brake light CADILLAC CTS 2009 2.G Owners Manual

Vehicle Symbol Chart
Here are some additional symbols that may be found on
the vehicle and what they mean. For more information
on the symbol, refer to the index.
9:Airbag Readiness Light
#:Air Conditioning
!:Antilock Brake System (ABS)
g:Audio Steering Wheel Controls or OnStar®
$:Brake System Warning Light
":Charging System
I:Cruise Control
B:Engine Coolant Temperature
O:Exterior Lamps
#:Fog Lamps
.:Fuel Gage
+:Fuses
i:Headlamp High/Low-Beam Changer
j:LATCH System Child Restraints
*:Malfunction Indicator Lamp
::Oil Pressure
}:Power
/:Remote Vehicle Start
>:Safety Belt Reminders
7:Tire Pressure Monitor
F:Traction Control
M:Windshield Washer Fluid
v

Up-Shift Light
CTS vehicles with a manual
transmission have an
economy up-shift light on
the instrument panel. This
light shows when to shift to
the next higher gear for the
best fuel economy.
When this light comes on, you can shift to the next
higher gear if weather, road, and traffic conditions allow.
For the best fuel economy, accelerate slowly and
shift when the light comes on.
While you accelerate, it is normal for the light to go on
and off if you quickly change the position of the
accelerator. Ignore the light when you downshift.
CTS-V vehicles use tracer lights around the outside of
the tachometer as a performance up-shift light.
These tracers ash to indicate when to shift to the next
higher gear to avoid the engine speed limit. See
Tachometer on page 3-34for more information.
Skip Shift (CTS-V)
Under light acceleration, the transmission will only
allow you to shift from 1 (First) to 4 (Fourth). Shifts from
1 (First) to 2 (Second) or 3 (Third) are not allowed.
This helps improve fuel mileage.
Under harder acceleration, Skip Shift is disabled, and
the driver has all gears available.
Parking Brake
The parking brake pedal is
located on the lower portion
of the instrument panel to
the left of the steering
wheel.
To set the parking brake, hold the brake pedal down,
then push the parking brake pedal down.
2-42

If the ignition is on, the brake system warning light on the
instrument panel cluster should come on. If it does not,
you need to have the vehicle serviced. SeeBrake System
Warning Light on page 3-39for more information.
To release the parking brake, pull the release lever
located to the left of the steering wheel on the instrument
panel.Notice:Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Make sure
that the parking brake is fully released and the brake
warning light is off before driving.
A warning chime will sound if the parking brake is set,
the ignition is on, and the vehicle begins to move.
To stop the chime, fully release the parking brake.
If you are towing a trailer and parking on a hill,
seeTowing a Trailer (CTS-V) on page 4-27orTowing a
Trailer (CTS) on page 4-28for more information.
2-43

Electric Parking Brake
{CAUTION:
On vehicles with a manual transmission, releasing
the clutch and pressing the accelerator will release
the Electric Parking Brake. If the vehicle is not in a
gear, the vehicle could move, and you or others
could be injured. Make sure the vehicle is in a
gear before attempting to drive away. To avoid
unexpected vehicle movement, do not partially
release the clutch or press the accelerator pedal
until you are ready to release the parking brake
and drive away.Vehicles with
the Electric
Parking Brake
(EPB) have
a switch in the
center console.
The EPB takes the place of the manual parking brake
system, the foot pedal and release handle. The system
has two warning lights and ve Driver Information Center
(DIC) messages. SeeBrake System Warning Light on
page 3-39andDIC Warnings and Messages on
page 3-58for more information. In case of insufficient
electrical power, the EPB cannot be applied or released.
2-44

EPB Apply
The EPB can be applied any time the vehicle is stopped.
The EPB is applied by momentarily lifting up on the EPB
switch. Once fully applied, the BRAKE light will be on,
and the DIC message “Park Brake Set” will be displayed.
If the light does not come on, or is ashing, you need to
have the vehicle serviced. Do not drive the vehicle if
the BRAKE light is ashing. See your dealer/retailer.
SeeBrake System Warning Light on page 3-39for more
information.
If the EPB is applied while the vehicle is in motion,
a chime will sound, and the DIC message “Release
Park Brake Switch” will be displayed. The vehicle
will decelerate as long as the switch is held in the
up position. Releasing the EPB switch during the
deceleration will release the parking brake. If the
switch is held in the up position until the vehicle
comes to a stop, the EPB will remain applied.
If the BRAKE light is on, either the EPB is applied, or
there is a failure in the hydraulic brake system.If this light is ashing, the EPB is only partially applied
or released, or there is a problem with the EPB.
The DIC message “Service Park Brake” will be
displayed. If this light is ashing, release the EPB, and
attempt to apply it again. If this light continues to
ash, do not drive the vehicle. See your dealer/retailer.
If the
Ylight is on, the EPB has detected an error
in another system and is operating with reduced
functionality. To apply the EPB when this light is on, lift up
on the EPB switch and hold it in the up position. Full
application of the parking brake by the EPB system may
take a longer period of time than normal when this light is
on. Continue to hold the switch until the BRAKE light
remains on. If the
Ylight is on, see your dealer/retailer.
If the EPB fails to apply, the rear wheels should be
blocked to prevent vehicle movement.
2-45

EPB Release
To release the EPB, turn the ignition switch to the
ON/RUN position, apply and hold the brake pedal, and
push down momentarily on the EPB switch. If you attempt
to release the EPB without the brake pedal applied, a
chime will sound, and the DIC message “Press Brake
Pedal to Release Park Brake” will be displayed. The EPB
is released when the BRAKE light is off and the DIC
message “Park Brake Released” is displayed.
If the
Ylight is on, the EPB has detected an error
in another system and is operating with reduced
functionality. To release the EPB when this light is on,
push down on the EPB switch and hold it in the down
position. EPB release may take a longer period of time
than normal when this light is on. Continue to hold the
switch until the BRAKE light is off. If the
Ylight is on,
see your dealer/retailer.
Notice:Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Make sure
that the parking brake is fully released and the brake
warning light is off before driving.
Automatic EPB Release
The EPB will automatically release if the vehicle is
running, placed into gear and an attempt is made to
drive away. Avoid rapid acceleration when the EPB
is applied, to preserve park brake lining life.
The EPB can also be used to prevent roll back for
vehicles with a manual transmission taking off on a hill.
In a situation where no roll back is desired, an applied
EPB will allow both feet to be used for the clutch
and accelerator pedals in preparation for starting the
vehicle moving in the intended direction.
In this situation, perform the normal clutch and
accelerator actions required to begin moving the vehicle.
There is no need to push the switch to release the EPB.
If you are towing a trailer and parking on a hill, see
Towing a Trailer (CTS-V) on page 4-27orTowing
a Trailer (CTS) on page 4-28for more information.
2-46

When the System Does Not Seem to
Work Properly
If the URPA system will not activate due to a temporary
condition, the message PARK ASSIST OFF will be
displayed on the DIC and a red light will be shown on
the rear URPA display when the shift lever is moved into
R (Reverse). This occurs under the following conditions:
The driver disables the system.
The ultrasonic sensors are not clean. Keep the
vehicle’s rear bumper free of mud, dirt, snow,
ice and slush. For cleaning instructions, see
Washing Your Vehicle on page 5-110.
A trailer was attached to the vehicle, or a bicycle or
an object was hanging out of the trunk during the
last drive cycle, the red light may illuminate in
the rear display. Once the attached object is
removed, URPA will return to normal operation.
A tow bar is attached to the vehicle.
The vehicle’s bumper is damaged. Take the vehicle
to your dealer/retailer to repair the system.
Other conditions may affect system performance,
such as vibrations from a jackhammer or the
compression of air brakes on a very large truck.
If the system is still disabled after driving forward at least
15 mph (25 km/h), take the vehicle to your dealer/retailer.
OnStar®System
OnStar uses several innovative technologies and live
advisors to provide a wide range of safety, security,
information, and convenience services. If the airbags
deploy, the system is designed to make an automatic
call to OnStar Emergency advisors who can request
emergency services be sent to your location. If the keys
are locked in the vehicle, call OnStar at 1-888-4-ONSTAR
to have a signal sent to unlock the doors. OnStar
Hands-Free Calling, including 30 trial minutes good
for 60 days, is available on most vehicles. OnStar
Turn-by-Turn Navigation service, with one trial route, is
available on most vehicles. Press the OnStar button to
have an OnStar advisor contact Roadside Service.
OnStar service is provided subject to the OnStar Terms
and Conditions included in the OnStar Subscriber glove
box literature.
2-56

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-6
Horn .............................................................3-6
Tilt and Telescopic Steering Wheel...................3-6
Power Tilt Wheel and Telescopic Steering
Column......................................................3-7
Turn Signal/Multifunction Lever.........................3-7
Turn and Lane-Change Signals........................3-8
Headlamp High/Low-Beam Changer..................3-8
Flash-to-Pass.................................................3-9
Windshield Wipers..........................................3-9
Rainsense™ Wipers......................................3-10
Windshield Washer.......................................3-12
Headlamp Washer........................................3-13
Cruise Control..............................................3-14
Headlamps..................................................3-17
Wiper Activated Headlamps............................3-17
Headlamps on Reminder................................3-17
Daytime Running Lamps (DRL).......................3-18
Adaptive Forward Lighting System...................3-19
Fog Lamps ..................................................3-19
Exterior Lighting Battery Saver........................3-20
Instrument Panel Brightness...........................3-20
Entry Lighting...............................................3-20
Parade Dimming...........................................3-20
Reading Lamps............................................3-21
Electric Power Management...........................3-21Battery Run-Down Protection..........................3-22
Accessory Power Outlet(s).............................3-22
Ashtray(s) and Cigarette Lighter......................3-23
Analog Clock...............................................3-23
Climate Controls............................................3-24
Dual Climate Control System..........................3-24
Outlet Adjustment.........................................3-29
Passenger Compartment Air Filter...................3-29
Warning Lights, Gages, and Indicators............3-30
Instrument Panel Cluster................................3-31
Speedometer and Odometer...........................3-33
Trip Odometers............................................3-33
Tachometer.................................................3-34
Engine Speed Limiter....................................3-34
Safety Belt Reminders...................................3-35
Airbag Readiness Light..................................3-36
Passenger Airbag Status Indicator...................3-37
Charging System Light..................................3-38
Up-Shift Light...............................................3-38
Brake System Warning Light..........................3-39
Antilock Brake System (ABS) Warning Light.....3-40
StabiliTrak
®/Traction Control System (TCS)
Warning Light...........................................3-41
Engine Coolant Temperature Warning Light......3-41
Engine Coolant Temperature Gage..................3-42
Tire Pressure Light.......................................3-42
Section 3 Instrument Panel
3-1

Cruise Control
{CAUTION:
Cruise control can be dangerous where you cannot
drive safely at a steady speed. So, do not use the
cruise control on winding roads or in heavy traffic.
Cruise control can be dangerous on slippery roads.
On such roads, fast changes in tire traction can
cause excessive wheel slip, and you could lose
control. Do not use cruise control on slippery roads.
With cruise control, a speed of about 25 mph (40 km/h)
or more can be maintained without keeping your foot
on the accelerator. Cruise control does not work
at speeds below about 25 mph (40 km/h).
When the brakes are applied, the cruise control
turns off.
If the vehicle has the StabiliTrak
®system and begins
to limit wheel spin while you are using cruise control,
the cruise control will automatically disengage.
SeeStabiliTrak
®System on page 4-6. When road
conditions allow you to safely use it again, the cruise
control can be turned back on.The cruise control buttons
are located on the left side
of the steering wheel.
I(On/Off):Press to turn the system on or off.
The indicator light on the button turns on when cruise
control is on.
+ RES (Resume/Accelerate):Press to make the
vehicle accelerate or resume to a previously set speed.
SET−(Set/Coast):Press to set the speed or make
the vehicle decelerate.
[(Cancel):Press to cancel cruise control without
erasing the set speed from memory.CTS Shown, CTS-V
Similar
3-14

Setting Cruise Control
Cruise control will not work if the parking brake is set, or
if the master cylinder brake uid level is low.
The cruise control light on the instrument panel cluster
comes on after the cruise control has been set to
the desired speed.
{CAUTION:
If you leave your cruise control on when you are
not using cruise, you might hit a button and go
into cruise when you do not want to. You could be
startled and even lose control. Keep the cruise
control switch off until you want to use cruise
control.
1. Press the
Ibutton.
2. Get up to the desired speed.
3. Press the SET−button located on the steering
wheel and release it.
4. Take your foot off the accelerator.
Resuming a Set Speed
Suppose the cruise control is set at a desired speed
and then the brake is applied. This shuts off the cruise
control. But it does not need to be reset.
Once the vehicle is driving at about 25 mph (40 km/h)
or more, press the +RES button on the steering
wheel. The vehicle goes back to the previously set
speed and stays there.
Increasing Speed While Using Cruise
Control
To increase the cruise speed while using cruise control:
Press and hold the +RES button on the steering
wheel until the desired speed is reached, then
release it.
To increase vehicle speed in small increments,
press the +RES button. Each time this is done,
the vehicle goes about 1 mph (1.6 km/h) faster.
3-15