buttons BUICK RANDEZVOUS 2002 Owner's Manual

1-5
You can also store an exit position for each driver.
The exit position is programmed by moving the seat
to the desired exit position and then holding the exit
symbol button for more than three seconds. The exit
position set will be for the most recently selected driving
position (1 or 2). A double beep will sound when the
memory is set.
To use exit, your vehicle must be in PARK (P). Push
and release the exit symbol button and the seat will
move to the exit position stored for the most recently
selected driver. You will hear one beep.
To stop recall movement of the seat at any time,
press one of the three memory buttons or one of the
power seat controls located on the outboard side of
the driver's seat.
If your vehicle is equipped with a Driver Information
Center (DIC), you can use it to program certain
functions of the memory seats. See ªDriver Information
Center (DIC) Vehicle Customizationº in the Index.Heated Front Seats (Option)
The heated seat switches
are located in the center
console switchbank.
This feature will quickly heat the lower cushions and
lower back of the driver's and front passenger's seat for
added comfort. The left switch is for the driver's seat
and the right switch is for the front passenger's seat.
Press the top of the switch to turn the heater on.
Press the bottom of the switch to turn the heater off.
The heated seat switch will turn off when the ignition
is turned to OFF and will resume operation when the
ignition is turned to ON, unless the switch is manually
turned off.

2-57 Electrochromic Automatic Dimming
Rearview Mirror (If Equipped)
Your vehicle may have an electrochromic day/night
rearview mirror. Push the button in the center of the
mirror to turn this feature on. The mirror will darken
gradually to reduce glare from headlamps behind you.
This may take a few moments. The mirror will also
lighten whenever you shift to REVERSE (R).
The mirror's two outer buttons operate the lights on the
bottom sides of the mirror.
One photocell on the front of the mirror senses when it
is becoming dark outside. Another photocell, facing
rearward, senses headlamps behind you.To turn the electrochromic feature off, press the button
in the center of the mirror again.
To keep the photocells operating well, occasionally
clean them with a cotton swab and glass cleaner.
Power Outside Rearview Mirrors
The power mirror
controls are located
on the driver's
door armrest.
To choose either the left or right outside mirror,
press the selector switch. Press any of the four arrows
located on the control pad to move the mirrors in the
desired direction.
Adjust each mirror so you can see the side of your
vehicle and the area behind your vehicle.

2-59
Storage Compartments
There are four small storage compartments in the rear of
your vehicle. One is on the passenger's side, two are on
the driver's side and one is on the floor by the tailgate.
To remove the covers, lift up on the tabs and remove. If
equipped with the 10
-speaker system, the compartment
on the passenger's side and the long compartment on the
driver's side will be equipped with speakers.
Glove Box
To unlock the glove box, put your key into the lock and
turn the key counterclockwise. To open the glovebox,
pull the latch release.
The glove box door has a detent to prevent the door
from lowering too far. Open the glove box until the door
is partway open, then pull the door down if you need it
fully opened.
To close the glove box, the door must be pushed up past
the detent. To lock the glovebox, put your key into the
lock and turn the key clockwise.
Overhead Consoles (If Equipped)
If your vehicle has
an overhead console
it may contain a storage
compartment, a
compartment for your
garage door opener
and a compartment
for your sunglasses.
If your vehicle has the optional OnStar System, the
OnStar buttons will be located at the front of the console
and will replace the storage compartment. See ªOnStar


Systemº in the Index for more information.
If your vehicle has the optional HomeLink Transmitter,
the buttons will replace the garage door opener
compartment. See ªHomeLink Transmitterº in the Index
for more information.
If your vehicle has a sunroof, the mini console contains
the HomeLink Transmitter buttons and the OnStar
buttons. The OnStar buttons are located behind the
overhead console.

2-73
Emergency Button: In an emergency situation,
press the emergency service button. Upon receiving the
call, an advisor at the center will locate your vehicle and
assess the situation. If necessary, the advisor will alert
the nearest emergency service provider.
Communication Button: Press this button at
the end of a call. Also press this button to answer a
call from the center, or cancel a call if one of the other
buttons is accidently pressed. This button is also used
to access OnStar Personal Calling and Virtual Advisor
Services. See the OnStar Owner package for more
information.
Volume Control: You can control the volume of
the OnStar System using either the volume control
knob on the radio or, if equipped, the steering wheel
volume control.
Telltale Light: This light will indicate the status of
the system. A solid green light will come on when you
start the vehicle to let you know that the system is on
and is ready to make or receive calls.
If the light blinks green it means that an incoming or
outgoing call is in progress. Press the Communication
button if you notice the light blinking and you are not
on a call.This light will be red in the event of an OnStar system
malfunction. If this occurs press the OnStar button to
attempt to contact an advisor. If the connection is made,
the advisor will assist you with steps to take to make
sure that the system is functioning properly. If you
cannot contact the advisor, take your vehicle to your
dealership as soon as possible for assistance.
Cellular Antenna: The cellular antenna on the outside
of your vehicle is critical to effective communication
using the OnStar system. Optimum Cellular reception
can be obtained when the mast is straight up and down.
OnStar Services
The following services are available within Onstar
service plans. Your vehicle comes with a specific
one
-year service plan that allows use of some or all of
the following services.
Automatic Notification of Air Bag Deployment: If an
air bag deploys, a priority emergency signal is
automatically sent to the center. An advisor will locate
your vehicle's position, try to contact you and assist you
in the situation. If the center is unable to contact you, an
emergency service provider will be contacted.

2-77
HomeLink
Transmitter (Option)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.
Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the ªstop and reverseº
safety feature. This includes any garage door opener
model manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand
-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
three HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.

2-78
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand
-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand
-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming the HomeLink, make
sure that you have followed the directions exactly as
described and that the battery in the hand
-held
transmitter is not weak. If you still cannot program it,
move the hand
-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to ªTraining a Garage Door Opener with
a `Rolling Code' Featureº next in this section or contact
the manufacturer of HomeLink at 1
-800-355-3515, or
on the internet at www.homelink.com.
Be sure to keep the original hand
-held transmitter in
case you need to erase and reprogram HomeLink.
Training a Garage Door Opener with a
ªRolling Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1
-800-355-3515, or on the internet at
www.homelink.com. Because of the steps involved,
it may be helpful to have another person assist in
programming the transmitter.
2. Press the Learn or Smart button on the garage
door opener motor head unit. An indicator light will
begin to flash when the motor head unit enters the
training mode.
Following this step, you have 30 seconds to
start Step 3.

2-79
3. Return to HomeLink in your vehicle and firmly
press and release the programmed HomeLink button
three times.
The rolling
-code garage door opener should now
recognize HomeLink. You may either use HomeLink or
the hand
-held transmitter to open the garage door.
If after following these instructions, you still have
problems training the garage door opener, contact the
manufacturer of HomeLink at 1
-800-355-3515, or on
the internet at www.homelink.com.
Canadian Programming
Canadian Owners: During programming, the
hand
-held transmitter may automatically stop
transmitting after two seconds. In this case, you should
press and hold the HomeLink button (see Steps 2 and 3
under ªProgramming the HomeLink Transmitterº) while
you press and repress (cycle) your hand
-held transmitter
every two seconds until HomeLink is trained.
Operating the HomeLink Transmitter
Press and hold the appropriate button on HomeLink for
at least a half of a second. The indicator light will come
on while the signal is being transmitted.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons on HomeLink until the indicator
light begins to flash (approximately 20 seconds).
Release both buttons.
Resetting Defaults
To reset HomeLink to default settings, hold down the
two outside buttons on HomeLink until the indicator
light begins to flash (approximately 20 seconds).
Continue to hold the buttons until the HomeLink
indicator light turns off and then release both buttons.
Accessories
Accessories for HomeLink are available. If you would
like additional information, please contact the
manufacturer of HomeLink at 1
-800-355-3515, or
on the internet at www.homelink.com.

2-124
To adjust the HUD so you can see it properly:
1. Start your engine and turn the dimmer knob to the
desired HUD image brightness.
The brightness of the HUD image is determined by
the ambient light conditions in the direction your
vehicle is facing and where you have the HUD
dimmer knob set. If you are facing a dark object or a
heavily shaded area, your HUD may anticipate that
you are entering a dark area and may begin to dim.
2. Adjust the driver's seat. If you change your seat
position later, you may have to readjust your HUD.
3. Press the UP or DN buttons until the HUD image is
easy to see and then press the DN button until the
HUD image is as low as possible, but, remains in full
view straight ahead near the front bumper.
The HUD image can only be adjusted up and down,
not side
-to-side.
4. To turn the image off, turn the dimmer knob
counterclockwise to OFF.
If the sun comes out or it becomes cloudy, you may need
to adjust the HUD brightness again using the dimmer
knob. Polarized sunglasses could make the HUD image
harder to see.When you first start the vehicle the display will show
BUICK and the Buick logo for a few seconds. If it is
cold outside, this display may stay on for up to a minute.
Clean the inside of the windshield as needed to remove
any dirt or film that reduces the sharpness or clarity of
the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry it.
Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you can't see the HUD image,
check one of the following:

The HUD unit is covered,

the HUD dimmer knob is adjusted correctly,

the HUD image is adjusted to the proper height,

ambient light (in the direction your vehicle is facing)
is low, or

a fuse is blown. See ªFuses and Circuit Breakersº in
the Index.
Keep in mind that your windshield is part of the HUD
system. If you ever have to have your windshield
replaced, be sure to get one that is designed for HUD or
your HUD image may look blurred and out of focus.

3-3
(Defog): This setting directs air to the windshield
and through the floor ducts. This mode is particularly
useful during cold or inclement weather because of your
vehicle's larger windshield area.
(Defrost): This setting directs most of the air to the
windshield and side window vents.
Mode Buttons
(Recirculation): Press this button (the light will
glow) to recirculate the air inside of your vehicle and to
limit the amount of outside air and/or odors entering
the vehicle.
Press this button again (the light will go off) to send
outside air into your vehicle. Using this setting while
trying to defrost or defog the windows will help clear
the vents of moisture. When the defog, defrost or lower
setting is selected, the system will automatically go to
outside air mode.
Operating the Heating/Ventilation/Air Conditioning
(HVAC) system in the recirculation mode may cause
fogging of the vehicle's windows when the weather
is cold and damp. To clear the fog, switch the HVAC
system to either the defog or defrost mode and increase
the fan speed. To avoid refogging of the windows,
operate the HVAC system in the outside air mode.Air Conditioning
On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.
To get maximum cooling or a quick cool
-down on
very hot days, press the A/C and recirculation buttons
(the lights will glow) and turn the temperature knob
counterclockwise (toward the blue area). Then, adjust
the mode knob to direct the air to the desired location.
This setting should not be used for long periods of time
because the air may become too cold and dry.
Push the A/C button again (the light will go off) to turn
off the air conditioning.
When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle's engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle's engine compartment when it is idling or
after it has been turned off. This is normal.

3-7
Mode Buttons
VENT: This button turns the air conditioning
compressor on and off and changes the mode to
upper. The words A/C OFF are shown in the display.
Recirculation is not permitted when the compressor
is off. The system will try to control the temperature
automatically, but without the compressor.
(Recirculation): Press this button
(the recirculation symbol in the display will be lit) to
recirculate the air inside of your vehicle and to limit the
amount of outside air and/or odors entering the vehicle.
Press this button again (the recirculation symbol will
go off) to send outside air into your vehicle. Using this
setting while trying to defrost or defog the windows will
help clear the vents of moisture. When the defog, defrost
or lower setting is selected, the system will
automatically go to outside air mode.
Operating the Heating/Ventilation/Air Conditioning
(HVAC) system in the recirculation mode may cause
fogging of the vehicle's windows when the weather
is cold and damp. To clear the fog, switch the HVAC
system to either the defog or defrost mode and increase
the fan speed. To avoid refogging of the windows,
operate the HVAC system in the outside air mode.Air Conditioning
On very hot days, your vehicle will cool down more
quickly and economically if you open the windows long
enough to let hot, inside air escape. For all settings,
adjust the temperature knob and fan speed as desired.
To get maximum cooling or a quick cool
-down on very
hot days, press the recirculation button (the recirculation
symbol in the display will be lit) and turn the
temperature knob to the desired interior temperature.
Then, select the mode to direct the air to the desired
location. This setting should not be used for long
periods of time because the air may become too cold
and dry.
Push the recirculation button again (the recirculation
symbol will go off) to turn off recirculation.
When the air conditioner compressor is on, you may
sometimes notice slight changes in your vehicle's engine
performance and power. This is normal. The system is
designed to help fuel economy while it maintains the
desired cooling level.
The air conditioner removes moisture from the air, so
you may sometimes notice water dripping from under
your vehicle's engine compartment when it is idling or
after it has been turned off. This is normal.