steering CADILLAC CTS 2003 1.G User Guide

2-27
Retained Accessory Power (RAP)
The following accessories on your vehicle may be used
for up to 10 minutes after the ignition key is turned from
ON to OFF:

Radio

Power Windows

Audio Steering Wheel Controls (if programmed)

Sunroof (Option)
Power to these accessories stops after 10 minutes or
if a door is opened. If you want power for another
10 minutes, close all the doors and turn the ignition
key to ON and then back to OFF.
Starting Your Engine
Automatic Transmission
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle
is moving. If you do, you could damage the
transmission. Shift to PARK (P) only when
your vehicle is stopped.

2-38
Shift Speeds
CAUTION:
If you skip a gear when you downshift, you could
lose control of your vehicle. You could injure
yourself or others. Don't shift down more than
one gear at a time when you downshift.
NOTICE:
If you skip more than one gear when you
downshift, or if you race the engine when you
release the clutch pedal while downshifting, you
could damage the clutch or the transmission.
If the vehicle speed drops below 20 mph (32 km/h), or
if the engine is not running smoothly, you should
downshift to the next lower gear. You may have to
downshift two or more gears to keep the engine running
smoothly or for good performance.
Parking Brake
The parking brake pedal
is located on the lower
portion of the instrument
panel to the left of the
steering wheel.
To set the parking brake, hold the regular brake pedal
down with your right foot and push the parking brake
pedal down with your left foot.

2-39
To release the parking brake, pull the release lever
located to the left of the steering wheel on the
instrument panel.
If the ignition is on, the brake system warning light
on the instrument panel cluster should come on. If it
doesn't, you need to have your vehicle serviced. See
ªBrake System Warning Lightº in the Index for more
information.
NOTICE:
Do not drive your vehicle with the parking brake
on. Driving with the parking brake engaged can
cause your vehicle's rear brakes to overheat. You
may have to replace them, and you could also
damage other parts of your vehicle.
A warning chime will sound if the parking brake is set,
the ignition is on and the vehicle begins to move. To
stop the chime, fully release the parking brake.
If you are towing a trailer and parking on a hill, see
ªTowing a Trailerº in the Index for more information.

2-45
CAUTION:
It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don't leave your vehicle when the engine is
running unless you have to. If you've left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won't move, even when you're on fairly
level ground, always set your parking brake after
you move the shift lever to PARK (P).
Follow the proper steps to be sure your vehicle won't
move. See ªShifting Into PARK (P)º in the Index.
If you are parking on a hill and if you're pulling a
trailer, also see ªTowing a Trailerº in the Index.
Horn
Press on the pad near the horn symbols to sound
the horn.
Tilt Wheel
A tilt wheel allows you to adjust the steering wheel
before you drive. You can raise it to the highest level
to give your legs more room when you exit and enter
the vehicle.
The lever that allows you to tilt the steering wheel is
located on the left side of the steering column.
To tilt the wheel, hold the steering wheel and pull the
lever. Then move the steering wheel to a comfortable
position and release the lever to lock the wheel in place.

2-46
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane
-Change Signals

Headlamps

Headlamp High/Low Beam
-Changer

Flash
-To-Pass Feature

Fog Lamps
For more information on the exterior lamps, see
ªExterior Lampsº later in this section.
Turn and Lane-Change Signals
To signal a turn, move the lever all the way up or down.
The lever returns automatically when the turn is
complete.
Arrows on the instrument
panel cluster flash in the
direction of the turn or
lane change.
Raise or lower the lever until the arrow starts to flash to
signal a lane change. Hold it there until the lane change
is complete. The lever returns to its original position
when it's released.
Arrows that flash rapidly when signaling for a turn or
lane change may be caused by a burned
-out signal bulb.
Other driver's won't see the signal.
Replace burned
-out bulbs to help avoid possible
accidents. Check the fuse and for burned
-out bulbs if the
arrow fails to work when signaling a turn. See ªFuses
and Circuit Breakersº in the Index for more information.

2-49
Fog Lamps
Use the fog lamps for better vision in foggy or
misty conditions.
The fog lamp control is located on the turn
signal/multifunction lever to the left of the
steering column.The parking lamps must be on for the fog lamps
to work.
To turn the fog lamps on, turn the band on the lever up
to the fog lamp symbol and release it. The band will
return to its original position.
To turn the fog lamps off, turn the band up to the fog
lamp symbol and release it. The band will return to its
original position, and the fog lamps will turn off. If you
turn on the high
-beam headlamps, the fog lamps will
also turn off. They'll turn back on again when you
switch back to low
-beam headlamps.

2-50
Windshield Wipers
The lever on the right side of the steering column
operates the windshield wipers.
(Mist): Pull the lever down and release it for a
single wiping cycle. The lever will return to its original
position. For more cycles, hold the lever down before
releasing it.
(Off): Put the lever in this position to turn off the wipers.
(Delay): Put the lever in this position to set a delay
between wipes. Turn the delay adjustment band to set
the length of the delay.
(Delay Adjustment): Use this band to set the
length of the delay between wipes when using the delay
feature. The closer you move the band toward mist, the
longer the delay. The windshield wiper lever must be in
delay for this feature to work.
(Low Speed): Put the lever in this position for
slow, steady wiping cycles.
(High Speed): Put the lever in this position for
rapid wiping cycles.

2-53
Cruise Control
: On/Off
+: Resume/Accelerate, Set
-: Coast/Decelerate, Set
The buttons used to operate cruise control are located at
the bottom of the steering wheel.
With cruise control, you can maintain a speed of
approximately 25 mph (40 km/h) or more without
keeping your foot on the accelerator. This is helpful on
long trips. Cruise control does not work at speeds below
about 25 mph (40 km/h).When you apply your brakes, the cruise control
shuts off.
CAUTION:

Cruise control can be dangerous where you
can't drive safely at a steady speed. So,
don't use your cruise control on winding
roads or in heavy traffic.

Cruise control can be dangerous on
slippery roads. On such roads, fast changes
in tire traction can cause needless wheel
spinning, and you could lose control. Don't
use cruise control on slippery roads.
If your vehicle is in cruise control when the traction
control system begins to limit wheel spin, the cruise
control will automatically disengage. See ªTraction
Control Systemº and ªStabilitrak Systemº in the Index.
When road conditions allow you to safely use it again,
you may turn the cruise control back on.

2-56
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down. Applying the brake or shifting
into a lower gear will take you out of cruise control. If
you need to apply the brake or shift to a lower gear due
to the grade of the downhill slope, you may not want to
attempt to use your cruise control feature.Ending Cruise Control
To turn off the cruise control, step lightly on the brake
pedal, or press the cruise control on/off button on the
steering wheel.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Exterior Lamps
Headlamps
See ªTurn Signal/Multifunction Leverº listed previously
in this section for more information on the headlamps.

2-70
OnStar
System (If Equipped)
OnStar is a vehicle communications system that offers a
variety of services and provides a one
-touch hands-free
communication link between you and the OnStar Center.
To receive OnStar services, a service subscription
agreement is required and an additional fee may be
required. Services are available 24 hours a day, 7 days a
week. For more information, call 1
-888-ONSTAR-7
(1
-888-667-8277).
OnStar Services Button: Press this button once to
contact an advisor who will be able to assist you with
these services. If you are not quickly connected, the
system will automatically reset and redial. This ensures
connection to the center; there is no additional action
required. Press the Communication button to cancel the
automatic redial.
Emergency Button: In an emergency situation,
press the emergency service button. Upon receiving the
call, an advisor at the center will locate your vehicle and
assess the situation. If necessary, the advisor will alert
the nearest emergency service provider.
Communication Button: Press this button at
the end of a call. Also press this button to answer a
call from the center, or cancel a call if one of the other
buttons is accidentally pressed. This button is also used
to access OnStar Personal Calling and Virtual Advisor
services. See the OnStar owner package for more
information.
Volume Control: You can control the volume of the
OnStar System using the steering wheel controls.