BUICK RANDEZVOUS 2002 Owner's Manual

2-113
Interior Lighting On
The interior lighting on feature can be programmed to
one of the following modes:
KEY OUT: The interior lamps will come on for
about 25 seconds whenever you remove the key from
the ignition.
DOOR: The interior lamps will come on for about
25 seconds when any door is opened.
Interior lighting on will not occur while the ignition is in
ON. After 25 seconds have passed, the interior lamps
will slowly fade out. The lamps will fade out before the
25 seconds have passed if the following conditions
are met:

The ignition is turned to ON,

LOCK is pressed on the optional remote keyless
entry transmitter, or

there is no occupant activity detected for an
illumination period of 25 seconds.Before your vehicle was shipped from the factory, it was
programmed in DOOR. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until INTERIOR
LIGHTING ON appears on the DIC.
3. Press the SET button until the arrow is before KEY
OUT or DOOR.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-114
Auto Door Lock
The auto door lock feature can be programmed to one of
the following modes:
ON: The doors will automatically lock when shifted out
of PARK (P).
OFF: You will always need to lock your doors manually
before driving to increase occupant safety.
If programmed to ON, you may also program other
characteristics of the automatic door unlock feature.
See ªAutomatic Door Unlockº next in this section.
Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until AUTO DOOR LOCKS
appears on the DIC.3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.
Auto Door Unlock
If the auto door lock feature has been programmed to
ON, you can program your vehicle to one of the
following modes:
OFF: When the shift lever is put in PARK (P), your
doors will not unlock automatically.
DRIVER: When the shift lever is put in PARK (P), only
your driver's door will unlock.
ALL: When the shift lever is put in PARK (P), all doors
will unlock.

2-115
Before your vehicle was shipped from the factory, it was
programmed in ALL. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Make sure that the AUTO DOOR LOCK feature is
programmed to ON.
3. Press the MODE button until AUTO DOOR
UNLOCK appears on the DIC.
4. Press the SET button until the arrow is before OFF,
DRIVER or ALL.
If the auto door unlock feature has been programmed to
DRIVER or ALL, the automatic door unlock feature can
also be programmed to one of the following modes:
PARK: All doors will unlock when the shift lever is put
in PARK (P).
KEY OUT: All doors will unlock when the ignition key
is removed.Before your vehicle was shipped from the factory, it was
programmed in PARK. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming
AUTO DOOR UNLOCK to DRIVER or ALL
listed previously.
3. Press the MODE button until AUTO DOOR
UNLOCK/ PARK KEYOUT appears on the DIC.
4. Press the SET button until the arrow is before PARK
or KEY OUT.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-116
Delayed Locking
The delayed locking feature can be programmed to one
of the following modes:
ON: Lock your vehicle using the power door lock
switch or the optional remote keyless entry transmitter
while any door is opened, you will hear three chimes
and the doors will not lock. Five seconds after the last
door is closed, all doors will lock.
Once delayed locking is programmed to ON, you can do
the following:

Cancel the delayed locking by pressing unlock using
the power door lock switch or by fully inserting the
key in the ignition,

override the delayed locking feature by pressing lock
immediately using the power door lock switch, or

let the delayed locking feature complete the locking
of the vehicle.OFF: The doors will always lock immediately when
you lock the doors using the power door lock switch
or press LOCK on the optional remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in ON. The mode to which the vehicle has
been programmed may have been changed since it left
the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until DELAYED LOCKING
appears on the DIC.
3. Press the SET button until the arrow is before ON
or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-117
Remote Door Unlock
The remote door unlock feature can be programmed to
one of the following modes:
DRIVER/ALL: With the first press of UNLOCK on
the remote keyless entry transmitter, the driver's door
will unlock, and with the second press of UNLOCK,
within five seconds of the first press, all passenger's
doors will unlock.
ALL: All doors will unlock with every press of
UNLOCK on the remote keyless entry transmitter.Before your vehicle was shipped from the factory, it was
programmed in ALL. The mode to which the vehicle
has been programmed may have been changed since it
left the factory. To determine the mode to which your
vehicle is programmed or to program your vehicle to a
different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until REMOTE DOOR
UNLOCK appears on the DIC.
3. Press the SET button until the arrow is before
DRIVER/ALL or ALL.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-118
Unlock Feedback
The unlock feedback feature can be programmed to one
of the following modes:
LIGHTS: This mode does the following:

During the day, when the ignition is in OFF and
UNLOCK on the remote keyless entry transmitter
is pressed, the headlamps and parking lamps will
flash, or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to any
mode but OFF, the headlamps and parking lamps
will be activated for the same time period as the
headlamp exit delay feature is programmed to when
UNLOCK is pressed on the remote keyless entry
transmitter (see ªHeadlamp Exit Delayº earlier in
this section), or

during the night, when the ignition is in OFF and the
headlamp exit delay feature is programmed to OFF,
the headlamps and parking lamps will be activated
for 30 seconds when UNLOCK is pressed on the
remote keyless entry transmitter (see ªHeadlamp
Exit Delayº earlier in this section).OFF: The headlamps and parking lamps will not
flash when UNLOCK is pressed on the remote keyless
entry transmitter.
Before your vehicle was shipped from the factory, it was
programmed in LIGHTS. The mode to which the
vehicle has been programmed may have been changed
since it left the factory. To determine the mode to which
your vehicle is programmed or to program your vehicle
to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming
HEADLAMP EXIT DELAY earlier in this section,
to make sure which mode it is programmed to.
3. Press the SET button until UNLOCK FEEDBACK
appears on the DIC.
4. Press the MODE button until the arrow is before
LIGHTS or OFF.
5. Press the SET button once you have determined
which mode you prefer.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-119
Lock Feedback
The lock feedback feature can be programmed to one of
the following modes:
OFF: When LOCK is pressed on the remote keyless
entry transmitter, the headlamps and parking lamps will
not flash and the horn will not sound.
LIGHTS: When LOCK is pressed on the remote
keyless entry transmitter, the headlamps and parking
lamps will flash briefly.
LIGHTS and HORN: When LOCK is pressed a
second time on the remote keyless entry transmitter
within five seconds, the headlamps and parking lamps
will flash briefly and the horn will sound.Before your vehicle was shipped from the factory, it was
programmed in LIGHTS and HORN. The mode to
which the vehicle has been programmed may have been
changed since it left the factory. To determine the mode
to which your vehicle is programmed or to program
your vehicle to a different mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until LOCK FEEDBACK
appears on the DIC.
3. Press the SET button until the arrow is before OFF,
LIGHTS or LIGHTS and HORN.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-120
Seat Recall
The seat recall feature can be programmed to one of the
following modes:
ON: The previously programmed memory seat position
will be recalled when the UNLOCK button is pressed on
the remote keyless entry transmitter.
OFF: No memory seat position will be recalled when
you press the UNLOCK button on the remote keyless
entry transmitter.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until SEAT RECALL
appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.If the seat recall feature has been programmed to ON,
the seat recall feature can also be programmed to one of
the following modes:
MEMORY: The position recalled will be the memory
driving position.
EXIT: The position recalled will be the previously
programmed exit position.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Follow the instructions for programming SEAT
RECALL to ON listed previously.
3. Press the MODE button until RECALL POSITION
appears on the DIC.
4. Press the SET button until the arrow is before
MEMORY or EXIT.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.

2-121
Tilt Mirror
The tilt mirror feature can be programmed to one of the
following modes:
ON: The passengers side outside rearview mirror will
tilt down towards the curb when the vehicle is shifted to
REVERSE (R) and returns to its previous position when
the vehicle is shifted out of REVERSE (R).
OFF: The mirror will not tilt.
To determine the mode to which your vehicle is
programmed or to program your vehicle to a different
mode, do the following:
1. Follow the instructions for ªEntering Programming
Modeº listed previously.
2. Press the MODE button until TILT appears on
the DIC.
3. Press the SET button until the arrow is before
ON or OFF.
The mode you selected is now set. You can either exit
programming mode by following the instructions later in
this section or program the next feature available on
your vehicle.Exiting Programming Mode
To exit programming mode, do one of the following:

Shift out of PARK (P),

turn the ignition key out of ON, or

do not program any commands for one minute while
in the programming mode.
The programming mode message will turn off to let you
know that you are no longer in the programming mode.
Once you have reached the end of the personalization
features, PERSONALIZATION SELECTION DONE
will appear briefly. Then PRESS SET TO EXIT MODE
TO CONTINUE will appear. Pressing SET will exit you
out of the DIC. Pressing MODE will take you to the
beginning of personalization.

2-122
Head-Up Display (HUD) (Option)
CAUTION:
If the HUD image is too bright, or too high in
your field of view, it may take you more time to
see things you need to see when it's dark outside.
Be sure to keep the HUD image dim and placed
low in your field of view.
If your vehicle has this option, it can display the
speedometer reading in English or metric. The current
radio station, CD number and/or track number or tape
may also be displayed and will appear as an image
focused out toward the front of your vehicle.
The HUD is capable of displaying English or French.
See ªDriver Information Center (DIC) Messagesº
earlier in this section to change the display from English
to metric.The Head
-Up Display also displays the following lights
and messages when they appear on the instrument
panel cluster:

Turn Signal Indicators

High
-Beam Indicator

Low
-Fuel Warning Message
See each of these features in the Index for
more information.
The Head
-Up Display also displays a CHECK GAGES
icon. The following messages could appear on the
instrument panel cluster when CHECK GAGES appears:

Engine Coolant Temperature Warning Message

Low Oil Pressure Message

Charging System Indicator Message

Low Brake Fluid Warning Message
See each of these messages in the Index for
more information.