buttons CADILLAC DEVILLE 2002 8.G User Guide

2-129
Navigation (Option)
Navigation Display Controls
The display screen is located in the center on the
instrument panel. There are ªhardº buttons and a touch
sensitive screen.Your vehicle may be equipped with a turn by turn
navigation guidance system that includes a CD ROM
map media covering nine regional areas throughout the
contiguous United States and Canada. In addition, the
system includes intersection and freeway entrances,
route planning, a programmable address book, points of
interest, a list of restaurants, emergency phone numbers,
and a list of hotels and motels for all of the major cities
on the CD. The navigation system can also
communicate with the radio data system to receive
broadcast announcements on traffic, weather
information and emergency alert communications.
For more information on how to use this system, see
ªNavigationº supplement.

3-12
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off. See
ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two
-second delay before the clock
goes into time
-set mode.
AM-FM Stereo with Cassette Tape and
Compact Disc Player
Playing the Radio
PWR (Power): Press this knob to turn the system on
and off.
VOL (Volume): Turn this knob clockwise to increase
volume. Turn it counterclockwise to decrease volume.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing one of these buttons.

3-13
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.
Finding a Station
BAND: Press this button to select AM, FM1 or FM2.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds
to scan radio stations and associated tone settings.
The radio will go to a station, play for five seconds,
then go on to the next station. Press this button again
to stop scanning.To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.
Setting Preset Stations
The six numbered pushbuttons let you return to
your favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2), by performing the
following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds until you hear a beep.
5. Repeat the steps for each pushbutton. Whenever
you press that numbered pushbutton for less than
two seconds, the station you set will return.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.

3-15

RW (Rewind): Press the left arrow to rewind the
tape rapidly. The radio will play while the tape rewinds.
You may use your station pushbuttons to tune to another
radio station while in rewind. Press the left arrow again
to return to playing speed.
FF
 (Fast Forward): Press the right arrow to fast
forward to another part of the tape. The radio will play
while the tape advances. You may use your station
pushbuttons to tune to another radio station while in fast
forward. Press the right arrow again to return to playing
speed.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button to listen to selections for a few
seconds. The tape will go to a selection, play for a few
seconds, then go on to the next selection. Press this
button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing.
(Eject): Press this button to the right of the
cassette tape player to remove a tape. The radio will
play. Eject may be activated with the radio off and/or
the ignition off.
Cassette Tape Messages
If an error occurs while trying to play a cassette tape, it
could be for one of the following reasons:

The cassette tape is tight and the cassette player
cannot turn the hubs of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.

The cassette tape is broken. (Check to see if your
tape is broken. Try a new tape.)
CLEAN TAPE: If this message appears on the display,
the cassette tape player needs to be cleaned. It will still
play tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index.
If any error occurs repeatedly or if an error can't be
corrected, contact your dealer.

3-18
AVC (Automatic Volume Control): With AVC, your
audio system monitors the noise in the vehicle. Then,
AVC adjusts the volume level so that it always sounds
the same to you. To use AVC, press and hold the TONE
button until AUTO VOLUME CONTROL OFF appears
on the display. Then press the LEVEL plus symbol.
AUTO VOLUME CONTROL ON will appear on the
display. AVC VOLUME will appear on the display any
time you adjust the volume while AVC is on. To turn
AVC off, press and hold the TONE button until AUTO
VOLUME CONTROL ON appears on the display. Then
press the LEVEL minus symbol. AUTO VOLUME
CONTROL OFF will appear on the display.
HR (Hour) or MN (Minute): Display the time with the
ignition off by pressing one of these buttons.
SOURCE: Press this button to select a source, either
cassette or compact disc. The audio source must be
loaded to play. Available loaded sources are shown on
the display. If a source is being used, it will be
underlined on the display. If none of the audio sources
are loaded, NO SOURCE LOADED will appear on the
display. Press this button again or press BAND to switch
back to the radio.Finding a Station
BAND: Press this button to select AM, FM1 or FM2,
weather or XM1 or XM2 if your radio is equipped with
XM
Satellite Radio Service.
~' TUNE SEEK !': When this button is pressed it
has two positions. Press this button to the first position
to manually tune to the next or previous stations. If this
button is held at the first position for a few seconds, the
radio will continue tuning until this button is released.
Press this button to the second position and release it to
seek to the next or previous radio station.
SCAN: Press this button for less than two seconds to
scan radio stations. The radio will go to a station, play
for five seconds, then go on to the next station. Press
this button again to stop scanning.
To scan preset stations, press and hold SCAN for more
than two seconds until you hear a beep. The radio will
go to the first preset station stored on your pushbuttons,
play for five seconds, then go on to the next preset
station. Press SCAN again to stop scanning. The radio
will scan preset stations with a strong signal only.

3-19
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations and associated tone and DSP settings.
The RDS PTY mode must be off to use this mode. You
can set up to 36 stations (six AM, six FM1, six FM2,
six XM1, six XM2 and six weather if your radio is
equipped with the XM Satellite Radio Service), by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select AM, FM1, FM2, XM1, XM2
or weather.
3. Tune in the desired station.
4. Press and hold one of the six numbered pushbuttons
for more than two seconds. Whenever you press that
numbered pushbutton for less than two seconds, the
station you set will return.
5. Repeat the steps for each pushbutton.
When battery power is removed and later applied, you
will not have to reset your radio presets because the
radio remembers them.Setting the Tone (Bass/Treble)
TONE: Press and release this button until the desired
tone BASS, TREBLE or MIDRANGE appears on the
display. The radio keeps separate tone settings for each
band, preset (except weather band presets) and source.
- LEVEL +: After selecting the desired tone control,
press the plus or minus symbol on this button to select
the desired level.
To save the tone settings for your presets, press and hold
the numbered button for the desired preset for more than
two seconds until you hear a beep.
Adjusting the Speakers (Balance/Fade)
TONE: Press and release this button until BALANCE
or FADE appears on the display.
- LEVEL +: After selecting the desired control, press
the plus or minus symbol on this button to select the
desired level.
To save the tone settings for your presets, press and hold
the numbered pushbutton for the desired preset for more
than two seconds until you hear a beep.

3-21
HR (Hour) or MN (Minute): When tuned to an RDS
station, press these buttons to display the time for the
current station. STATION TIME IS will be displayed. If a
time has not been sent to the radio, NO STATION TIME
will be displayed. If you have recently tuned to the station,
you may need to wait a minute before the time is available
to the radio. To set the clock to the current displayed
station time, press HR or MN until TIME UPDATED is
displayed. You must be tuned to an FM RDS station.
RDS Messages
ALERT: This type of announcement warns of national or
local emergencies. You will not be able to turn off alert
announcements. ALERT appears on the display when an
alert announcement plays. The radio uses TA volume during
these announcements. To increase volume, turn the
PWR/VOL knob clockwise. Turn it counterclockwise to
decrease volume. TA VOLUME will appear on the display
while the volume is being adjusted. When an alert
announcement comes on the current radio station or a related
network station, you will hear it, even if the volume is muted
or a cassette tape or compact disc is playing. If the radio tunes
to a related network station for an alert announcement, it will
return to the original station when the announcement is
finished. If the cassette tape or compact disc player is
playing, play will stop for the announcement and resume
when the announcement is finished.TA (Traffic Announcement): This feature allows
the radio to receive traffic announcements even with
the volume muted, or when listening to a CD or
cassette tape.
When the TA button is pressed and released, the radio
will search for a station with TA if the current station is
not TA capable. During the search TA will flash on the
display. Once a TA station is found, TA will appear on
the display and the traffic announcement will be played.
If no station broadcasting traffic announcements is
found, NO TRAFFIC STATION FOUND will appear on
the display. If the TA button is pressed and held for
two seconds, the radio will search for the next available
TA station.
While a traffic announcement plays, the radio uses a
special type of volume called TA volume. To increase
TA volume, turn the VOL knob clockwise. Turn it
counterclockwise to decrease volume. TA VOLUME
will appear on the display while the volume is
being adjusted.

3-23
Setting PTY Preset Stations
PTY (Program Type): Press this button to activate
program type mode. PTY will appear on the display.
To select a desired PTY, press the LEVEL plus or minus
buttons to scroll up and down through the PTY listing.
PTYs might include rock, popular, jazz, etc. Once the
desired PTY is displayed, press either SEEK arrows or
the SCAN button to enter the PTY mode. This will
allow you to find the next or previous station available
that is broadcasting the selected PTY.
The SEEK arrows or the SCAN button may continue
to be used to search for the desired PTY as long as
PTY appears on the display. To cancel PTY mode, press
and release the PTY button. PTY will disappear from
the display.Playing a Cassette Tape
With the radio on, insert a cassette tape. The tape will
begin playing as soon as it is inserted. When one side of
your cassette tape is done playing, auto reverse plays the
other side of your cassette tape. A cassette tape may be
loaded with the radio off but it will not start playing
until the radio is on. If you want to insert a cassette tape
when the ignition is off, first press the eject button.
While the tape is playing, use the VOL, TONE, LEVEL
and DSP controls just as you do for the radio. Other
controls may have different functions when a tape is
inserted. The display will show an underlined tape
symbol. TAPE PLAY will appear on the display when a
tape is playing, with an arrow to indicate which side of
the tape is playing.
If an error appears on the display, see ªCassette Tape
Messagesº later in this section.

3-27
Navigation/Radio System (Option)
Navigation/Radio Display and ControlsThe display screen is located in the center of the
instrument panel. There are ªhardº buttons and a touch
sensitive screen.
Your vehicle may be equipped with an AM
-FM stereo
navigation radio system that includes digital sound
processing (DSP), a Radio Data System (RDS) with
program ªtypeº selections (PTY) that will seek out the
kind of music you want to listen to. The radio system
can also communicate with your navigation system to
broadcast announcements on traffic, weather and
emergency alert communications. For information on
how to use this system, see the ªNavigation/Radio
Systemº supplement.

3-29
Close the door by sliding it all the way to the right.
When the door is closed, the changer will begin
checking for discs in the magazine. This will continue
for up to one and a half minutes, depending on the
number of discs loaded.
Whenever a CD magazine with discs is loaded in the
changer, the CD changer symbol will appear on the
radio display. If the CD changer is checking the
magazine for CDs, the CD symbol will flash on the
display until the changer is ready to play. When a CD
begins playing, a disc and track number will be
displayed. The disc numbers are listed on the front of
the magazine.1 PREV (Previous): Press this pushbutton to seek to the
previous track on the CD. If playing the first track of the
CD, pressing the PREV pushbutton will seek to the last
track of the CD. The sound will mute while seeking.
2 NEXT: Press this pushbutton to seek to the next track
on the CD. If playing last track of the CD, pressing the
NEXT pushbutton will seek to the first track of the CD.
3 RW (Rewind): Press and hold this pushbutton to
reverse quickly through a track.
4 FF (Fast Forward): Press and hold this pushbutton to
advance quickly through a track.
5 DISC: Press this pushbutton to select the next disc in
the changer. Each time you press this button, LOADING
will appear on the display and the disc number on the
radio display will go to that of the next available CD.
6 RDM (Random): Press this pushbutton to hear the
tracks in random, rather than sequential, order. RDM
will appear on the display. Press the PREV or NEXT
pushbuttons while RDM is on the display to randomly
seek through discs. Press RDM again to turn off random
play. This feature may not be available on your radio.
SCAN: Press this button. You will hear the first few
seconds of the first track on each disc. Press this button
again to stop scanning. The CD will mute while
scanning and SCAN will appear on the display.