BUICK REGAL 1998 Owners Manual

Shift Lock Release Parking Brake
P
1 2
If your vehicle’s battery
should
go dead or there is a
lack of electrical power, there
is an access slot that will allov
you
to override the PARK (P)
lock if your shifter is stuck
in
PARK (P).
J
To set the parking brake,
hold the regular brake pedal
down with your right foot.
Push down the parking
brake pedal with your
left foot.
The access slot is located beneath
a small cap on the
right side of the console shift panel.
To remove the cap,
use
a screwdriver or key. Then insert the key or
screwdriver into the slot, press down and hold. Make
sure you have your foot
on the brake pedal while you
are performing this procedure. You will now be able to
shift your vehicle out of PARK (P).
To release the parking brake, hold the regular brake
pedal down with your right foot and push the parking
brake pedal with your left foot. When
you lift your left
foot,
the parking brake pedal will follow it to the
released position.
A warning chime will sound if the parking brake is set,
the ignition
is on and the shift lever is not in PARK (P)
or NEUTRAL (N).
2-27
ProCarManuals.com

NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have to
replace them, and you could also damage other
parts of your vehicle.
If you are towing a trailer and parking on any hill, see
“Towing a Trailer” in the Index. That section shows
what to do first to keep the trailer from moving.
Shifting Into PARK (P)
1. Hold the brake pedal down with your right foot and
set the parking brake with your left foot.
-
It can be dangerous to get out of your vehicle if ’
the shift lever is not fully in PARK (P) with the
parking brake firmly set, Your vehicle can roll,
If
you have left the engine running, the vehicle can
move suddenly. You or others could be injured.
To be sure your vehicle won’t move, even when
you’re on fairly level ground, use the steps that
follow. If you’re pulling
a trailer, see ‘(Towing a
Trailer” in the Index.
2-28
ProCarManuals.com

2. Move the shift lever into
the PARK
(P) position
like this:
0 Hold in the button on the lever, then push the lever
all the way toward the front
of your vehicle.
0 Move the ignition key to LOCK.
3. Remove the key and take it with you. If you can
leave your vehicle with the ignition key in your
hand, your vehicle is in PARK
(P).
Leaving Your Vehicle With the
Engine Running
It can be dangerous to leave your vehicle with the
engine running. Your vehicle could move
suddenly if the shift lever is not fully
in PARK (P)
with the parking brake firmly set. And, if you
leave the vehicle with the engine running, it could
overheat and even catch fire. You
or others could
be injured. Don’t leave your vehicle with the
engine running unless
you have to.
.~
If you have to leave your vehicle with the engine
running, be sure your
vehicle is in PARK (P) and your
parking brake is firmly set before
you leave it. After
you’ve moved the shift lever into the PARK
(P)
position, hold the regular brake pedal down. Then, see if
you can move the shift lever out
of PARK (P) without
first pushing the button. If you can, it means that the
shift lever wasn’t
fully locked into PARK (P).
2-29
ProCarManuals.com

Torque Lock
If you are parking on a hill and you don’t shift your
transaxle into
PARK (P) properly, the weight of the
vehicle may put too much force on the parking pawl
in
the transaxle. You may find it difficult to pull the shift
lever out of PARK (P). This is called “torque lock.” To
prevent torque lock, set the parking brake and then shift
into PARK (P) properly before
you leave the driver’s
seat. To find out how, see “Shifting Into PARK
(P)” in
the Index.
When you are ready to drive, move the shift lever out of
PARK (P)
before you release the parking brake.
If torque lock does occur, you may need
to have another
vehicle push yours
a little uphill to take some of the
pressure from the parking pawl in the transaxle, so you
can pull the shift lever out of PARK (P).
Shifting Out of PARK (P)
Your vehicle has a Brake-Transaxle Shift Interlock
(BTSI).
You must fully apply your regular brakes
before you can shift from PARK
(P) when the ignition is
in RUN. See “Automatic Transaxle Operation” in
the Index.
If you cannot shift out
of PARK (P), ease pressure on
the shift lever by pushing it all the way into PARK
(P)
while keeping the brake pedal pushed down. Release the
shift lever button. Then move the shift lever out of
PARK
(P).
If you ever hold the brake pedal down but still can’t
shift out of PARK
(P), try this:
1. Turn the ignition key to OFF.
2. Apply and hold the brake until the end of Step 4.
3. Shift to NEUTRAL (N).
4. Start the engine and shift to the drive gear you want.
5. Have the vehicle fixed as soon as you can.
2-30
ProCarManuals.com

Parking Over Things That Burn Engine Exhaust
. .. :' ' :'!
Things that can burn could touch hot exhaust
parts under your vehicle and ignite. Don't park
over papers, leaves, dry grass or other things that
can burn. Engine exhaust can
kill.
It contains the gas
carbon monoxide
(CO), which you can't see or
smell. It can cause unconsciousness and death.
You might have exhaust coming in if:
0 Your exhaust system sounds strange
Your vehicle gets rusty underneath.
0 Your vehicle was damaged in a collision.
0 Your vehicle was damaged when driving over
high points on the road or over road debris.
Repairs weren't done correctly.
0 Your vehicle or exhaust system had been
or
different.
modified improperly.
If you ever suspect exhaust is coming into
your vehicle:
0 Drive it only with all the windows down
0 Have your vehicle fixed immediately.
blow
out any
CO; and to
2-31
ProCarManuals.com

Running Your Engine While
You’re Parked
It’s better not to park with the engine running. But if you
ever have to, here are
some things to know.
Idling the engine with the climate control
system off could allow dangerous exhaust into
your vehicle (see the earlier Caution under
“Engine Exhaust”).
Also, idling in a closed-in place can let deadly
carbon monoxide
(CO) into your vehicle even if
the fan switch is
at the highest setting. One place
this can happen is
a garage. Exhaust -- with
CO -- can come in easily. NEVER park in a
garage with the engine running.
Another closed-in place can be a blizzard. (See “Blizzard” in the Index.)
I
It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK
(P) with the
parking brake firmly set. Your vehicle can roll.
Don’t leave your vehicle when the engine is
running unless you have to. If you’ve left the
engine running, the vehicle can move suddenly.
You or others could be injured.
To be sure your
vehicle won’t move, even when you’re on fairly
level ground, always set your parking brake and
move the shift lever to
PARK (P).
Follow the proper steps to be sure your vehicle won’t
move. See “Shifting
Tnto PARK (P)” in the Index.
If you are parking on a hill and if you’re pulling a
trailer, also see “Towing
a Trailer” in the Index.
2-32
ProCarManuals.com

Windows
Power Windows
Switches on the driver’s door armrest control each of the
windows when the ignition is on. In addition, each
passenger’s door has a switch for its own window. The driver’s
window switch has
an express-down
feature. This switch is labeled AUTO. Tap the rear of
the switch, and the driver’s window will open
a small
amount.
If the rear of the switch is pressed all the way
down, the window will go all the way down.
To stop the window while it is lowering, press the front
of the switch. To raise the window, press and hold the
front
of the switch.
The driver’s window controls also include a lock-out
switch. Press
LOCK to stop front and rear passengers
from using their window switches. The driver can still
control all the windows with the lock on. Press the other
side of the
LOCK button for normal window operation.
Horn
Press anywhere near the horn symbols on your steering
wheel pad to sound the horn.
2-33
ProCarManuals.com

TILT-WHEEL TM Adjustable
Steering Column
A tilt steering wheel allows
you to adjust the steering
wheel before
you drive. You
can also raise it to the
highest level to give your
legs more room when you
exit and enter the vehicle.
To tilt the wheel, hold the steering wheel and pull the
lever. Move the steering wheel to a comfortable level,
then release the lever to lock the wheel into place.
Turn SignaYMultifunction Lever
The lever on the left side of the steering column
includes your:
0 Turn Signal and Lane Change Indicator
Headlamp High/Low Beam Changer
0 Windshield Wipers
Windshield Washer
Cruise Control (Option)
0 Flash-to-Pass
2-34
ProCarManuals.com

Turn Signal and Lane Change Indicator
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
An arrow on
the instrument
panel will flash in the
direction
of the turn or
lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return
by
itself when you release it.
If the arrow flashes faster than normal as you signal a
turn or a lane change, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the arrows don’t go on at all when
you
signal a turn, check for burned-out bulbs and then check
the fuse (see “Fuses and Circuit Breakers” in the Index).
A chime will sound if
you leave your turn signal on for
more than
314 mile (1.2 km).
Headlamp High/Low Beam Changer
To change your headlamps
from low beams to high
beams,
or high to low, pull
the multifunction lever all
the way toward you. Then
release it.
When the high beams are on, this light
on the instrument
panel also will be
on.
2-35
ProCarManuals.com

Flash-to-Pass Feature
This feature lets you use your high-beam headlamps to
signal the driver in front of you that you want
to pass. It
works even if your headlamps are off.
To use it, pull the turn signal lever toward you a little,
but not
so far that you hear a click.
If your headlamps are off or
on low beam, your
high-beam headlamps will turn on. They’ll stay on as
long as you hold the lever toward
you and the
high-beam indicator
on the dash will come on. Release
the lever to turn the high-beam headlamps off.
Windshield Wipers
You control the windshield wipers by turning the band
marked
WIPER. For a single wiping cycle, turn the band
to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on
MIST longer.
2-36
ProCarManuals.com