light CADILLAC CTS 2003 1.G Repair Manual

2-134
Remote Exit Recall (If Equipped)
This feature allows any previously programmed exit
position for the driver's seat to be recalled when the
unlock button on the remote keyless entry transmitter is
pressed.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to REMOTE EXIT RECALL to highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Remote Exit Recall and press the knob once
to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Recall Memory/Recall Driving Positions was
turned on previously, selecting Remote Exit Recall will
override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-135
Key in Recall Memory (If Equipped)
This feature recalls any previously programmed seat
and mirror positions when the key is inserted into the
ignition.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to KEY IN RECALL MEMORY to
highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Key In Recall Memory and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Remote Recall Memory/Recall Driving Positions was
turned on previously, selecting Key In Recall Memory
will override that choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-136
Auto Exit Seat (If Equipped)
This feature allows any previously programmed exit
position for the driver's seat to be recalled when the key
is removed from the ignition.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to AUTO EXIT SEAT using the TUNE/SEL
knob to highlight it.3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, an check mark will
appear in the box next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Auto Exit Seat using the TUNE/SEL knob
to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-137
Twilight Delay
This feature allows you to set the amount of time you
want the exterior lamps to remain on after you exit the
vehicle.
Programmable Modes
Mode 1: 0:00 seconds
Mode 2: 0:15 seconds
Mode 3: 0:30 seconds
Mode 4: 1:00 minute
Mode 5: 1:30 minutes
Mode 6: 2:00 minutes
Mode 7: 2:30 minutes
Mode 8: 3:00 minutes
Before your vehicle was shipped from the factory, it was
programmed with this feature turned off. This may have
been changed since the vehicle left the factory. To
determine the mode to which the vehicle is programmed
or to program the vehicle to a different mode, use one of
the following procedures:To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to TWILIGHT DELAY using the TUNE/SEL
knob to highlight it.
3. Press the TUNE/SEL knob to turn Twilight Delay on
or off. If the feature is turned off, the exterior lamps
will not illuminate at all when you exit the vehicle.
Once the feature is turned on, the modes listed above
will appear on the display, and the currently selected
time delay will have a check mark next to it.
4. Turn the TUNE/SEL knob until you reach the
desired time delay.
5. Press the TUNE/SEL knob once to select
your choice.
When a time is selected, a check mark will appear
next to the time delay you chose. Only one mode
can be selected at a time.

2-138
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Twilight Delay using the TUNE/SEL knob
to highlight it.
3. Press the TUNE/SEL knob to turn Twilight Delay on
or off. If the feature is turned off, the exterior lamps
will not illuminate at all when you exit the vehicle.
Once the feature is turned on, the modes listed above
will appear on the display, and the currently selected
time delay will have an X in the box to the left.
4. Turn the TUNE/SEL knob until you reach the
desired time delay.
5. Press the TUNE/SEL knob once to select
your choice.
When a time is selected, an X will appear next to the
time delay you chose. Only one mode can be
selected at a time.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Lights Flash at Unlock
This feature turns on the exterior lamps when the remote
keyless entry transmitter is used to unlock the vehicle.
The lamps will remain on for approximately 20 seconds
unless a door is opened, the ignition is turned to
ACCESSORY, ON or START or the remote keyless
entry transmitter is used to lock the vehicle.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to LIGHTS FLASH AT UNLOCK to
highlight it.

2-139
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Lights Flash At Unlock and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Lights Flash at Lock
This feature allows the exterior lamps to flash once
when the remote keyless entry transmitter is used to lock
the vehicle. All doors must be closed for this feature to
work, and the lamps will not flash if the parking lamps
or headlamps are on.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to LIGHTS FLASH AT LOCK to highlight it.

2-140
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Lights Flash At Lock and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Horn Sounds At Lock was previously turned on,
selecting Lights Flash At Lock will override the
previous choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Horn Sounds at Lock
This feature sounds the horn once when the remote
keyless entry transmitter is used to lock the vehicle.
All doors must be closed for this feature to work.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to HORN SOUNDS AT LOCK to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.

2-141
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Horn Sounds At Lock and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
If Lights Flash At Lock was previously turned on,
selecting Horn Sounds At Lock will override the
previous choice.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Exterior Lights at Unlock
This feature turns on the exterior lamps when the remote
keyless entry transmitter is used to unlock the vehicle.
The lamps will remain on for about 20 seconds unless a
door is opened, the ignition is turned to ACCESSORY,
ON or START or the remote keyless entry transmitter is
used to lock the vehicle.
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:

2-142
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to EXT. LIGHT AT UNLOCK to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Remote Keyless Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Exterior Lights At Unlock and press the
knob once to select it.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Doors Lock in Gear (Automatic Transmission Only)
With the ignition in ON and all the doors closed, this
feature allows the vehicle's doors to automatically lock
when the driver shifts the transmission out of PARK (P).
Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do the
following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to DOORS LOCK IN GEAR to highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.

2-143
To change the mode using the Navigation system, do the
following:
1. Enter the Personalization menu following the
instructions listed previously.
2. Scroll to Door Lock Options to highlight it.
3. Press the TUNE/SEL knob to view the modes.
4. Scroll to Doors Lock In Gear and press the knob
once to select it.
When the mode is turned on, an X will appear in the
box to the left.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
Automatic Door Lock (Manual Transmission Only)
This feature allows the vehicle's doors to automatically
lock when the vehicle speed surpasses 5 mph (8 km/h).Programmable Modes
Mode 1: ON
Mode 2: OFF
Before your vehicle was shipped from the factory, it was
programmed to Mode 1. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, use one of the following procedures:
To change the mode using the Base audio system, do
the following:
1. Enter the personalization portion of the SETUP
menu following the instructions listed previously.
2. Scroll to AUTOMATIC DOOR LOCK to
highlight it.
3. Press the TUNE/SEL knob to switch back and forth
between on and off.
When the mode is turned on, a check mark will
appear next to the feature name.