tow BUICK LESABRE 1999 Owner's Guide

yellowblue
2-61 Voltage Gage (If Equipped)
If your vehicle is equipped
with the gage cluster, this
gage shows voltage in the
electrical system.
The normal range is 11 to 15 volts. If the gage reading
stays in either red range, or the battery warning light
turns on, have your dealer check the electrical system.
Brake System Warning Light
Your vehicle's hydraulic brake system is divided into
two parts. If one part isn't working, the other part can
still work and stop you. For good braking, though, you
need both parts working well.If the warning light comes on, there is a brake problem.
Have your brake system inspected right away.
Standard Cluster Gage Cluster
One of these lights should come on when you turn the
key to START. If it doesn't come on then, have it fixed
so it will be ready to warn you if there's a problem.
If the light and chime come on while you are driving,
pull off the road and stop carefully. You may notice that
the pedal is harder to push. Or, the pedal may go closer
to the floor. It may take longer to stop. If the light is still
on, have the vehicle towed for service. (See ªTowing
Your Vehicleº in the Index.)

yellowblue
2-62
CAUTION:
Your brake system may not be working properly
if the brake system warning light is on. Driving
with the brake system warning light on can lead
to an accident. If the light is still on after you've
pulled off the road and stopped carefully, have
the vehicle towed for service.
When the ignition is on, the brake system warning light
will also come on when you set your parking brake.
The light will stay on if your parking brake doesn't
release fully. If you try to drive off with the parking
brake set, a chime will also come on until you release
the parking brake. If the light and chime stay on after
your parking brake is fully released, it means you have
a brake problem.
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when you start
your engine and may stay
on for several seconds.
That's normal.
If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.

yellowblue
2-66
This light should come on, as a check to show you it is
working, when the ignition is on and the engine is not
running. If the light doesn't come on, have it repaired.
This light will also come on during a malfunction in one
of two ways:

Light Flashing
-- A misfire condition has been
detected. A misfire increases vehicle emissions and
may damage the emission control system on your
vehicle. Dealer or qualified service center diagnosis
and service may be required.

Light On Steady
-- An emission control system
malfunction has been detected on your vehicle.
Dealer or qualified service center diagnosis and
service may be required.
If the Light Is Flashing
The following may prevent more serious damage to
your vehicle:

Reducing vehicle speed.

Avoiding hard accelerations.

Avoiding steep uphill grades.

If you are towing a trailer, reduce the amount of
cargo being hauled as soon as it is possible.If the light stops flashing and remains on steady, see ªIf
the Light Is On Steadyº following.
If the light continues to flash, when it is safe to do so,
stop the vehicle. Find a safe place to park your vehicle.
Turn the key off, wait at least 10 seconds and restart the
engine. If the light remains on steady, see ªIf the Light
Is On Steadyº following. If the light is still flashing,
follow the previous steps, and drive the vehicle to your
dealer or qualified service center for service.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully install
the cap. See ªFilling Your Tankº in the Index. The
diagnostic system can determine if the fuel cap has been
left off or improperly installed. A loose or missing fuel
cap will allow fuel to evaporate into the atmosphere. A
few driving trips with the cap properly installed should
turn the light off.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-3
VENT: This setting directs outside air through the
middle instrument panel outlets. The air conditioning
compressor is not working when VENT is selected.
HTR: This button directs air out of the heater outlets.
Most of the air will come from the floor outlets while
some air will flow through the windshield and side
window outlets. The air conditioning compressor is not
working when HTR is selected.
BLEND: When BLEND is selected, the airflow will be
split between the windshield and the floor outlets. The
air conditioning compressor will be operating.
FRONT: This setting directs most of the airflow toward
the windshield.
OFF: The ventilation system always allows fresh air to
flow through your vehicle when it is moving. The
system will try to keep the air at a previously chosen
temperature. When the system is off, the blower fan is
also off.
MAX: This setting directs airflow through the middle
instrument panel outlets. The amount of outside air
entering your vehicle is limited with this setting. The air
conditioning compressor is on in this mode.NORM: This setting cools the outside air entering your
vehicle and directs it through the middle instrument
panel outlets. The air conditioner is on in this mode.
BI
-LEV: This setting directs warm air to the floor and
cooler air to the middle instrument panel outlets. The air
conditioner is on in this mode.
Dual Automatic Comfortemp
Climate Control (If Equipped)
If your vehicle has the Dual Automatic Comfortemp
Climate Control option, the following information tells
you how it works.
You will hear a beep each time a button is pushed and a
light on the button will indicate which function is active.
The lights are on all buttons except TEMP, FAN and
AIR FLOW. The display will show fan speed, comfort
level setting and airflow direction for a few seconds
whenever AUTO is selected, and then it will display the
outside temperature. The outside temperature reading is
most accurate when the vehicle is moving. During stops,
the display shows the previous temperature for best
accuracy and system control.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-4
C±43±2053±T
If the display is flashing after the climate control system
is started, there is a problem with the system and you
should see your dealer for service.
Sun and temperature sensors automatically adjust the air
temperature, the airflow direction and the fan speed to
maintain your comfort setting. The system may supply
cooler air to the side of the vehicle toward the sun. Be
careful not to put anything over the sensors on top of
the dash.Temperature Button
To adjust the comfort level you want maintained inside
the vehicle, push the TEMP button. If you want a
warmer comfort level, push the red arrow. If you want a
cooler comfort level, push the blue arrow. Your comfort
setting is shown in the display.
Fan Button
The speed of the blower fan is controlled automatically if
you have the system set for AUTO. Pressing the FAN
button will display and hold the current blower fan setting.
If you want the blower fan to run at a lower speed, push
the bottom of the FAN button. The fan speed will
decrease with every push of the button until the lowest
speed is reached. If you want to increase the fan speed,
push the top of the FAN button. Notice the fan
indicators in the display.
Mode Controls
Press the AIR FLOW button to deliver air through the
floor, middle or windshield outlets. The system will stay
in the selected mode until the AUTO button is pushed.
Use the up and down arrows on the AIR FLOW button
to cycle through the available modes.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-5
Automatic Operation
Press the AUTO button when you want the system to
automatically adjust to changes in the temperature inside
the vehicle, the outside temperature and the sun load on
the vehicle. When the system is set for automatic
operation, air will come from the floor, middle or
windshield outlets depending on the temperature inside
the vehicle, the outside temperature and sun load. Fan
speed will vary as the system gets to and maintains the
comfort setting you have selected through the use of the
TEMP button.
To find your comfort setting, start with the system in
AUTO mode and the TEMP button adjusted to 75
F
(24
C), give the vehicle about 20 minutes to stabilize,
and adjust your comfort setting if necessary, by using
the TEMP button. The display will show the comfort
setting for a few seconds and then it will display the
outside temperature. If you want to see your current
automatic fan speed, airflow direction and comfort
setting, press the AUTO button.
In cold weather, the system will delay turning on the
fan, to avoid blowing cold air. The length of the delay
depends on the engine coolant temperature and the
outside temperature. Pushing the FAN, AIR FLOW or
FRONT buttons will override this delay, turn off the
AUTO setting and change the fan speed.Manual Operation
You may also manually adjust the air delivery or
fan speed.
AIR FLOW: This button is used to change the direction
of the airflow. The airflow choices available are FLOOR,
FLOOR
-MID, MID and WINDSHIELD-FLOOR. If the
system is set for AUTO, pressing the AIR FLOW button
will display the current airflow direction and the comfort
setting. Press the AIR FLOW up or down button again to
change the direction of the airflow.
If the AIR FLOW up button is selected while in the
FRONT defrost mode, the system will direct the air
toward the windshield and the floor. If the AIR FLOW
down button is selected while in the FRONT defrost
mode, the system will direct the air toward the floor, and
the FRONT defrost mode will cancel. Notice the arrows
in the display.
OFF: If the passenger comfort control is turned on, it can be
turned off by pressing the OFF button once. Pressing the OFF
button a second time will turn off the main system. Turning
off the main system causes the fan to turn off and the airflow
to be directed toward the floor. The system will still try to
keep the interior of the vehicle at the previous chosen
comfort setting. The outside temperature will show on the
display when the system is OFF.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-6
The ventilation system always allows fresh air to flow
through your vehicle when the vehicle is moving even
with the system in the OFF mode.
VENT: The VENT button allows outside air to flow
through your vehicle without the air conditioning
compressor working. Selecting VENT and the AUTO
button at the same time allows the system to control
automatically without the use of the air conditioning
compressor or the use of the RECIRC mode. To turn off
the VENT selection, push the VENT button again.
RECIRC: When RECIRC is selected, the system will
limit the amount of outside air entering your vehicle. This
is helpful when you are trying to cool the interior of the
vehicle quickly or limit the amount of outside air entering
your vehicle. RECIRC and AUTO may be selected at the
same time. The system will remain in RECIRC until the
ignition is turned off, then the system will return back to
the previously selected mode. Deselecting the RECIRC
button will also turn off the RECIRC function. RECIRC
can be selected in all manual airflow modes except
FRONT defrost and VENT.
FRONT: This selection is used to defrost the windshield
by directing the airflow toward the windshield.If FRONT is selected while in the AUTO mode, the fan
speed and the air temperature from the front defroster will
vary. If a manual fan speed setting is selected, the fan
speed will remain at that selection until another fan speed
selection is made or the AUTO mode is selected. To turn
off FRONT, press the AUTO or AIR FLOW button.
FRONT defrost will work better if any ice or snow is
cleared from the hood and the air inlet area between the
base of the windshield and the hood.
Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner to work its best.
If you have the electronic touch system, for quick
cool
-down on very hot days, use MAX with the
temperature and fan speed adjusted to COOL and
HIGH. If this setting is used for long periods of time, the
air in your vehicle may become too cold and dry.
For normal cooling on hot days, use NORM and adjust
the temperature and fan speed for your comfort. If
RECIRC is selected while in the NORM air
conditioning mode, the system works like MAX and
recirculates the air.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-7
On sunny days, when the air is moderately warm or
cool, use BI
-LEV to deliver warm air to the floor and
cooler air to the middle instrument panel outlets. On
days like these, the sun may adequately warm your
upper body, but your lower body may not be warm
enough. To warm or cool the air delivered, adjust the
TEMPERATURE lever.
The amount of fresh air entering the vehicle is limited
when RECIRC is selected. This is helpful when you are
trying to cool the air in your vehicle or limit the air
entering the vehicle.
If your vehicle has the Dual Automatic Comfortemp
system and it is set for AUTO, on very hot days, the
system will automatically enter the RECIRC mode and
the temperature door will be positioned at the full cold
position for maximum cooling. If the system is not in
the AUTO mode, RECIRC should be selected to provide
maximum cooling. You can choose the extreme comfort
setting of 60
F (16
C), but the system will not cool any
faster by choosing the extreme comfort setting.
When the air conditioner is on, you may sometimes
notice slight changes in your vehicle's engine speed and
power. This is normal because the system is designed to
cycle the compressor on and off to keep the
desired temperature.Heating
If your vehicle has the electronic touch system, on
cold days, use HTR with the TEMPERATURE lever
toward WARM.
If your vehicle has the Dual Automatic Comfortemp
system, and on cold days, if the AUTO mode is selected,
the system will automatically direct the air toward the
floor and the temperature door will be positioned at the
full hot position. You can choose the extreme comfort
setting of 90
F (32
C) but the system will not warm up
any faster by selecting the extreme comfort setting. If
the outside temperature is cold, the fan will be delayed
to avoid blowing cold air. Pushing the FAN, AIR FLOW
or FRONT buttons will override this delay, turn off the
AUTO mode and change the fan speed.
With each system, outside air will be brought in and sent
through the floor outlets. The heater works best if you
keep your windows closed while using it.

First Edition for Buick LeSabre Owner's Manual ± 1999
yellowblue
3-8 Defogging and Defrosting
If you have the electronic touch system, adjust the
TEMPERATURE lever toward WARM and the FAN
lever toward HIGH.
If you have the Dual Automatic Comfortemp system,
use the FRONT button to defog or defrost the
windshield. By choosing this button, the airflow will be
directed at the windshield. Adjust your comfort level by
pressing the TEMP up or down arrow. The fan speed
will be controlled by the system. You can change the fan
speed by pressing the top of the FAN button to increase
speed, and the bottom of the button to decrease speed.
To reduce the chance of fogging your windows in cold
weather, using the electronic touch system, select HTR
to supply air through the floor outlets. Then move the
FAN lever to HIGH for a few moments before driving
away. This will blow moist air from the intake outlets
toward the floor, not the windshield. If you have the
Dual Automatic Comfortemp system, the AUTO setting
will do this for you. Manual operation of the automatic
comfortemp system in the FLOOR mode will also
supply air through the floor outlets.
Rear Window Defogger
C±43±0375±S
The lines you see on the
rear window warm the
glass. Press this button to
start warming your window.
After 10 minutes it will turn off by itself, or pressing the
button during the heating cycle will turn it off. If you
need additional warming time, push the button again.
The system will then operate for five minutes before
going off by itself.

4-
yellowblue
4-1
Section 4 Your Driving and the Road
Here you'll find information about driving on different kinds of roads and in varying weather conditions. We've also
included many other useful tips on driving.
4
-2 Defensive Driving
4
-3 Drunken Driving
4
-6 Control of a Vehicle
4
-6 Braking
4
-10 Steering
4
-12 Off-Road Recovery
4
-13 Passing
4
-14 Loss of Control
4
-15 Driving at Night
4
-17 Driving in Rain and on Wet Roads4
-20 City Driving
4
-21 Freeway Driving
4
-22 Before Leaving on a Long Trip
4
-23 Highway Hypnosis
4
-23 Hill and Mountain Roads
4
-25 Winter Driving
4
-29 Recreational Vehicle Towing
4
-30 Loading Your Vehicle
4
-32 Towing a Trailer