CADILLAC DEVILLE 1996 7.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine Resuming a Set Speed
Setting the cruise control at
a desired speed and then
applying the brake
will end
the cruise function. Once
you’re going about
25 mph
(40 km/h) or more, you can
move the cruise control
I switch from ON to R/A
(Resume/Accelerate) for
about half a second to reset.
This returns you
to your
desired preset speed.
I
Remember, if you hold the switch at R/A longer than
half a second, the vehicle will accelerate until you
release the switch or apply the brake.
You could be
startled and even lose control.
So unless you want to
go faster, don’t hold the switch at RJA.
Increasing Speed While Using Cruise Control
There are two ways to increase your speed. Here’s
the first:
1. Use the accelerator pedal to go to a higher speed.
2. Push the button at the end of the lever and then
release the button
and the accelerator pedal. You’ll
now cruise at the higher speed.
Here’s
the second way to increase speed:
0 Move the cruise switch from ON to R/A. Hold it
there until you reach
a desired speed and then release
the switch.
0 To increase your speed in very small amounts, move
the switch to R/A. Each time you
do this, your
vehicle will
go about 1 mph (1.6 km/h) faster.
The accelerate feature will only work after you’have set the
cruise control speed by pushing the SET CRUISE button.
0
0
2-38

Downloaded from www.Manualslib.com manuals search engine c
c
c
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
0 Push in the button at the end of the lever until you
reach a desired lower speed, then release
it. A
CRUISE ENGAGED message will then display.
To slow down in very small amounts, push the
button for less than half a second. Each time you do
this, you’ll go
1 mph (1.6 b/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. when
you take
your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness
of the hills.
When going up steep hills,
you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down.
Of course, applying the brake
takes you out
of cruise control. Many drivers find this to
be too much trouble and don’t use cruise control on steep hills.
Ending Cruise Control
There are two ways to end cruise control:
Step lightly on the brake pedal.
Move the CRUISE switch to OFF.
Erasing Speed Memory
The cruise control set speed memory is erased when you
turn off the cruise control
or the ignition.
2-39

Downloaded from www.Manualslib.com manuals search engine Lamps
1
The control on the left side
of the instrument panel
controls these lamp systems:
e
e
e
e
e
e
e
e
Headlamps
Taillamps
Parking Lamps Sidemarker Lamps
License Plate Lamp
Underhood Lamp
Instrument Panel Lights
Interior Courtesy Lamps
Pull the knob out to the
fist stop to turn on the parking
and taillamps, sidemarker lamps and instrument panel lights. Pull the
knob out all the way to turn on the
headlamps.
You can brighten or dim the instrument
cluster by rotating the headlamp
knob. Press the knob
all the way in to turn them off. The exterior lamps
will automatically turn
on after several seconds of
wiper activation.
Headlamps
Wiper Activated Headlamps
This feature activates the headlamps and parking lamps after the windshield wipers have been in
use for
approximately 20 seconds. ’
In order to operate the wiper activated headlamps, the
twilight sentinel must
be in the on position. This feature
lights the way
in poor weather and it also makes your
vehicle more visible to other drivers. If the wiper activated headlamps are
on, and the ignition switch is
turned
off, the wiper activated headlamps will
immediately
turn off.
The wiper activated headlamps will deactivate
if you
turn off the twilight sentinel or if the windshield wipers
have been turned
off for a period of one or two seconds.
2-40

Downloaded from www.Manualslib.com manuals search engine P
c
21
c
P
c
Lamps on Reminder
You will hear a warning chime if you pull the key from
the ignition while leaving the lamps
on, if the manual
headlamp control is activated. An exception to this is
when you’re using twilight sentinel.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during
the day.
DRL can be helpful
in many different driving
conditions, but they can be especially helpful in
the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered.
The
DRL system will make the low-beam headlamps
come
on at reduced brightness when:
the ignition is on,
the headlamp switch is off and
the transaxle is not in PARK (P).
When DRL are on, only the low-beam headlamps (at
reduced brightness) will be
on. No other exterior lamps
such as the parking lamps, taillamps, etc. will be on
when the
DRL are being used. Your instrument panel
won’t be
lit up either. When
it’s dark enough outside, the low-beam
headlamps (at reduced intensity) will change
to normal
low-beam headlamp operation. When it’s bright enough
outside, the regular lamps will go
off, and the low-beam
headlamps change to the reduced brightness
of DRL.
To idle your vehicle with the DRL off, tum off the
twilight sentinel switch and shift the transaxle into
PARK (P). Placing your vehicle in PARK (P) disables
the DRL. The DRL will stay
off until you shift out of
PARK (P).
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Cornering Lamps
The cornering lamps come on when the headlamps or
parking lamps are on and you signal a turn. They
provide more light for cornering.
Underhood Lamp
Turn the parking lamps on to operate the underhood lamp. The underhood
lamp will come on when the hood
is open.
2-41

Downloaded from www.Manualslib.com manuals search engine Twilight Sentinel
I W The control is next to
the headlarnp
knob. It
automatically switches the
lamps on and off by sensing
how dark it is outside.
To operate the twilight sentinel, leave the lamp knob off
and move the TWILIGHT control to any position
but
OFF.
If you move the control all the way to the right, the
lamps will remain
on for approximately three minutes
after the ignition has been turned to the
OFF or LOCK
position. If you move the control so it is just on, the
lamps will go off quickly when you turn the ignition switch out
of RUN. You can adjust the delay time from
only a few seconds to three minutes.
Light Sensor
The light sensor for the DRL and the twilight sentinel is
located in the center of the front defogger grille. If you
cover the sensor, it will read “dark” and the lamps will\

come on.
2-42

Downloaded from www.Manualslib.com manuals search engine c
c-
Exterior Lighting Battery Saver
The exterior lamps will turn off approximately
10 minutes after the ignition is turned to LOCK or ACC, if
the manual park lamp control is on. This protects draining
the battery
in case you have left the headlamps or parking
lamps on. Use the control knob to
turn the lamps back on
indefinitely. To delay the lamps from tuming off, see
"Twilight Sentinel" earlier in this section.
Interior Lamps
Instrument Panel Intensity Control
As you turn the headlamp knob clockwise, the
instrument panel lights will brighten. Turning the
headlamp knob all the way clockwise will turn on the interior lamps.
Lamp Monitors
The rear taillamp monitors
are located at the top
center
of the back glass.
You will see them as you
look through the inside
rearview mirror. The two
red indicators will
illuminate to show that the
taillamps and brake lamps
are working.
Illuminated Entry System
The illuminated entry system turns on the courtesy lamps
and the backlighting
to the door switches and headlamp
knob control when a door is opened or if you press the
Remote Keyless Entry
(RKE) button. Note that the
illuminated entry system
is photocell dependent which
means that it must
be dark outside in order for the
courtesy lamps to
turn on. The courtesy lamps will turn
off approximately 20 seconds after the last door is closed.
2-43

Downloaded from www.Manualslib.com manuals search engine Reading Lamps (Concours Only) Map Lamps
The reading lamps are located in the roof. These lamps
come
on when any door is opened and it is dark outside.
Press the button
to turn them on. Press it again to turn
them
off.
If the reading lamps are left on, they automatically shut
off 10 minutes after the ignition has been turned off.
Courtesy Lamps (DeVille Only)
The courtesy lamps are located in the roof in the rear
seat. These lamps come
on with the lamp knob or when
any door is opened and it is dark outside.
3
These lamps are located in the overhead panel. Press the
button
to turn them on. Press it again to turn them off.
2-44

Downloaded from www.Manualslib.com manuals search engine c
c
c
c
c
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle’s battery
against drainage from the interior lamps,
trunk lamp,
glove box lamp, cigarette lighters or the garage door opener. When the ignition is turned
OFF, the power to
these features will automatically
turn off after 10 minutes
(three minutes if a new car has
15 miles or less). Power
will
be restored for an additional 10 minutes if any door
is opened, the
trunk is opened or the courtesy lamp
switch is turned on.
Battery Guard Storage
This feature is for long term use and miust be
programmed through the DIC while the ignition is in the
RUN position. Battery guard storage protects the battery
by placing the vehicle in a storage mode
so that the
radio, amplifiers, instrument cluster and Remote Keyless
Entry
(RKE) will not drain the battery over a long
period
of time.
To begin programming, press the INFORMATION
and RESET buttons at
the same time for approximately
two seconds. Press the RESET button to answer
“yes” and press the INFORMATION button to indicate a “no” response. The first prompt
to appear relates to the automatic door
locks. This feature can be bypassed by pressing the
INFORMATION button. The STORAGE MODE?
prompt appears next. To select, press the
RESET button.
ENABLE STORAGE MODE? will then appear. A yes
or no response must be given. If the INFORMATION
(no) button is pressed, the DISABLE STORAGE
MODE? prompt will appear. Once again, a yes or no
response is required.
Once the battery guard has been programmed, your
vehicle will enter the storage mode approximately
20 minutes after the ignition key has been turned off.
The RKE will also be disabled at this point. The RKE
will reactivate when a door or the trunk is opened,
however,
if your vehicle is left inactive for another
20 minutes the RKE will re-enter the storage mode.
Your vehicle will stay in the storage mode until the
ignition key
is turned out of LOCK. The system will
“wake-up” when the
door key is inserted into the door
however, your vehicle will remain in the storage mode.
The ignition must be out of
LOCK before the battery
guard is disabled.
2-45

Downloaded from www.Manualslib.com manuals search engine Mirrors
Electrochromic DaylNight Rearview Mirror
Your Cadillac has an electrochromic day/night
rearview mirror.
This mirror automatically changes to reduce glare
from '
headlamps behind you. A photocell on the back of the
mirror senses when it is becoming dark outside. Another
photocell built into the mirror surface senses when
headlamps are behind you.
At night, when the glare is too high, the mirror will
gradually darken
to reduce glare (this change may take a
few seconds). The
mirror will return to its clear daytime
state when the glare is reduced.
3
4
3

Downloaded from www.Manualslib.com manuals search engine On/Off Switch Time Delay
This feature prevents rapid changing
of the mirror from
the night mode to the day mode as you drive under lights and through traffic.
c I
I
I
Press the button at the base of the mirror to turn on the
automatic feature. The button has
an indicator light to
show it is on. Press the button to turn the automatic
feature
off.
Reverse Gear Day Mode
The reverse mode is another important feature of the
automatic mirror. When the shift lever is placed in
REVERSE (R), the mirror changes to the day mode.
This gives
you a bright image in the mirror as you
back up.
Cleaning Photocells
Use a cotton swab and glass cleaner to clean the front
and rear photocells that make the auto-dimming
feature
work.
2-47