flat tire CADILLAC CT4 2023 Owner's Guide

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 439
Tire Sealant and
Compressor Kit
{Warning
Idling a vehicle in an
enclosed area with poor
ventilation is dangerous.
Engine exhaust may enter
the vehicle. Engine exhaust
contains carbon monoxide
(CO) which cannot be seen
or smelled. It can cause
unconsciousness and even
death. Never run the engine
in an enclosed area that has
no fresh air ventilation. For
more information, see
Engine Exhaust0271.
{Warning
Overinflating a tire could
cause the tire to rupture
and you or others could be
injured. Be sure to read and
follow the tire sealant and
compressor kit instructions
and inflate the tire to its
recommended pressure. Do
not exceed the
recommended pressure.
{Warning
Storing the tire sealant and
compressor kit or other
equipment in the passenger
compartment of the vehicle
could cause injury. In a
sudden stop or collision,
loose equipment could strike
someone. Store the tire
sealant and compressor kit
in its original location. If this vehicle has a tire sealant
and compressor kit, there may
not be a spare tire or tire
changing equipment, and on
some vehicles there may not
be a place to store a tire.
The tire sealant and
compressor can be used to
temporarily seal punctures up
to 6 mm (0.25 in) in the tread
area of the tire. It can also be
used to inflate an
underinflated tire.
If the tire has been separated
from the wheel, has damaged
sidewalls, or has a large
puncture, the tire is too
severely damaged for the tire
sealant and compressor kit to
be effective. See Roadside
Assistance Program
0487.
Read and follow all of the tire
sealant and compressor kit
instructions.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
440 Vehicle Care
The kit includes:
1. Sealant Canister InletValve
2. Sealant/Air Hose
3. Base of Sealant Canister
4. Tire Sealant Canister
5. On/Off Button
6. Slot on Top of Compressor
7. Pressure Deflation Button
8. Pressure Gauge
9. Power Plug
10. Air Only Hose
Tire Sealant
Read and follow the safe
handling instructions on the
label adhered to the tire
sealant canister (4).
Check the tire sealant
expiration date on the tire
sealant canister. The tire
sealant canister (4) should be
replaced before its expiration
date. Replacement tire sealant
canisters are available at your
local dealer. There is only enough sealant
to seal one tire. After usage,
the tire sealant canister must
be replaced.
Using the Tire Sealant and
Compressor Kit to
Temporarily Seal and
Inflate a Punctured Tire
When using the tire sealant
and compressor kit during cold
temperatures, warm the kit in
a heated environment for
five minutes. This will help to
inflate the tire faster.
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers
0149.
See If a Tire Goes Flat 0437
for other important safety
warnings.
Do not remove any objects
that have penetrated the tire.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 441
1. Remove the tire sealantcanister (4) and
compressor from its
storage location. See
Storing the Tire Sealant
and Compressor Kit 0446.
2. Remove the air only hose (10) and the power plug (9)
from the bottom of the
compressor.
3. Place the compressor on the ground near the
flat tire.4. Attach the air only hose(10) to the sealant canister
inlet valve (1) by turning it
clockwise until tight.
5. Slide the base of the tiresealant canister (3) into
the slot on the top of the
compressor (6) to hold it
upright.
Make sure the tire valve
stem is positioned close to
the ground so the hose will
reach it. 6. Remove the valve stem
cap from the flat tire by
turning it
counterclockwise.7. Attach the sealant/airhose (2) to the tire valve
stem by turning it
clockwise until tight.
8. Plug the power plug (9) into the accessory power
outlet in the vehicle.
Unplug all items from other
accessory power outlets.
See Power Outlets 0101.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
442 Vehicle Care
If the vehicle has an
accessory power outlet, do
not use the cigarette
lighter.
If the vehicle only has a
cigarette lighter, use the
cigarette lighter.
Do not pinch the power
plug cord in the door or
window.
9. Start the vehicle. The vehicle must be running
while using the air
compressor.
10. Press the on/off button (5) to turn the tire sealant and
compressor kit on.
The compressor will inject
sealant and air into
the tire.
The pressure gauge (8) will
initially show a high
pressure while the
compressor pushes the
sealant into the tire. Once
the sealant is completely
dispersed into the tire, the
pressure will quickly drop and start to rise again as
the tire inflates with
air only.
11. Inflate the tire to the recommended inflation
pressure using the
pressure gauge (8). The
recommended inflation
pressure can be found on
the Tire and Loading
Information label. See Tire
Pressure 0422.
The pressure gauge (8)
may read higher than the
actual tire pressure while
the compressor is on. Turn
the compressor off to get
an accurate pressure
reading. The compressor
may be turned on/off until
the correct pressure is
reached.
Caution
If the recommended
pressure cannot be reached
after approximately
25 minutes, the vehicle (Continued)
Caution (Continued)
should not be driven farther.
The tire is too severely
damaged and the tire
sealant and compressor kit
cannot inflate the tire.
Remove the power plug
from the accessory power
outlet and unscrew the
inflating hose from the tire
valve. See Roadside
Assistance Program 0487.
12. Press the on/off button (5) to turn the tire sealant and
compressor kit off.
The tire is not sealed and
will continue to leak air
until the vehicle is driven
and the sealant is
distributed in the tire.
Therefore, Steps 13–
21 must be done
immediately after Step 12.
Be careful while handling
the tire sealant and
compressor kit as it could
be warm after usage.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 443
13. Unplug the power plug (9)from the accessory power
outlet in the vehicle.
14. Turn the sealant/air hose (2) counterclockwise
to remove it from the tire
valve stem.
15. Replace the tire valve stem cap.
16. Remove the tire sealant canister (4) from the slot
on top of the
compressor (6).
17. Turn the air only hose (10) counterclockwise to
remove it from the tire
sealant canister inlet
valve (1).
18. Turn the sealant/air hose (2) clockwise onto the
sealant canister inlet
valve (1) to prevent sealant
leakage.
19. Return the air only hose (10) and power plug (9)
back to their original
storage location.
20. If the flat tire was able toinflate to the
recommended inflation
pressure, remove the
maximum speed label from
the sealant canister and
place it in a highly visible
location.
Do not exceed the speed
on this label until the
damaged tire is repaired or
replaced.
21. Return the equipment to its original storage location
in the vehicle.
22. Immediately drive the vehicle 8 km (5 mi) to
distribute the sealant in
the tire. 23. Stop at a safe location and
check the tire pressure.
Refer to Steps 1–10 under
“Using the Tire Sealant and
Compressor Kit without
Sealant to Inflate a Tire
(Not Punctured).”
If the tire pressure has
fallen more than 68 kPa
(10 psi) below the
recommended inflation
pressure, stop driving the
vehicle. The tire is too
severely damaged and the
tire sealant cannot seal the
tire. See Roadside
Assistance Program 0487.
If the tire pressure has not
dropped more than 68 kPa
(10 psi) from the
recommended inflation
pressure, inflate the tire to
the recommended inflation
pressure.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
444 Vehicle Care
24. Wipe off any sealant fromthe wheel, tire, or vehicle.
25. Dispose of the used tire sealant canister (4) at a
local dealer or in
accordance with local
state codes and practices.
26. Replace it with a new canister available from
your dealer.
27. After temporarily sealing a tire using the tire sealant
and compressor kit, take
the vehicle to an
authorized dealer within
161 km (100 mi) of driving
to have the tire repaired or
replaced.Using the Tire Sealant and
Compressor Kit without
Sealant to Inflate a Tire
(Not Punctured)
The kit includes:
1. Sealant Canister Inlet Valve
2. Sealant/Air Hose
3. Base of Sealant Canister
4. Tire Sealant Canister
5. On/Off Button
6. Slot on Top of Compressor 7. Pressure Deflation
Button
8. Pressure Gauge
9. Power Plug
10. Air Only Hose
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers 0149.
See If a Tire Goes Flat 0437
for other important safety
warnings.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 445
1. Remove the compressorfrom its storage location.
See Storing the Tire
Sealant and Compressor
Kit 0446.
2. Remove the air only hose (10) and the power plug (9)
from the bottom of the
compressor.
3. Place the compressor on the ground near the
flat tire.
Make sure the tire valve
stem is positioned close to
the ground so the hose will
reach it.
4. Remove the valve stem cap from the flat tire by
turning it
counterclockwise.
5. Attach the air only hose (10) to the tire valve stem
by turning it clockwise until
tight.
6. Plug the power plug (9) into the accessory power
outlet in the vehicle. Unplug all items from other
accessory power outlets.
See Power Outlets
0101.
If the vehicle has an
accessory power outlet, do
not use the cigarette
lighter.
If the vehicle only has a
cigarette lighter, use the
cigarette lighter.
Do not pinch the power
plug cord in the door or
window.
7. Start the vehicle. The vehicle must be running
while using the air
compressor.
8. Press the on/off button (5) to turn the tire sealant and
compressor kit on.
The compressor will inflate
the tire with air only.
9. Inflate the tire to the recommended inflation
pressure using the
pressure gauge (8). The
recommended inflation
pressure can be found on the Tire and Loading
Information label. See Tire
Pressure
0422.
The pressure gauge (8)
may read higher than the
actual tire pressure while
the compressor is on. Turn
the compressor off to get
an accurate pressure
reading. The compressor
may be turned on/off until
the correct pressure is
reached.
Caution
If the recommended
pressure cannot be reached
after approximately
25 minutes, the vehicle
should not be driven farther.
The tire is too severely
damaged and the tire
sealant and compressor kit
cannot inflate the tire.
Remove the power plug
from the accessory power
outlet and unscrew the (Continued)

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
446 Vehicle Care
Caution (Continued)
inflating hose from the tire
valve. See Roadside
Assistance Program0487.
10. Press the on/off button (5) to turn the tire sealant and
compressor kit off.
Be careful while handling
the compressor as it could
be warm after usage.
11. Unplug the power plug (9) from the accessory power
outlet in the vehicle.
12. Turn the air only hose (10) counterclockwise to
remove it from the tire
valve stem.
13. Replace the tire valve stem cap.
14. Return the air only hose (10) and power plug (9)
back to their original
storage location. 15. Return the equipment to
its original storage location
in the vehicle.
The tire sealant and
compressor kit has accessory
adapters located in a
compartment on the bottom
of its housing that can be used
to inflate air mattresses,
balls, etc.
Storing the Tire
Sealant and
Compressor Kit
The tire sealant and
compressor kit is in a bag in
the trunk. 1. Open the trunk. See Trunk 022.
2. Lift the load floor.
3. Remove the tire sealant and compressor kit bag.
4. Remove the tire sealant and compressor kit from
the bag.
To store the tire sealant and
compressor kit, reverse the
steps.

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
450 Vehicle Care
After starting the disabled
vehicle and removing the
jumper cables, allow it to idle
for several minutes.
Towing the
Vehicle
Transporting a
Disabled Vehicle
(Electronic Shifter)
Caution
Incorrectly transporting a
disabled vehicle may cause
damage to the vehicle. Use
proper tire straps to secure
the vehicle to the flatbed
tow truck. Do not strap or
hook to any frame,
underbody, or suspension
component not specified
below. Do not move vehicles
with drive axle tires on the
ground. Damage is not
covered by the vehicle
warranty.
Caution
The vehicle may be equipped
with an electric parking
brake and/or an electronic
shifter. In the event of a loss
of 12-volt battery power, the
electric parking brake
cannot be released, and the
vehicle cannot be shifted to
N (Neutral). Tire skates or
dollies must be used under
the non-rolling tires to
prevent damage while
loading/unloading the
vehicle. Dragging the vehicle
will cause damage not
covered by the vehicle
warranty.
Caution
The vehicle may be equipped
with a tow eye. Improper use
of the tow eye may cause
damage to the vehicle and is
not covered by the vehicle
warranty. If equipped, use(Continued)
Caution (Continued)
the tow eye to load the
vehicle onto a flatbed tow
truck from a flat road
surface, or to move the
vehicle a very short distance
at a walking pace. The tow
eye is not designed for
off-road recovery. The
vehicle must be in
N (Neutral) with the electric
parking brake released when
using the tow eye.
Contact a professional towing
service if the disabled vehicle
must be transported. GM
recommends a flatbed tow
truck to transport a disabled
vehicle. Use ramps to help
reduce approach angles,
if necessary.
If equipped, a tow eye may be
located near the spare tire or
emergency jack. Do not use
the tow eye to pull the vehicle
from the snow, mud, sand,
or ditch. Tow eye threads may

Cadillac CT4 Owner Manual (GMNA-Localizing-U.S./Canada-16500442) -
2023 - CRC - 5/4/22
Vehicle Care 451
have right or left-hand
threads. Use caution when
installing or removing the
tow eye.
The vehicle must be in
N (Neutral) and the electric
parking brake must be
released when loading the
vehicle onto a flatbed tow
truck.
.If the vehicle is equipped
with car wash mode and has
12-volt battery power, refer
to“Car Wash Mode” under
Automatic Transmission
(Mechanical Shifter) 0272 or
Automatic Transmission
(Electronic Shifter) 0275 to
place the vehicle in
N (Neutral).
.If the 12-volt battery is dead
and/or the engine will not
start, the vehicle will not
move. Try to jump start the
vehicle. Refer to Jump
Starting - North America
0 447 and if the jump start is
successful, retry the “Car
Wash Mode” procedure.
.If jump starting is
unsuccessful, the vehicle will
not move. Tire skates or
dollies must be used under
the non-rolling tires to
prevent vehicle damage.
V-Series Blackwing Only
Due to low ramp angles on the
V-Series Blackwing, use care
when loading the vehicle onto
a flatbed carrier. Front spring
spacers were provided for
lifting the front suspension if
more clearance is necessary
when towing.
Front Tow Eye
The vehicle is equipped with a
tow eye. Only use the tow eye
to pull the vehicle onto a
flatbed car carrier from a flat
road surface. Do not use the
tow eye to pull the vehicle
from snow, mud, or sand. The
tow eye is located under the
carpet in the trunk.
Carefully open the cover in the
fascia by using the small notch
that conceals the tow eye
socket.