key CADILLAC ELDORADO 2002 10.G Service Manual

2-91
4. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes,
or press the NO INFO RESET button to indicate no.
Once you have indicated the mode that you want
with a yes response, FEATURE ON will appear on
the display. FEATURE OFF appears when you
indicate a no response, and the display will advance
to the next mode.
REMOTE RECALL MEMORY will appear
once a mode has been selected for lock/unlock
confirmation feature.
If you press the SKIP INFO button, the menu will
advance to the next feature available for programming.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.Remote Recall Memory (If Equipped with
Memory Personalization)
Memory settings that have been previously programmed
(climate control settings, radio preset settings, exterior
lighting choices, remote confirmation choices and
programmable automatic door lock choices) can be
recalled by using the remote keyless entry transmitter
or by placing the key in your vehicle's ignition.
Programmable Modes
Mode 1 (REMOTE RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the button
with the unlock symbol on the remote keyless entry
transmitter is used to unlock the vehicle.
Mode 2 (KEY IN RECALL MEMORY):
The previously programmed driver's seat and mirror
positions are automatically recalled when the ignition
is turned to RUN.

2-92
Before your vehicle was shipped from the factory, it was
programmed to enable Mode 1. The mode to which the
vehicle was programmed may have been changed since
it left the factory. To determine the mode to which the
vehicle is programmed or to program the vehicle to a
different mode, do the following:
1. Enter feature programming following the
instructions listed previously.
2. Press the SKIP INFO button until REMOTE
RECALL MEMORY appears on the display.
3. Press YES TRIP RESET to select this feature
for programming.4. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes
to turn this feature on, or press NO INFO RESET to
turn this feature off.
FEATURE ON is displayed after a yes response.
If you respond with no, FEATURE OFF is briefly
displayed. Then, KEY IN RECALL MEMORY
will appear on the display, and you will be able to
program this feature.
MIRROR TILT IN REV will appear on the display
once a mode has been selected for the remote recall
memory feature.
If you press the SKIP INFO button, the menu will
advance to the next feature available for programming.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-94
Storage Mode Personalization
When this feature is turned on, the vehicle will enter
the storage mode about 20 minutes after the ignition
has been turned to LOCK. The vehicle will stay in the
storage mode until the ignition key is turned out of
LOCK. The system will ªwake
-upº when the door
key is inserted into the door; however, your vehicle will
remain in the storage mode. The ignition must be out
of LOCK before the battery guard is disabled.
Programmable Modes
Mode 1 (STORAGE MODE): Turns feature on.
Mode 2 (STORAGE MODE): Turns feature off.
Before your vehicle was shipped from the factory, it was
programmed to Mode 2. The mode to which the vehicle
was programmed may have been changed since it left
the factory. To determine the mode to which the vehicle
is programmed or to program the vehicle to a different
mode, do the following:
1. Enter feature programming following the
instructions listed previously.
2. Press the SKIP INFO button until STORAGE
MODE appears on the display.3. Press YES TRIP RESET to select this feature
for programming.
4. A yes or no response must be made after each mode
is displayed in order to continue to the next mode.
Press the YES TRIP RESET button to indicate yes
to turn this feature on, or press NO INFO RESET to
turn this feature off.
FEATURE ON is displayed after a yes response.
If you respond with no, FEATURE OFF is
briefly displayed.
This is the last available programmable feature.
A yes or no response will end out of the Driver
Information Center (DIC) display.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

3-10 HVAC Steering Wheel Controls
Some heating and cooling
controls can be adjusted at
the steering wheel. Other
touch controls operate some
audio controls. See ªAudio
Steering Wheel Controlsº
in the Index.
(Fan): Press the up arrow lever to increase the fan
speed and the down arrow lever to decrease fan speed.
TEMP: Press the up arrow lever to increase
the temperature and the down arrow lever to
decrease temperature.
Climate Control Personalization (If Equipped)
This feature allows both drivers (driver 1 or 2 depending
on the number on the back of your remote keyless entry
transmitter) to personalize their own climate control
settings. For more information, see ªMemory and
Personalization Featuresº in the Index.
Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all of its controls to be sure you're getting the
most out of the advanced engineering that went into it.
Your vehicle has a feature called Retained Accessory
Power (RAP). With RAP, you can play your audio
system even after the ignition is turned off.
See ªRetained Accessory Powerº in the Index.
Setting the Clock
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two
-second delay before the clock
goes into time
-set mode.

3-31 Radio Personalization with Home and
Away Feature (If Equipped)
If DRIVER 1 (HOME or AWAY) PRESETS or
DRIVER 2 (HOME or AWAY) PRESETS appears
in the display when the radio is first turned on,
your vehicle is equipped with this feature.
This feature allows the driver to return to the last used
audio source (radio, cassette or CD) using their remote
keyless entry transmitter. This feature can also store
and recall AM and FM presets, volume, tone and the
last selected radio station. The number on the back of
each transmitter (1 or 2) corresponds to driver 1 or 2.
If transmitter 1 is used to enter the vehicle, the last
used audio source and/or settings set by driver 1 will be
recalled. If transmitter 2 is used to enter the vehicle, the
last used audio source and/or settings set by driver 2 will
be recalled. The settings can also be recalled by pressing
the MEMORY seat buttons 1 or 2 located on the
driver's door.
Your radio can store home and away presets. Home and
away presets allow you to use one set of preset radio
settings in the area where you live, and another set when
you go out of town. That way, you will not need to
reprogram your presets every time you travel. With the
radio off and the clock displayed, use fast forward andreverse to select home or away presets. To select the
away presets, press and hold FF for five seconds until
you hear a beep. The next time the radio comes on,
the away presets will be active. To select the home
presets, press and hold RW or REV for five seconds
until you hear a beep. The next time the radio comes on,
the home presets will be active.
When battery power is removed and later applied, you
will not have to reset your home radio presets because
the radio remembers them. However, you will have to
reset your away radio presets.
Theft-Deterrent Feature
THEFTLOCK
is designed to discourage theft of
your radio. Your vehicle has a ªbuilt
-inº theft-deterrent
feature on each radio that is automatic
-- there is
no programming required. The radio in your vehicle
cannot be used in any other vehicle. When the radio
was originally installed in your vehicle at the factory,
it stored the Vehicle Identification Number (VIN).
Each time the ignition is turned on, the VIN is verified.
If the vehicle's VIN does not match the VIN stored in
the radio, THEFTLOCK will be activated and the audio
system will not play. If the radio is removed from your
vehicle, the original VIN in the radio can be used to
trace the radio back to your vehicle.

4-4
According to the American Medical Association, a
180
-lb. (82 kg) person who drinks three 12-ounce
(355 ml) bottles of beer in an hour will end up with a
BAC of about 0.06 percent. The person would reach the
same BAC by drinking three 4
-ounce (120 ml) glasses
of wine or three mixed drinks if each had 1
-1/2 ounces
(45 ml) of a liquor like whiskey, gin or vodka.
It's the amount of alcohol that counts. For example,
if the same person drank three double martinis
(3 ounces or 90 ml of liquor each) within an hour,
the person's BAC would be close to 0.12 percent.
A person who consumes food just before or during
drinking will have a somewhat lower BAC level.
There is a gender difference, too. Women generally have
a lower relative percentage of body water than men.
Since alcohol is carried in body water, this means
that a woman generally will reach a higher BAC level
than a man of her same body weight when each has
the same number of drinks.
The law in an increasing number of U.S. states, and
throughout Canada, sets the legal limit at 0.08 percent.
In some other countries, the limit is even lower.
For example, it is 0.05 percent in both France and
Germany. The BAC limit for all commercial drivers in
the United States is 0.04 percent.
The BAC will be over 0.10 percent after three to
six drinks (in one hour). Of course, as we've seen,
it depends on how much alcohol is in the drinks,
and how quickly the person drinks them.

4-31 Dinghy Towing
NOTICE:
Towing your vehicle with all four wheels on the
ground will damage drivetrain components.
Your vehicle was not designed to be towed with all four
wheels on the ground. If your vehicle must be towed,
you should use a dolly. SeeªDolly Towingº later in this
section for more information.
Dolly Towing
Your vehicle can be towed using a dolly. To tow your
vehicle using a dolly, follow these steps:
1. Put the front wheels on the dolly.
2. Put the vehicle in PARK (P).
3. Set the parking brake and then remove the key.
4. Clamp the steering wheel in a straight
-ahead position.
5. Release the parking brake.

5-2
Hazard Warning Flashers
Your hazard warning flashers let you warn others. They
also let police know you have a problem. Your front and
rear turn signal lamps will flash on and off.
The hazard warning flasher button is located on the right
side of the steering column, near the ignition switch.
The hazard warning flashers work no matter what
position your key is in, and even if the key isn't in.
Press the button to make your front and rear turn signal
lamps flash on and off.

6-7
The fuel door release is
located above the radio
on the Driver Information
Center (DIC) and on
the remote keyless
entry transmitter.
These buttons work only when the shift lever is in
PARK (P) or NEUTRAL (N) and the VALET lockout
switch is in OFF.
An alternate fuel door
release is located inside
of the trunk on the driver's
side. Pull it to release the
fuel door.While refueling, hang the fuel cap by the tether from
the hook on the filler door.
To remove the fuel cap, turn it slowly to the left
(counterclockwise). The fuel cap has a spring in it;
if you let go of the cap too soon, it will spring back
to the right.

6-28
Power Steering Fluid
The power steering fluid
reservoir and dipstick
are located next to the
coolant surge tank on
the passenger's side of
the vehicle.
When to Check Power Steering Fluid
It is not necessary to regularly check power steering
fluid unless you suspect there is a leak in the system or
you hear an unusual noise. A fluid loss in this system
could indicate a problem. Have the system inspected and
repaired. See ªEngine Compartment Overviewº in the
Index for reservoir location.
How to Check Power Steering Fluid
Turn the key off, let the engine compartment cool down,
wipe the cap and the top of the reservoir clean, then
unscrew the cap and wipe the dipstick with a clean rag.
Replace the cap and completely tighten it. Then remove
the cap again and look at the fluid level on the dipstick.
The level should be at the FULL COLD mark.
If necessary, add only enough fluid to bring the
level up to the mark.
What to Use
To determine what kind of fluid to use, see
ªRecommended Fluids and Lubricantsº in the Index.
Always use the proper fluid. Failure to use the proper
fluid can cause leaks and damage hoses and seals.