service CADILLAC CTS 2007 1.G Owner's Manual

Brake System Warning Light
Your vehicle’s hydraulic brake system is divided
into two parts. If one part is not working, the other
part can still work and stop you. For good
braking, though, you need both parts working well.
If the warning light comes on, there is a brake
problem. Have your brake system inspected
right away.
This light should come on briey when you turn
the ignition key to ON. If it does not come on then,
have it xed so it will be ready to warn you if
there is a problem.When the ignition is on, the brake system warning
light will also come on when you set your
parking brake. The light will stay on if your parking
brake does not release fully. If it stays on after
your parking brake is fully released, it means you
have a brake problem.
If the light comes on while you are driving, pull off
the road and stop carefully. You may notice
that the pedal is harder to push, or the pedal may
go closer to the oor. It may take longer to
stop. If the light is still on, have the vehicle towed
for service. SeeTowing Your Vehicle on
page 326.
{CAUTION:
Your brake system may not be working
properly if the brake system warning light
is on. Driving with the brake system
warning light on can lead to an accident.
If the light is still on after you have pulled
off the road and stopped carefully, have
the vehicle towed for service.
United StatesCanada
205

Anti-Lock Brake System
Warning Light
With the Anti-Lock
Brake System (ABS),
the light will come
on when your engine is
started and stay on
for several seconds.
This is normal.
If the ABS warning light comes on and stays on,
there may be a problem with the anti-lock
portion of the brake system. If the brake system
warning light is not on, you still have brakes,
but you do not have anti-lock brakes. SeeBrake
System Warning Light on page 205for more
information.
If the light stays on, turn the ignition to OFF. If the
light comes on when you are driving, stop as
soon as possible and turn the ignition off. Then
start the engine again to reset the system. If
the light still stays on, or comes on again while
you are driving, your vehicle needs service.If the regular brake system warning light is not on,
you still have brakes, but you do not have
anti-lock brakes. If the regular brake system
warning light is also on, you do not have anti-lock
brakes and there is a problem with your regular
brakes. SeeBrake System Warning Light on
page 205for more information.
The ABS warning light should come on briey
when you turn the ignition key to ON. If the light
does not come on then, have it xed so it will
be ready to warn you if there is a problem.
Traction Control System (TCS)
Warning Light
If the TC (traction
control) warning light
comes on and stays on,
there may be a
problem with the traction
control system.
206

The TC warning light will come on briey when
you turn the ignition to ON. If it does not come on
then, have it xed so it will be ready to warn
you if there is a problem.
The light will also come on if you turn the traction
control system off using the TC on/off button
located in the glove box for the CTS and on the
steering wheel for the CTS-V.
If the TC warning light stays on or comes on while
you are driving, pull off the road as soon as
possible and stop carefully. Try resetting the
system by turning the ignition off then back on.
If the light still stays on or comes back on
again while you are driving, your vehicle needs
service. Have the Traction Control System (TCS)
inspected as soon as possible. SeeTraction
Control System (TCS) (CTS) on page 293
orTraction Control System (TCS) (CTS-V) on
page 295for more information.Engine Coolant Temperature
Warning Light (CTS)
This light will come on
when you rst start the
vehicle as a check
to let you know that the
light is working.
It will go out after a few seconds. If the light does
not come on, see your dealer.
If the light does not go out or if the light comes on
and stays on while you are driving, your vehicle
may have a problem with the cooling system. You
should stop the vehicle and turn off the engine
as soon as possible to avoid damage to the
engine. A warning chime will also sound when this
light is on.
SeeEngine Overheating on page 360for more
information.
207

Malfunction Indicator Lamp
Check Engine Light
Your vehicle has a
computer which
monitors operation of
the fuel, ignition,
and emission control
systems.
This system is called OBD II (On-Board
Diagnostics-Second Generation) and is intended
to assure that emissions are at acceptable
levels for the life of the vehicle, helping to produce
a cleaner environment. The check engine light
comes on to indicate that there is a problem and
service is required. Malfunctions often will be
indicated by the system before any problem is
apparent. This may prevent more serious damage
to your vehicle. This system is also designed to
assist your service technician in correctly
diagnosing any malfunction.Notice:If you keep driving your vehicle with
this light on, after awhile, the emission controls
might not work as well, your vehicle’s fuel
economy might not be as good, and the engine
might not run as smoothly. This could lead
to costly repairs that might not be covered by
your warranty.
Notice:Modications made to the engine,
transmission, exhaust, intake, or fuel system
of your vehicle or the replacement of the
original tires with other than those of the same
Tire Performance Criteria (TPC) can affect
your vehicle’s emission controls and can cause
this light to come on. Modications to these
systems could lead to costly repairs not
covered by your warranty. This could also
result in a failure to pass a required Emission
Inspection/Maintenance test. SeeAccessories
and Modifications on page 332.
209

This light should come on, as a check to show
you it is working, when the ignition is on and the
engine is not running. If the light does not
come on, have it repaired. This light will also
come on during a malfunction in one of two ways:
Light Flashing— A misre condition has
been detected. A misre increases vehicle
emissions and may damage the emission
control system on your vehicle. Diagnosis and
service may be required.
Light On Steady— An emission control
system malfunction has been detected on your
vehicle. Diagnosis and service may be
required.
If the Light is Flashing
The following may prevent more serious damage
to your vehicle:
Reducing vehicle speed
Avoiding hard accelerations
Avoiding steep uphill grades
If you are towing a trailer, reduce the amount
of cargo being hauled as soon as it is
possibleIf the light stops ashing and remains on steady,
see “If the Light Is On Steady” following.
If the light continues to ash, when it is safe to do
so, stop the vehicle. Find a safe place to park
your vehicle. Turn the key off, wait at least
10 seconds and restart the engine. If the light
remains on steady, see “If the Light Is On Steady”
following. If the light is still ashing, follow the
previous steps, and see your dealer for service as
soon as possible.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. SeeFilling the Tank on page 337.
The diagnostic system can determine if the
fuel cap has been left off or improperly installed. A
loose or missing fuel cap will allow fuel to
evaporate into the atmosphere. A few driving trips
with the cap properly installed should turn the
light off.
210

Oil Pressure Light
{CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches re. You or others could
be burned. Check your oil as soon as
possible and have your vehicle serviced.
Notice:Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.If your vehicle has this
light, it will come on
when there is a problem
with your engine oil
pressure.
This light will come on when you turn your key to
ON or START. It goes off once you start the
engine. That is a check to be sure the light works.
If it does not come on, be sure to have it xed
so it will be there to warn you if there is a problem.
When the light comes on and stays on, it means
that oil is not owing through your engine properly.
You could be low on oil and you might have
some other system problem. SeeEngine Oil on
page 346for more information.
212

Sport Mode Light
(Automatic Transmission/CTS)
This light will come on
while the sport mode is
in use.
When you turn off the sport mode, the light will go
out. If it stays on, your vehicle may need service.
See your dealer. See “Sport Mode” under
Automatic Transmission Operation on page 122
for more information.
Security Light
For information
regarding this light, see
Theft-Deterrent
System on page 111.
Fog Lamp Light
This light will come on
when the fog lamps are
in use.
The light will go out when the fog lamps are
turned off. SeeFog Lamps on page 183for more
information.
Lights On Reminder
This light comes on
whenever the parking
lamps are on.
SeeHeadlamps on Reminder on page 181for
more information.
213

Transmission Fluid Hot Message
When you see this
ashing symbol, the
transmission uid
temperature is high
(290°F (143°C)).
To acknowledge this warning, press either button
on the outboard switch on the left spoke of the
steering wheel. After you press this button, the
warning will redisplay every 10 minutes until the
temperature returns to the normal operating range.
If this message appears, you may continue to drive
at a slower speed while monitoring the transmission
uid temperature. Ideally, the transmission oil
temperature should not rise above 265°F (129°C). If
you regularly experience temperatures above this
limit due to high performance operation, it is
recommended to use an auxiliary uid cooler for the
transmission and differential. See your dealer for
details. If this warning is displayed during normal
vehicle operation on at roads, your vehicle may
need service. See your dealer for an inspection.
SeeDIC Warnings and Messages on page 232and
Manual Transmission Fluid on page 354for more
information.
Hot Coolant Temperature Warning
Message
When you see this
ashing symbol, the
engine coolant
temperature is high
(257°F (125°C)).
To acknowledge this warning, press either button
on the outboard switch on the left spoke of the
steering wheel. After you press a button, this
warning will come on every 10 minutes until the
temperature returns to the normal operating range.
Driving aggressively or driving on long hills can
cause the engine coolant temperature to be higher
than normal. The Engine Coolant Temperature
Warning Light should also come on. SeeEngine
Coolant Temperature Warning Light (CTS) on
page 207for more information. If this warning is
displayed during normal vehicle operation on
at roads, your vehicle may need service.
See your dealer for an inspection.
219

Check Engine Oil Pressure Message
Your vehicle may have
this feature. When you
see this ashing
symbol, the engine oil
pressure is low.
To acknowledge this warning, press either button
on the outboard switch on the left spoke of the
steering wheel. After you press this button,
the warning will redisplay every 10 minutes until
the pressure returns to the normal operating
range. Oil pressure should be 20 to 80 psi
(140 to 550 kPa). In certain situations such as
long, extended idles on hot days, it could read as
low as 6 psi (40 kPa) and still be considered
normal. It may vary with engine speed, outside
temperature and oil viscosity. The Oil Pressure
Light should also come on. SeeOil Pressure Light
on page 212for more information.
Oil Temperature Warning Message
When you see this
ashing symbol, the
engine oil temperature
is high.
To acknowledge this warning, press either button
on the outboard switch on the left spoke of the
steering wheel. After you press a button, the
warning will come on every 10 minutes until the
temperature returns to the normal operating range.
Driving aggressively or driving on long hills can
cause the engine oil temperature to be higher than
normal. If this warning is displayed during
normal vehicle operation on at roads, your vehicle
may need service. See your dealer for an
inspection. SeeEngine Oil on page 346for more
information.
220

When the oil life is depleted, the Change Engine
Oil message will appear on the display. See
your dealer for service. In addition to the engine
oil life system monitoring the oil life, additional
maintenance is recommended in the Maintenance
Schedule in this manual. SeeScheduled
Maintenance on page 462andEngine Oil on
page 346for more information.
When you reset the Change Engine Oil message
by clearing it from the display, you still must reset
the engine oil life system separately. For more
information on resetting the engine oil life system,
see “How to Reset the Engine Oil Life System
and the Oil Life Indicator” underEngine Oil
Life System on page 349. If you clear the Change
Engine Oil message from the display, it will not
re-appear.
TRANS FLUID LIFE (Automatic Transmission):
If you select this item, the percentage of
remaining transmission uid life is displayed.
If you see 99% TRANS FLUID LIFE on the display,
that means that 99% of the current transmission
uid life remains.When the transmission uid life is depleted, the
Change Trans Fluid message will appear on
the display. You should change the transmission
uid as soon as possible. Be sure to keep a written
record of the mileage and date of the uid
change so you will have it for future reference.
SeeScheduled Maintenance on page 462
andRecommended Fluids and Lubricants on
page 473for more information.
When you reset the Change Trans Fluid message
by clearing it from the display, you still must
reset the transmission uid life monitor separately.
For more information on resetting the transmission
uid life monitor, seeAutomatic Transmission
Fluid on page 353.
LF TIRE:If you select this item, the driver’s side
front tire pressure will be displayed. If the tire
pressure is low, LOW will be displayed with this
item. The pressure can be displayed in pounds per
square inch (PSI) or kilopascals (KPA). To change
the units, seeDIC Main Menu on page 228
DIC Main Menu.
227