CADILLAC CTS 2003 1.G Owners Manual

2-123
Starting Disabled -- Throttle Problem
This symbol appears
with the Starting
Disabled
-- Throttle
Problem message.
This message appears when your vehicle's throttle
system is not functioning properly. Have your vehicle
serviced at your dealership.
Theft Attempted
This symbol appears
with the Theft
Attempted message.
This message is displayed if the content theft
-deterrent
system has detected a break
-in attempt while you were
away from your vehicle.Top Speed
-- Fuel Cut Off
This symbol appears with
the Top Speed
-- Fuel Cut
Off message.
This message will appear when the Engine Control
Module (ECM) detects that the maximum speed for
your vehicle has been reached. Your vehicle's top speed
is based on the top speed rating of the tires. This ensures
that your vehicle stays in a safe operating range for
the tires.

2-124
Traction Engaged
This symbol appears
with the Traction
Engaged message.
This message will appear when the traction control
system is actively limiting wheel spin. Slippery road
conditions may exist if this message is displayed, so
adjust your driving accordingly. The message will stay
on for a few seconds after the traction control system
stops limiting wheel spin. See ªTraction Control
Systemº in the Index for more information.Traction SuspendedThis symbol appears
with the Traction
Suspended message.
This message will appear when the traction control
system has been temporarily shut off because your
vehicle's brakes have overheated. This message does not
indicate a problem with your vehicle's traction control
system. See ªTraction Control Systemº in the Index for
more information.

2-125
Trans (Transmission) Hot -- Idle Engine
This symbol appears
with the Trans Hot
--Idle
Engine message.
This message indicates that the transmission fluid in
your vehicle is too hot. Stop the vehicle and allow it to
idle until the transmission cools down or until this
message is removed.
Trunk Open
This symbol appears with
the Trunk Open message.
When this message appears on the display, it means that
the trunk lid of your vehicle was not closed completely.
You should make sure that the trunk lid is closed
completely.Turn Signal On
This symbol appears
with the Turn Signal
On message.
If you drive your vehicle for more than approximately
1 mile (1.6 km) with a turn signal on, this message
will appear as a reminder to turn off the turn signal.
A multiple chime will sound when this message is
displayed.

2-126
Accessing the DIC Main Menu
(Base Audio System)
There are two different procedures for accessing the
DIC main menu depending upon whether or not your
vehicle has the optional Navigation system.
To access the main menu of the DIC, do one of the
following:

Using the base audio system, press the TUNE/SEL
knob once. Turn the knob clockwise or
counterclockwise to scroll through the menu items.

Refer to the Navigation Supplement supplied with
your vehicle for more information on the accessing
DIC main menu and descriptions of the menu items
for the Navigation system.
DIC Main Menu
The DIC main menu for the base audio system consists
of the following menu items:


BASS - MID - TREBLE


EQ

DSP

AV C

H/A

AUTO STORE

PTY

TA

RDS MSG

AF

SEEK LOCAL/DISTANT

ENGLISH UNITS/METRIC UNITS

TCS

SET CLOCK

SETUP

2-127
DIC Main Menu Item Descriptions
(Base Audio System)
The following descriptions are for the base audio
system. For information pertaining to the Navigation
audio system, see ªAudio Systemº in the Index of the
Navigation Supplement supplied with your vehicle.
BASS - MID (Midrange) - TREBLE: This
menu item allows you to adjust the levels for the bass,
midrange, treble, balance, and fader features of the
audio system. For more information, see ªAudio
Systemsº in the Index.
EQ (Equalizer): This menu item allows you to
choose among five preset equalizations for the audio
system. See ªEqualizerº in the Index for more
information.
DSP (Digital Signal Processing): This menu item
allows you to select the DSP type that you want on the
audio system. You may choose Normal, Talk, Spacious,
Rear Seat or Driver Seat. Press the TUNE/SEL knob to
scroll through these choices. Once the desired choice is
displayed, turn the knob to set your DSP choice and
continue scrolling through the main menu.
See ªDSPº in the Index for more information.AVC (Automatic Volume Compensation): This menu
item allows you to turn the AVC feature on and off.
Press the TUNE/SEL knob once to turn AVC on and off.
When AVC is on, an X will be in the box next to AVC
on the menu. The X disappears when AVC is off.
See ªAVCº in the Index for more information.
H/A (Home/Away Preset Stations): This menu item
allows you to switch back and forth between your home
and away preset radio stations. Press the TUNE/SEL
knob to switch between home and away.
See ªHome and Away Preset Stationsº in the Index for
more information.
AUTOSTORE: This menu item allows you to
automatically store radio stations with the strongest
signals as presets. See ªAudio Systemsº in the Index for
more information.
PTY (Program
-Type Mode): This menu item allows
you to select radio stations based on preset
program
-types. To turn the PTY feature on, press the
TUNE/SEL knob once. When PTY is on, an X will be in
the box next to PTY on the menu. The X disappears
when PTY is off.
See ªAudio Systemsº in the Index for more information.

2-128
TA (Traffic Announcement): This menu item allows
you to turn the TA feature on and off. To turn the TA
feature on, press the TUNE/SEL knob once. When TA
is on, an X will be in the box next to TA on the menu.
The X disappears when TA is off.
See ªRDS Messagesº in the Index for more information.
RDS (Radio Data System) MSG (Message): This
menu item allows you to view an RDS radio station
message broadcast by a radio station. To view the
message, press the TUNE/SEL knob once. The message
will appear on the screen.
See ªRDS Messagesº in the Index for more information.
AF (Alternate Frequency): This menu item allows you
to turn the AF feature on and off. To turn on AF, press
the TUNE/SEL knob once. When AF is on, an X will be
in the box next to TA on the menu. The X disappears
when AF is off.
See ªUsing RDSº in the Index for more information.
SEEK LOCAL/DISTANT: This feature instructs the
audio system to seek only local radio stations with the
strongest signal or to seek all radio stations with a strong
signal in a large area. Use LOCAL when you are in
urban areas where there are several strong radio station
signals and you want to limit the number of stations tothose with the strongest signals only. Use DISTANT
when you are in rural areas where there are fewer radio
station signals available.
To switch between LOCAL and DISTANT, press the
TUNE/SEL knob. Your choice will be set when you
press BACK and return to the main menu.
English/Metric Units
Use this menu item to adjust
the measurement units.
You can choose between ENGLISH UNITS and
METRIC UNITS. To switch between the two, press the
TUNE/SEL knob. Once your choice is displayed, turn
the knob to set your choice and continue scrolling
through the main menu.
The measurement units that you choose will be reflected
on all the vehicle system displays, not just the DIC
information. For example, the climate control panel will
display degrees Celsius if you choose METRIC UNITS.

2-129
TCS (Traction Control System): You can enable
or disable the traction control system using this menu
item. Press the TUNE/SEL knob to switch between on
and off.
You can also turn the traction control system off using
the traction control button located in the glove box or
by programming one of the steering wheel controls
(1, 2, 3 or 4) or audio system softkeys to enable/disable
the TCS. See ªReconfigurable Steering Wheel Controlsº
and ªConfigurable Radio Display Keysº in the Index for
more information.
When you disable the traction control system, the
Traction Suspended message will appear on the DIC and
the traction control system warning light on the
instrument panel cluster will come on. See ªDriver
Information (DIC) Messagesº and ªTraction Control
System Warning Lightº listed previously in this section
for more information.SET CLOCK
Use this menu item to
set the time on the
vehicle's clock.
See ªSetting the Clockº in the Index for more
information.
SETUP: When you select this menu item, the following
submenu is available:

Personalization

Configure Display Keys

Configure SWC (Steering Wheel Control) Keys

Clear Tape Hours
You can use the items on this submenu to customize
your vehicle's audio system and optional memory
features. See ªVehicle Programming and Personalization
Features,º ªReconfigurable Steering Wheel Controlsº
and ªCare of Your Cassette Tape Playerº in the Index for
more information on these menu items.

2-130
Vehicle Programming and
Personalization Features
Your vehicle is equipped with personalization that
allows you to program certain features to a preferred
setting for up to two people. The number of
programmable features varies depending upon which
model of the vehicle is purchased.
On all vehicles, features such as climate control settings,
radio preset settings, exterior lighting at unlock, remote
lock and unlock confirmation, and automatic door locks
have already been programmed for your convenience.
Some vehicles are equipped with additional features that
can be programmed including the seat and outside
rearview mirror position. The optional navigation
system screen preferences will remain at the last set
position.
If your vehicle is equipped with the ability to program
additional personalization features, the driver's
preferences are recalled by pressing the unlock button
on the remote keyless entry transmitter, 1 or 2, or
by pressing the appropriate memory button, 1 or 2,
located on the driver's door. Certain features can be
programmed not to recall until the key is placed in the
ignition. To change feature preferences you must use
one of the following procedures.
Entering the Personalization Menu
To enter the feature programming mode, use one of the
following procedures:
Base Audio System
1. Turn the ignition to ON, but do not start the engine.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on the driver's
door armrest. The DIC display will show either Driver 1
or 2 depending on which button was selected.
3. Press the TUNE/SEL knob once to access the main
menu of the DIC.
4. Turn the TUNE/SEL knob until SETUP is highlighted.
5. Press the TUNE/SEL knob once to access the
SETUP menu.
6. Scroll to the feature you want to change, and press
the TUNE/SEL knob to turn the feature on or off.
If the feature is turned on, a check mark will appear
next to the feature name.
If none of the personalization items are turned on,
turn on the personalization menu by pressing the
TUNE/SEL knob. The list of features will then
appear, and you can repeat Step 6.

2-131
Navigation System
1. Turn the ignition to ON without the engine running.
Make sure an automatic transmission is in PARK (P)
or a manual transmission has the parking brake set.
2. Turn on the Navigation/audio system by pressing the
PWR/VOL knob located to the lower left of the
display once.
3. Access the DIC main menu by pressing the MAIN
button located to the lower left of the display.
4. Press the multi
-function button next to Feat Prog to
access the Feature Programming menu.
5. Press the TUNE/SEL knob to turn on the
Personalization features. An X will appear in the box
to the left when Personalization is turned on.
Personalization Features
The following choices are available for programming
using both the Base audio and Navigation systems
unless otherwise indicated.
Personalization Name
This feature allows you to type in a name that will
appear on the DIC display whenever the corresponding
remote keyless entry transmitter is used or one of the
buttons on the driver's door armrest (1 or 2) is pressed.
If a customized name is not programmed, the system
will show Driver 1 or Driver 2 to correspond with the
numbers on the back of the remote keyless entry
transmitters.
To program a name, use one of the following
procedures:

2-132
To customize the name using the Base audio system, do
the following:
1. Select the PERSONALIZATION NAME menu item
by pressing the TUNE/SEL knob once.
You will see a cursor on the screen.
2. Turn the TUNE/SEL knob until you reach the first
letter you want to highlight it. There is a complete
alphabet with both upper and lower case letters and
the numbers zero through nine. Also included are
spaces and other non
-letter characters such as the
ampersand (&).
3. Press the TUNE/SEL knob once to select the letter.
The letter will then appear on the display.
If you make a mistake, press the Back key. This will
exit the menu. You can then go back into the menu
and edit the name. You can also press the TUNE/SEL
knob repeatedly to cycle through all the characters
until you reach the character you wish to change.
4. Repeat Steps 2 and 3 until the name you want is
complete. You can program up to 16 characters.
5. Press the BACK button located to the lower right of
the display to exit and set your choice or let the
screen time out and return to the main screen.To customize the name using the Navigation system, do
the following:
1. Press the multi
-function button located to the right of
the display that is next to the EDIT prompt.
This will open the EDIT menu. You will see an alphabet
at the bottom of the display and a blank line with a
blinking cursor. Also included here are spaces and other
non
-letter characters such as the ampersand (&).
2. Scroll to the first letter you want to highlight it.
3. Press the TUNE/SEL knob once to select the letter.
The letter will then appear on the line above the alphabet.
4. Repeat Steps 2 and 3 until the name you want is
complete. You can program up to 26 characters.
If you make a mistake, press the multi
-function
button located to the right of the display that is next
to the Delete prompt. This will delete the last letter
you typed so you can input a different letter.
5. Press the multi
-function button located to the right of
the display that is next to the Back prompt to exit
and set your choice.
The name you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.