buttons CADILLAC DEVILLE 1994 7.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine L
Driver Information Center Control Buttons
INFORMATION Button
Pressing this button successively will display the AVG MPH, MPG AVG,
FUEL USED, OIL LIFE LEFT, and TIMER.
RESET Button
Pressing this button will reset the AVG MPH, MPG AVG, FUEL USED,
OIL LIFE LEFT, and TIMER when each function is displayed
TIMER Button
The TIMER feature is like a stop watch, in that you can clock the time it
takes to get from one point to another.
To operate, press either the TIMER button or successively press the
INFORMATION button until “TIMER
0O:OO:OO” is displayed on the
Driver Information Center. Each of the fields for the HOURS,
MINUTES, and SECONDS are
two numeric digits.
Once the “TIMER
0O:OO:OO:” is displayed, press the TIMER button to start
the timing feature. Press the TIMER button again to stop it. To reset it, press
and hold the RESET button until
the display reads “TIMER OO:OO:OO:”.
Press the INFORMATION button to exit from the TIMER function.
AVG MPH (Average Speed) Reset
Press successively the INFORMATION button to display the “AVG MPH”,
then press and hold the RESET button
until “0.0 AVG MPH” is displayed.
MPG AVG (Average Fuel Economy) Reset
Press successively the INFORMATION button to display the “MPG AVG ”,
then press and hold the RESET button until “0.0 AVG MPG” is displayed.
If the “AVG MPG” is displayed on the fuel Data Panel, another method
to reset both AVG MPG
is to press the AVG button on the Fuel Data
Panel
until 0.0 AVG MPG is shown in both displays.
Fuel Used Reset
Press successively the INFORMATION button to display the “FUEL
USED”on the Driver Information Center, then press and hold the
RESET button until “FUEL USED
8.0” is displayed.

Downloaded from www.Manualslib.com manuals search engine Oil Life Left Reset
Press successively the INFORMATION button to display the “OIL LIFE
LEFT ”) then press and hold the RESET button until “100 OIL LIFE
LEFT ” is displayed.
DISPLAY ON/OFF Button
Pressing this button will turn off the Driver Information Center, Trip and
Odometer, Electronic Climate Control and Fuel Data Center displays.
While displays are off, pressing the INFORMATION button will turn on
only the Driver Information Center. If any other button is pressed or a
driving warning message needs to be displayed, or
fuel level falls below
4 gallons, all the displays will come back on.
TRIP SET Button
Press and hold this button to set the Trip Odometer back to zero.
ENG/MET (English/Metric Button)
Press this button to switch from English (miles) and Degrees
(Fahrenheit), to Metric (kilometers) and Degrees (Celsius).
Driver Information Center Messages
These messages will appear if there is a problem sensed in one of your
vehicle’s systems. Vehicles that are first sold
in Canada or are export
vehicles will have a number after each message. This number helps to
identify that message, which is only displayed in English.
APPLY BRAKE TO SHIFT - 46
This message will appear if your vehicle is in “P” (Park) for about 15 seconds
and the brake
is not depressed. If you do not want this message to appear,
you
can cancel this message by holding the “OFF” and the Blue (cooler)
button on the Electronic Climate
Control panel for about 5 seconds. Hold the
same
two buttons again to have this message displayed again.
BATTERY NO CHARGE - 07
This message will appear
if your battery is not being charged. Have your
electrical system checked
by your Cadillac dealership at your earliest
convenience.
142
I
1

Downloaded from www.Manualslib.com manuals search engine The system probably will say to change the oil between 3000 miles
(5000 km) and 7500 miles (12500 km), but it may even say to change it
before
3000 under very severe conditions. It all depends on your driving
patterns. If it’s been
7500 miles (12500 km) it always says to change the oil.
There are
two things the system doesn’t do:
0 It can’t sense heavy dust in the places where you drive. If you drive in
a dusty area, you should change your oil every
3000 miles (5000 km)
or
3 months (whichever comes first), unless the display says to change
it even sooner than that.
It doesn’t check how much oil you have, so you’ll still have to check
for that.
To see how, see Engine Oil in the Index.
men You’ve Changed the Oil
When new oil is put in, you’ll need to reset your system. To do it, display
the “OIL LIFE INDEX” by pressing the INFORMATION button. Then
press and hold the RESET buttons until the display shows
“100 OIL
LIFE LEFT”
Electronic Level Control
This keeps your car level.
The ignition has to be “ON” for the level control to work. When you turn
the ignition off, you may hear the level control exhausting. The system
consists
of an electronic height sensor, a small electric air compressor,
and air adjustable shock absorbers mounted on the rear
of the vehicle.
If the system has a slight leak, the air compressor will run frequently for a
few seconds each time.
For
a massive air leak, the air compressor will stay on for approximately
7 minutes. You should see your dealer for service, but you can keep
driving your Cadillac.
149
.

Downloaded from www.Manualslib.com manuals search engine Fan Speeds
Push the (symbol)
button until “AUTO” is
displayed on the
screen.
At this setting, the fan speed
is controlled automatically.
If it is cold outside, the blower may not run in the maximum high fan
speed right away. The system checks the temperature
of the coolant to
assure it is warm enough to provide heat. When the coolant
is warm, the
controllers will allow the fan to ramp up to a higher speed. This prevents
cold air from blowing into the passenger compartment.
If you want the blower fan to run only at a fixed high speed, push the
(upper) button until you see “HI” on the display.
If you want the fan speed to be automatic, but you like the fan speed to
be higher than the.AUT0 setting, just push the buttons until “HI/AUTO”
is shown on the display.
If you want the blower to run only at a fixed
low speed, push the (low)
button until “LO” is shown on the display.
If you want the fan speed to run lower than the “AUTO” setting, push the
button until “AUTO
LO” is shown on the display.
DEFROSTER
--
Push this button to
remove fog or frost
from the windshield.
This setting sends most
of the air flow to the windshield with only a small
amount to the floor outlets.
The fan speed
will work automatically to maintain your requested interior
temperature.
If you need more air to your windshield, you should select a
higher fan speed.
In some cold start conditions, the AUTO fan speed may be limited until
the system warms up. This is normal
to prevent windshield fogging.
It will help a lot
if you first clear any ice and snow from the hood and the
air inlet (it’s between the hood and the windshield).

Downloaded from www.Manualslib.com manuals search engine -
The Lower Knob
Turn the lower knob to choose radio stations. Push the knob to switch
from
AM or FM.
Behind the lower knob is the Fade control. It fades the sound between
the front and rear speakers.
SCAN
When you press the SCAN button, the SCAN indicator in the display will
light and the radio will find the next station and stay there about
5
seconds. Then it will go to the next station and pause, and keep doing
that until
you push either the SCAN or upper knob.
SEEK
This button selects stations, but it doesn’t keep moving as SCAN does.
When
you push SEEK the radio will automatically go to the next
strongest station and stay there.
AM-ST (AM Stereo)
Pressing the AM-ST button enables the AM stereo reproduction of an
AM station that is broadcasting in stereo. Switching to stereo on weaker
non
AM stereo stations improves fidelity, but may increase noise due to
interference from power lines, neon signs, atmosphere conditions, and
unwanted stations. The STEREO indicator light
only comes on when the
radio is tuned to a clear, noise free station broadcasting
C-QUAM@ AM
stereo.
Pushbuttons
You can set the pushbuttons to get up to 14 favorite stations (seven on
FM and seven more on AM). Just:
Choose either AM or FM.
Tune in the station.
Push the SET button.
Within 5 seconds, push one of the four pushbuttons.
Repeat these steps for each of the 5 pushbuttons.
,-
L

Downloaded from www.Manualslib.com manuals search engine In addition to the 14 stations set as above, up to three additional stations
may be present
on each band by pressing two adjoining buttons at the
same time. Just:
0 Tune in the desired station.
Press the SET button.
0 Within 5 seconds, press any two adjoining pushbuttons at the same
time. (The station will return when the same
two buttons are pressed
again
.)
-. Five Band Graphic Equalizer
The equalizer lets you set the bass, midrange and treble to sound just the
way you want. The
60 and 250 controls work the bass side. The midrange
is the 1K The 3.3K and 10K are the treble sound controls.
We suggest that
you start with the midrange (1K) control lever in the
center. Then move the other controls until you get the sound you want.
Moving the control levers up
(+) gives your more sound in that range.
Moving it down
(-) gives you less.
If
the 10 K control lever is near the top, you may hear a hissing sound. To
eliminate it, move the 10K control lever down until the hiss goes away.
Your Cassette Tape Player
Your cassette tape player works best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are so thin that they may not
work well in this player.
If you look at the tape, or on its label or box, it should say whether its bias,
“equalization” is
70 microseconds (70 p) or 120 microseconds (120 p).
Chrome and metal tapes are 70 p sec and standard iron tapes are 120 p sec.
Your tape player
will adjust automatically for either type of cassette tape.
Setting The Clock On The AM FM ETR Sound System
Push SET and within 5 seconds,
Press and hold SCAN until the correct hour appears.
0 Then press and hold SEEK until the correct minute appears. Your
clock is set.
161

Downloaded from www.Manualslib.com manuals search engine To Play A Cassette Tape
Turn the radio on.
Insert the cassette through the tape door. (The “TAPE” indicator in
If you hear nothing or hear just a garbled sound, the cassette may not be
in squarely. Push the STOP- EJCT button to remove the tape and start
over. The tape equalization is automatically sensed and set. Insertin the
cassette also automatically disables DNR@* and activates DOLBY
8
noise reduction.
DNR‘ is the Dynamic Noise Reduction.
It helps remove background hiss
noise from the radio.
the
display
will light.)
*DNR@
is a registered trademark of National Semiconductor Corporation.
Once the tape is playing, use the upper and lower knobs to adjust the
volume and balance, just as you do for
the radio. Push the upper knob
to change tape direction. The arrow in the display shows which
direction the tape is being played.
Forward and Reverse 4
To rapidly advance the tape. press and the tape will rapidly go forward
until you press the STOP-EJCT button.
To rapidly reverse the tape. press 4 and the tape will rapidly reverse
until you press the STOP-EJCT button.
SEARCH
When you are playing a tape, the search feature lets you advance ahead
to the start
of the next selection or rewind to the beginning of the
selection being played. Pressing the or
4 buttons will then advance or
rewind to the beginning or end
of the selection being played.
NOTICE: -
There must be at least a five second pause between selections on
the tape for the SEARCH feature to operate properly.
-
162

Downloaded from www.Manualslib.com manuals search engine SEEK
This button selects stations, but it doesn’t keep moving as SCAN does.
When you push SEEK either
up or down the radio will automatically go
to the next strongest station and stay there.
Pushbuttons
You can set the pushbuttons to get up to ten favorite stations (five on FM
and five more on AM). Just:
Choose either AM or FM.
Tune in the station.
0 Push the SET button.
Within 5 seconds, push one of the five pushbuttons.
Repeat these steps for each of the five pushbuttons.
Your Cassette Tape Player
Your cassette tape player works best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are
so thin that they may not
work well in this player.
If you look at the tape, or on its label or box, it should say whether
its
bias, “equalization” is 70 microseconds (70 p) or 120 microseconds
(120 p). Chrome and metal tapes are 70 sec and standard iron tapes are
120 p sec. Your tape player will adjust automatically for either type of
cassette tape.

Downloaded from www.Manualslib.com manuals search engine there about 5 seconds. Then it will go to the next station and pause, and
keep doing that until
you push either the SCAN or upper knob.
SEEK
This button selects stations, but it doesn’t keep moving as SCAN does.
When
you push SEEK either up or down the radio will automatically go
to the next strongest station and stay there.
Pushbuttons
You can set the pushbuttons to get up to ten favorite stations (five on FM
and five more on AM). Just:
0 Choose either AM or FM
0 Tune in the station.
0 Push the SET button.
Within 5 seconds, push one of the five push buttons.
0 Repeat these steps for each of the five push buttons.
Your Cassette Tape Player
Your cassette tape player works best with tapes that are 30 to 45 minutes
long on each side. Tapes longer than that are
so thin that they may not
work well in this player.
If you
look at the tape, or on its label or box, it should say whether its
bias, “equalization”
is 70 microseconds (70 p) or 120 microseconds
(120 p). Chrome and metal tapes are 70 1-1 sec and standard iron tapes are
120 p sec. Your tape player will adjust automatically for either type of
cassette tape.
169