battery CADILLAC CTS 2003 1.G User Guide

2-73
OnStar System Limitations
Complete limitations can be found on the Subscriber
Services Agreement.
In order to provide you with excellent service, calls with
the OnStar Center may be monitored or recorded.
OnStar service is:

available in the 48 contiguous United States, Alaska,
Hawaii and Canada;

available when the vehicle is within the operating
range of a cellular provider;

subject to limitations caused by atmospheric
conditions, such as severe weather or topographical
conditions, such as mountainous terrain;

subject to cellular carrier equipment limitations.
Global positioning locating capabilities will not be
available if satellite signals are obstructed.
OnStar will not function if the vehicle's battery is
discharged or disconnected. It may also be inoperative if
the vehicle is in an accident and the OnStar or vehicle
electrical system components are damaged.OnStar is the communication link between you and
existing governmental emergency and roadside service
providers. OnStar will receive your call and use
reasonable effort to contact an appropriate provider.
OnStar cannot promise that the providers will respond in
a timely manner or at all.
OnStar Steering Wheel Controls
You can use the steering wheel controls to interact with
the OnStar system. See the OnStar manual provided
with your vehicle for more information. Some steering
wheel controls can be programmed to interact with
OnStar. See ªReconfigurable Steering Wheel Controlsº
in the Index for more information.
Assist Handles
The assist handles are located above the rear doors. Use
them to help you enter and exit the vehicle.
Garment Hooks
The garment hooks are part of the assist handles located
above the rear doors.

2-75
HomeLink
Transmitter
(If Equipped)
A. HomeLink
Transmitter
Buttons
B. Travel Note
Recorder Buttons
(If Equipped)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference, including interference
that may cause undesired operation of the device.Changes and modifications to this system by other than
an authorized service facility could void authorization to
use this equipment.
Programming the HomeLink Transmitter
Do not use the HomeLink Transmitter with any garage
door opener that does not have the ªstop and reverseº
feature. This includes any garage door opener model
manufactured before April 1, 1982.
Be sure that people and objects are clear of the garage
door you are programming.
It is recommended that a new battery be installed in
your hand
-held transmitter for quicker and more
accurate transmission of the radio frequency.
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. Decide which one of the three channels (one of the
HomeLink buttons) you want to program.
2. Press and hold the desired button on HomeLink
through Step 3.

2-76
3. When the HomeLink indicator light begins to blink
slowly (this may take up to 30 seconds), hold the
hand
-held transmitter about 1 to 3 inches (3 to 8 cm)
away from HomeLink and then press and hold the
transmit button on the hand
-held transmitter.
Continue to hold both buttons until the indicator
light on HomeLink begins to flash rapidly (this may
take up to 90 seconds).
If you have trouble programming HomeLink, make sure
that you have followed the directions exactly as
described and that the battery in the hand
-held
transmitter is not weak. If you still cannot program it,
move the hand
-held transmitter to the left or right or
forward or backward or flip it upside down. HomeLink
may not work with older garage door openers that do
not meet current Federal Consumer Safety Standards.
If you cannot program the transmitter after repeated
attempts, refer to ªTraining a Garage Door Opener with
a `Rolling Code' Featureº next in this section or contact
the manufacturer of HomeLink at 1
-800-355-3515, or
on the internet at www.homelink.com.
Be sure to keep the original hand
-held transmitter in
case you need to erase and reprogram HomeLink.
Training a Garage Door Opener with a
ªRolling Codeº Feature (If Equipped)
If you have not previously programmed the hand-held
transmitter to HomeLink, see ªProgramming the
HomeLink Transmitterº listed previously. If you have
completed this programming already, you now need to
train the garage door opener motor head unit to
recognize HomeLink.
1. Find the ªLearnº or ªSmartº button on the garage
door opener motor head unit. The exact location and
color will vary by garage door opener brand. If you
have difficulty finding the Learn or Smart button,
refer to your garage door opener owner's manual or
contact the manufacturer of HomeLink at
1
-800-355-3515, or on the internet at
www.homelink.com.
Because of the steps involved, it may be helpful to
have another person assist in programming the
transmitter.

2-87
CAUTION:
If the air bag readiness light stays on after you
start your vehicle, it means the air bag system
may not be working properly. The air bags in
your vehicle may not inflate in a crash, or they
could even inflate without a crash. To help avoid
injury to yourself or others, have your vehicle
serviced right away if the air bag readiness light
stays on after you start your vehicle.
The air bag readiness light should flash for a few
seconds when you turn the ignition key to ON. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.
If there is a problem with the air bag system in your
vehicle, the Service Air Bag message will appear on the
DIC display. See ªService Air Bag Messageº later in
this section for more information.
Charging System Light
When you turn the key to
ON or START, this light
will come on briefly to
show that the generator and
battery charging systems are
working properly.
If this light stays on, your vehicle needs service. You
should take your vehicle to the dealer at once. To save
your battery until you get there, turn off all accessories.

2-94
Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel. See
ªFuelº in the Index. Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start
-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience one or more of these conditions,
change the fuel brand you use. It will require at least one
full tank of the proper fuel to turn the light off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and
diagnostic tools to fix any mechanical or electrical
problems that may have developed.Emissions Inspection and Maintenance Programs
Some state/provincial and local governments have or
may begin programs to inspect the emission control
equipment on your vehicle. Failure to pass this
inspection could prevent you from getting a vehicle
registration.
Here are some things you need to know in order to help
your vehicle pass an inspection:
Your vehicle will not pass this inspection if the CHECK
ENGINE light is on or not working properly.
Your vehicle will not pass this inspection if the OBD
(on
-board diagnostic) system determines that critical
emission control systems have not been completely
diagnosed by the system. The vehicle would be
considered not ready for inspection. This can happen if
you have recently replaced your battery or if your
battery has run down. The diagnostic system is designed
to evaluate critical emission control systems during
normal driving. This may take several days of routine
driving. If you have done this and your vehicle still does
not pass the inspection for lack of OBD system
readiness, see your dealer or qualified service center to
prepare the vehicle for inspection.

2-101
Vehicle Information Menu (Base Audio System)
To access this menu using the base audio system, press
the up or down arrow on the INFO button located to the
right of the display.
The following items are available:

BLANK LINE

OUTSIDE TEMP

MI TRIP A*

MI TRIP B*

FUEL RANGE*

MPG AVG*

MPG INST
GAL FUEL USED*

AVG MPH*

TIMER*

BATTERY VOLTS

ENGINE OIL LIFE*

TRANS FLUID LIFE*
(Automatic Transmission Only)
*These items can be reset. Each one must be reset
individually. For a detailed description of the menu
items and how to reset them, see ªStatus Menu Item
Descriptionsº later in this section.
You can view any of these items at any time, but only
one item can be displayed at a time.

2-102
Vehicle Info (Information) Menu
(Navigation System)
To access the Vehicle Info menu using the Navigation
system, press the INFO button to the left of the screen.
You can also access this menu through the Setup menu.
See ªSetup Menuº in the Index of the Navigation
supplement.
The following submenu appears when Vehicle Info
is selected:

Outside Air Temperature

Trip Odometer A*

Trip Odometer B*

Fuel Range

Average Fuel Economy*

Instantaneous Fuel Economy

Fuel Used*
Average Vehicle Speed*

Timer*

Battery Voltage

Engine Oil Life*

Transmission Fluid Life*
(Automatic Transmission Only)

Blank Display
*These items can be reset. Each one must be reset
individually. For a detailed description of the menu
items and how to reset them, see ªStatus Menu Item
Descriptionsº following.
You can view any of these submenu items at any time by
selecting them using the TUNE/SEL knob. The
currently selected item is displayed at the top of the
screen. Only one item can be displayed at a time.

2-105
Battery Voltage/BATTERY VOLTS: If you select this
item, the current battery voltage is displayed. If the
voltage is in the normal range, the display will have OK
after it. For example, the display may read 13.2 Battery
Volts OK.
If there is a problem with the battery charging system,
there are four possible DIC messages that may be
displayed. See ªDriver Information Center (DIC)
Messagesº later in this section for more information.
Engine Oil Life/ENGINE OIL LIFE: If you select
this item, the percentage of remaining oil life is
displayed. If you see 99% Oil Life on the display, that
means that 99% of the current oil life remains.
When the oil life is depleted, the Change Engine Oil
message will appear on the display. You should change
the engine oil as soon as possible within 200 miles. Be
sure to keep a written record of the mileage and date of
the oil change so you will have it for future reference.
When you reset the Change Engine Oil message by
clearing it from the display, you still must reset the
engine oil life monitor separately. For more information
on resetting the engine oil life monitor, see ªOil Life
Monitor, How to Resetº in the Index.The engine oil life monitor does not check the amount
of oil your vehicle has, so you should check the oil level
periodically. See ªEngine Oilº in the Index for more
information.
Transmission Fluid Life/TRANS FLUID LIFE
(Automatic Transmission Only): If you select this
item, the percentage of remaining transmission fluid life
is displayed. If you see 99% Trans Fluid Life on the
display, that means that 99% of the current transmission
fluid life remains.
When the transmission fluid life is depleted, the Change
Transmission Fluid message will appear on the display.
You should change the engine oil as soon as possible
within 200 miles. Be sure to keep a written record of the
mileage and date of the oil change so you will have it
for future reference.
When you reset the Change Transmission Fluid message
by clearing it from the display, you still must reset the
transmission fluid life monitor separately. For more
information on resetting the engine oil life monitor, see
ªTransmission Fluid Life Monitor, How to Resetº in
the Index.

2-106
DIC Messages
These messages will appear if there is a problem sensed
in one of your vehicle's systems. The text messages are
the same for both the base audio and Navigation systems
unless otherwise indicated. The symbols, however,
appear only on the Navigation system display.
You must acknowledge a message to clear it from the
screen for further use. To clear a message, do one of the
following:

Using the Base audio system, press CLR.

Using the Navigation system, press the
multi
-function button next to the OK prompt.
Be sure to take any message that appears on the screen
seriously and remember that clearing the message will
only make the message disappear, not the problem.Battery Not Charging
This symbol appears
with the Battery Not
Charging message.
When this message appears on the display, there is a
problem with the generator and battery charging
systems. Have the electrical system checked by your
dealer as soon as possible.

2-107
Battery Saver Active
This symbol appears
with the Battery Saver
Active message.
This message appears when the system detects that the
battery voltage is dropping beyond a reasonable level.
The battery saver system will start reducing certain
features of the vehicle that you may not be able to
notice. At the point that the features are disabled, this
message is displayed. It means that the vehicle is trying
to save the charge in the battery.
Turn off all unnecessary accessories to allow the battery
to recharge.
The normal battery voltage range is 11.5 to 15.5 volts.
You can monitor battery voltage on the DIC by pressing
the INFO button until you find BATTERY VOLTS
(base audio system) or by selecting Battery Voltage
from the Vehicle Info menu (Navigation system).Battery Voltage HighThis symbol appears
with the Battery Voltage
High message.
This message indicates that the electrical charging
system is overcharging the battery. When the system
detects that the battery voltage is above approximately
16 volts, this message will be displayed.
To reduce the charging overload, use the vehicle's
accessories. Turn on the exterior lamps and radio, set the
climate control on AUTO and the fan speed on the
highest setting, and turn the rear window defogger on.
The normal battery voltage range is 11.5 to 15.5 volts
when the engine is running. You can monitor battery
voltage on the DIC by pressing the INFO button until
you find BATTERY VOLTS (base audio system) or by
selecting Battery Voltage from the Vehicle Info menu
(Navigation system).