on the other
sidewall of the tire.
Passenger (P-Metric) Tire
:A tire used on
passenger cars and some light duty trucks and
multipurpose vehicles.
Recommended Ination Pressure
:Vehicle
manufacturer’s recommended tire ination
pressure as shown on the tire placard.
SeeInflation - Tire Pressure on page 5-61
andLoading the Vehicle on page 4-20.
5-59