set clock BUICK RANDEZVOUS 2007 Owner's Manual

Reprogramming a Single Universal
Home Remote Button
To program a device to Universal Home Remote
using a Universal Home Remote button
previously trained, follow these steps:
1. Press and hold the desired Universal Home
Remote button. Do not release the button.
2. The indicator light will begin to ash after
20 seconds. While still holding the Universal
Home Remote button, proceed with Step 2
under “Programming Universal Home Remote”
shown earlier in this section.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 496.
Storage Areas
Glove Box
If the glove box has a lock, put your key into the
lock and turn the key counterclockwise. To
open the glove box, pull the latch release.
The glove box door has a set position that
prevents the door from lowering too far. Open the
glove box until the door is partway open, then
pull the door down if you need it fully opened.
To close the glove box, the door must be pushed up
past the set position. To lock the glove box, put your
key into the lock and turn the key clockwise.
Cupholder(s)
There are two cupholders located in the oor
console.
The cupholders have liners that remove for larger
beverage items. Remove the liners by lifting
them out.
158

To adjust the HUD so you can see it properly, do
the following:
1. Start your engine and turn the dimmer knob to
the desired HUD image brightness.
The brightness of the HUD image is determined
by the ambient light conditions in the direction
your vehicle is facing and where you have the
HUD dimmer knob set. If you are facing a dark
object or a heavily shaded area, your HUD may
anticipate that you are entering a dark area and
may begin to dim.
2. Adjust the driver’s seat. If you change your
seat position, you may have to readjust
your HUD.3. Press the UP or DN buttons until the HUD
image is easy to see and then press the DN
button until the HUD image is as low as
possible, but remains in full view straight
ahead near the front bumper.
The HUD image can only be adjusted up and
down, not side-to-side.
4. To turn the image off, turn the dimmer knob
counterclockwise until it stops.
If the sun comes out or it becomes cloudy, you
may need to adjust the HUD brightness again
using the dimmer knob. Polarized sunglasses
could make the HUD image harder to see.
When you rst start the vehicle the display will
show BUICK and the Buick logo for a few seconds.
If it is cold outside, this display may stay on for
up to a minute.
Clean the inside of the windshield as needed to
remove any dirt or lm that reduces the sharpness
or clarity of the HUD image.
195

4. Turn the bulb socket one-quarter of a turn
counterclockwise.
5. Pull the bulb assembly out from the lamp
housing.
6. Unhook the electrical connector by lifting up
the tabs and separate the connector from the
bulb base.
7. Install the new bulb into the electrical
connector. Push the bulb rmly enough so
that the tabs hook over the tab on the bulb.
8. Reverse the steps to reinstall.
9. Reinstall the lamp to its pocket by lining up
the mounting pin and pushing forward to set
the position.
10. Reinstall the screws removed in Step 2.
11. Close the liftgate.Taillamps and Back-Up Lamps
This procedure is for the liftgate-mounted taillamps
and back-up lamps. To replace one of these bulbs,
do the following:
1. Open the liftgate. SeeLiftgate on page 118
for more information.
2. Remove the panel inside the liftgate by lifting
the tabs and pulling the panel off.
3. Remove the seven
wing nuts and the
four outboard nuts
(two at each end).
4. Gently lower the liftgate.
5. Pull the lamp assembly directly rearward from
the vehicle.
402