windshield wipers BUICK REGAL 1998 Owners Manual

1 sw Vehicle “Break-In” Ignition
Positions
NOTICE:
Your vehicle doesn’t need an elaborate
“break-in.” But it will perform better in the long
run if you follow these guidelines:
0 Don’t drive at any one speed -- fast or
slow -- for the first 500 miles (805 km).
Don’t make full-throttle starts.
200 miles (322 km) or so. During this time
your new brake linings aren’t yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every
time you get new brake linings.
See “Towing a Trailer” in the Index for
more information.
0 Avoid making hard stops for the first
Don’t tow a trailer during break-in.
A L
With the ignition key in the ignition, you can turn tne
switch to five positions:
ACCESSORY
(A): The accessory position lets you use
the radio and windshield wipers when the engine
is off.
To use ACC, push in the key and turn it toward you.
Your steering wheel will stay locked.
2-17
ProCarManuals.com

TILT-WHEEL TM Adjustable
Steering Column
A tilt steering wheel allows
you to adjust the steering
wheel before
you drive. You
can also raise it to the
highest level to give your
legs more room when you
exit and enter the vehicle.
To tilt the wheel, hold the steering wheel and pull the
lever. Move the steering wheel to a comfortable level,
then release the lever to lock the wheel into place.
Turn SignaYMultifunction Lever
The lever on the left side of the steering column
includes your:
0 Turn Signal and Lane Change Indicator
Headlamp High/Low Beam Changer
0 Windshield Wipers
Windshield Washer
Cruise Control (Option)
0 Flash-to-Pass
2-34
ProCarManuals.com

Flash-to-Pass Feature
This feature lets you use your high-beam headlamps to
signal the driver in front of you that you want
to pass. It
works even if your headlamps are off.
To use it, pull the turn signal lever toward you a little,
but not
so far that you hear a click.
If your headlamps are off or
on low beam, your
high-beam headlamps will turn on. They’ll stay on as
long as you hold the lever toward
you and the
high-beam indicator
on the dash will come on. Release
the lever to turn the high-beam headlamps off.
Windshield Wipers
You control the windshield wipers by turning the band
marked
WIPER. For a single wiping cycle, turn the band
to
MIST. Hold it there until the wipers start, then let go.
The wipers will stop after one cycle. If you want more
cycles, hold the band on
MIST longer.
2-36
ProCarManuals.com

For steady wiping at low speed, turn the band to LO. For
high-speed wiping, turn the band further, to HI. To stop
the wipers, turn the band to
OFF.
You can set the wiper speed for a long or short delay
between wipes, This can be very
useful in light rain or
snow. Turn the band
to choose the delay time. The
closer to
LO, the shorter the delay between wipes.
Be sure to clear ice and snow from the wiper blades
before using them. If they’re frozen to the windshield,
carefully loosen or thaw them. If your blades
do become
damaged, get new blades or blade inserts.
Heavy snow or ice can overload your wipers. A circuit
breaker will stop them until the motor cools. Clear away
snow or ice
to prevent an overload.
Windshield Washer
At the top of the multifunction lever, there’s a paddle with
the word
PUSH on it. To spray washer fluid on the
windshield, push the paddle. The wipers will run for
several sweeps and then either stop or return to your preset
speed. See “Windshield Washer Fluid”
in the Index.
I
A CAUTICU: I
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
The LOW WASH light on
your instrument panel
cluster will glow when the
LOW WASH fluid level is low.
2-37
ProCarManuals.com

To change the passenger compartment air filter, use the
following steps:
1. Turn off the ignition when the windshield wipers
are in the up position.
2. Raise the hood.
3. Remove (disconnect) the windshield washer pump
hose from the fender rail and air inlet grille.
4. Reposition the hood weatherstrip from the right
side
of the vehicle (peel back halfway to center).
5. Remove (disconnect) the air inlet grille retainers.
6. Remove (disconnect) the air inlet grille.
7. Remove (disconnect) the passenger compartment
8. Then install the new air filter. For the type of filter
to use, see “Normal Maintenance Replacement
Parts” in the Index.
air
filter.
9. Reposition the air inlet grille.
10. Replace the air inlet grille retainers. 11.
Reposition the hood weatherstrip.
12. Reconnect the windshield washer pump hose to the
fender rail and air inlet grille.
13. Close the hood.
14. Return the windshield wipers to the park position.
Supercharger Oil
Unless you are technically qualified and have the proper
tools,
you should let your dealer or a qualified service
center perform this maintenance.
When to Check
Check oil level every 30,000 miles (50 000 km) or every
36 months, whichever occurs first.
What Kind of Oil to Use
See “Recommended Fluids and Lubricants” in the Index
and use only the recommended oil.
6-19
ProCarManuals.com

Dome Lamp
1.
2.
3.
4.
5.
6.
7.
8.
Grasp the front center and rear center positions
of the dome lamp housing and squeeze together until
the housing releases from the base plate.
A
flat-bladed screwdriver may be necessary to pry the
assembly loose.
Lift the plastic locking tab on the electrical
connector and pull the connector from the dome
lamp assembly.
Grasp the bulb housing located in the center
of the
assembly and pull straight up.
Pull the bulb out
of the socket.
Push in a new bulb.
Replace the socket into the dome lamp assembly.
Reconnect the dome lamp assembly to the wiring
harness, making sure the connector tab snaps
into place.
Reposition the dome lamp assembly
to the roof, and
gently push the assembly into the base plate. 1. Turn
on the wipers to the low wipe setting.
For any bulb changing procedure
not listed in this
section, contact your dealer service department.
Windshield Wiper Blade Replacement
6-41
ProCarManuals.com

2. Turn off the ignition while the wipers are at the
outer positions of the wiper pattern. The blades are
more accessible for removalh-eplacement while in
this position.
3. Pull the windshield wiper arm 3 to 4 inches
(7.5 to 10 cm) away from the windshield.
4. While holding the wiper arm away from the glass,
push the release clip from under the blade
connecting point and pull the blade assembly down
toward the glass to remove it from the wiper arm.
5. Push the new wiper blade securely on the wiper arm
until
you hear the release clip “click” into place.
For wiper blade replacement length and type, see
“Capacities and Specifications”
in the Index.
Tires
Your new vehicle comes with high-quality tires made by
a leading tire manufacturer. If you ever have questions
about your tire warranty and where
to obtain service, see
your Buick Warranty booklet for details.
Poorly maintained and improperly used tires
are dangerous.
Overloading your tires can cause
overheating
as a result of too much friction.
You could have an air-out and
a serious
accident. See “Loading Your Vehicle” in
the Index.
Underinflated tires pose the same danger as
overloaded tires. The resulting accident
could cause serious injury. Check all tires
frequently to maintain the recommended
pressure. Tire pressure should be checked
when your tires are cold.
Overinflated tires are more likely to be cut,
punctured or broken by a sudden impact
--
such as when you hit a pothole. Keep tires
at the recommended pressure.
Worn, old tires can cause accidents. If your
tread
is badly worn, or if your tires have
been damaged, replace them.
6-42
ProCarManuals.com

Electrical System
Add-on Electrical Equipment
1 NOTICE:
Don’t add anything electrical to your vehicle
unless you check with your dealer first. Some
electrical equipment can damage your vehicle and the damage wouldn’t be covered by your
warranty. Some add-on electrical equipment
can keep other components from working as
they should.
Your vehicle has an air bag system. Before attempting to
add anything electrical to your vehicle, see “Servicing
Your Air Bag-Equipped Vehicle” in the Index.
Headlamp Wiring
The headlamp wiring is protected by a circuit breaker in
the underhood electrical center. An electrical overload
will cause the lamps to
go on and off, or in some cases
to remain off. If this happens, have your headlamp
system checked right away.
Windshield Wipers
The windshield wiper motor is protected by a circuit
breaker and a fuse. If the motor overheats due to heavy
snow, etc., the wiper will stop until the motor cools. If
the overload is caused by some electrical problem, have
it fixed.
Power Windows and Other Power Options
Circuit breakers in the fuse panel protect the power
windows and other power accessories. When the current
load is too heavy, the circuit breaker opens and closes,
protecting
the circuit until the problem is fixed.
6-61
ProCarManuals.com

warning Devices ............................... 5-2
Warning Lights. Gages and Indicators
............... 2-59
Warranty Information
............................. 8-8
Washing Your Vehicle ........................... 6-53
Weatherstrips
.................................. 6-55
Wheel Alignment
.................................. 6-46
NutTorque
............................. 5-34. 6-43
Replacement
................................. 6-47
Used Replacement
............................ 6-48
WindowLock
.................................. 2-33
Windows
..................................... 2-33 Auto-Down
................................. 2-33
Power
...................................... 2-33
Windshield Washer
............................. 2-37
Fluid
.................................. 2.37. 6.28
Fluid Level Check
............................ 7-14
Windshield Wipers .............................. 2-36
Blade Replacement
........................... 6-41
Fuses
...................................... 6-61
Winter Driving
................................. 4-27
WiperBladeCheck
............................. 7-15
Wiring. Headlamp
.............................. 6-59
WreckerTowing
................................. 5-8
9-13
ProCarManuals.com