radio CADILLAC ESCALADE 2002 2.G User Guide

3-
3-1
Section 3 Comfort Controls and Audio Systems
In this section, you'll find out how to operate the comfort control and audio systems offered with your vehicle.
Be sure to read about the particular systems supplied with your vehicle.
3
-2 Comfort Controls
3
-2 Electronic Climate Control System
3
-7 Air Conditioning
3
-7 Heating
3
-8 Defogging and Defrosting
3
-8 Rear Window Defogger
3
-9 Ventilation System
3
-10 Audio Systems
3
-11 AM-FM Stereo with Cassette Tape
Player (Bose
)3
-15 Rear Seat Audio (RSA)
3
-17 Compact Disc Changer
3
-20 Theft-Deterrent Feature
3
-22 Audio Steering Wheel Control
3
-23 Understanding Radio Reception
3
-23 Tips About Your Audio System
3
-24 Care of Your Cassette Tape Player
3
-26 Care of Your Compact Discs
3
-26 Care of Your Compact Disc Changer
3
-26 Diversity Antenna

3-11 AM-FM Stereo with Cassette Tape
Player (Bose

)
Included with the AM-FM Stereo with Cassette Tape
Player is a six disc CD changer. It is equipped with
ten Bose

high performance speakers, an Acoustimass

bass module and a seven channel Bose amplifier.
Please see your dealer for details.Playing the Radio
PWR VOL: Press this knob to turn the system on
and off. To increase volume, turn the knob clockwise.
Turn it counterclockwise to decrease volume. The knob
is capable of being turned continuously.
SCV: Your system has a feature called
Speed
-Compensated Volume (SCV). With SCV, your
audio system adjusts automatically to make up for road
and wind noise as you drive. Set the volume at the
desired level. Turn the control ring behind the upper
knob clockwise to adjust the SCV. Then, as you drive,
SCV automatically increases the volume, as necessary,
to overcome noise at any particular speed. The volume
level should always sound the same to you as you drive.
If you don't want to use SCV, turn the control all the
way down. Each notch on the control ring allows for
more volume compensation at faster vehicle speeds.
REAR DSPL: When the main radio is turned on, press
this button to turn on the rear seat audio display on the
main radio. Press it again to turn the rear seat audio
display off.
PR: Press this button to turn rear seat audio on or off.
The light to the right of the button will illuminate to
indicate that rear seat audio is on.

3-12
Finding a Station
AM FM: Press this button to switch between AM, FM1
and FM2. The display will show your selection.
TUNE: Press this knob lightly so it extends. Turn it to
choose radio stations. Push the knob back into its stored
position when you're not using it.
SEEK : To seek, press the right arrow to tune
to the next station and the left arrow to tune to the
previous station and stay there. The sound will mute
while seeking.
To scan, press and hold SEEK for two seconds until
SCAN appears on the display. Scan allows you to
listen to stations for a few seconds. The receiver will
continue to scan and momentarily stop at each station
until you press the button again. The sound will mute
while scanning.
P. SCAN: The preset scan button lets you scan through
your favorite stations stored on your pushbuttons.
Select either the AM, FM1 or FM2 mode and then press
P. SCAN. It will scan through each station stored on
your pushbuttons and stop for a few seconds before
continuing to scan through all of the pushbuttons.Press P. SCAN again or one of the pushbuttons to stop
scanning and listen to a specific preset station. P. SCAN
will light up on the display while in this mode. If one of
the stations stored on a pushbutton is too weak for the
location you are in, the radio display will show the
channel number (P1 through P6) for several seconds
before advancing to the next preset station.
Setting Preset Stations
The six numbered pushbuttons let you return to your
favorite stations. You can set up to 18 stations
(six AM, six FM1 and six FM2) by performing the
following steps:
1. Turn the radio on.
2. Press AM FM to select the band.
3. Tune in the desired station.
4. Press and hold one of the six pushbuttons. The sound
will mute. When it returns, release the pushbutton.
Whenever you press that numbered pushbutton, the
station you set will return.
5. Repeat the steps for each pushbutton.

3-13
Setting the Tone
BASS: Press lightly on this knob to release it from its
stored position. Turn the knob clockwise to increase
bass and counterclockwise to decrease bass.
TREB: Press lightly on this knob to release it from its
stored position. Turn the knob clockwise to increase
treble and counterclockwise to decrease treble. If a
station is weak or noisy, you may want to decrease
the treble.
Push these knobs back into their stored positions when
you're not using them.
Adjusting the Speakers
FADE: Press lightly on this knob to release it from its
stored position. Turn the control clockwise to adjust the
sound to the front speakers and counterclockwise for the
rear speakers. The middle position balances the sound
between the speakers.
BAL: Press lightly on this knob to release it from its
stored position. Turn the control clockwise to adjust
sound to the right speakers and counterclockwise to
adjust sound to the left speakers. The middle position
balances the sound between the speakers.
Push these knobs back into their stored positions when
you're not using them.Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in
this player.
To load a cassette tape with the ignition off, press
EJECT. Then, insert the cassette tape. If the ignition is
on but the radio is off, the tape will begin playing.
Once the tape is playing, use the volume, balance, fade,
bass and treble controls just as you do for the radio. The
tape symbol and a direction arrow will be on the display
whenever a tape is being played. Anytime a tape is
inserted, the top side is selected for play first.
The player automatically senses if the cassette tape is
metal or CrO
2 and adjusts for best playback sound.
1 PREV: Press this button or the SEEK left arrow to
search for the previous selection. A minimum
three
-second blank gap is required for the player to stop
at the beginning of the selection. The tape direction
arrow will blink during the SEEK operation.
2 PROG: Press this button to switch from one side of
the tape to the other.

3-14
3 NEXT: Press this button or the SEEK right arrow to
search for the next selection. A minimum three
-second
blank gap is required for the player to stop at the
beginning of the selection. The tape direction arrow will
blink during the SEEK operation. The sound will mute
while searching for the next selection.
4 REV: Press this button to rapidly reverse the tape to
the beginning of the cassette or until you press REV 4
again. The radio will play the last selected station while
reversing the tape. The tape direction arrow will blink
during the reverse operation.
5
: Press this button to reduce cassette tape noise.
The double
-D symbol will appear on the display while
the player is in this mode.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double
-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
6 FWD: Press this button to rapidly forward the tape to
the end of the cassette or until you press FWD again.
The radio will play the last selected station while
forwarding the tape. The tape direction arrow will blink
during the forward operation.
AM FM: Press this button to switch from a tape to
the radio.TAPE: Press this button to play a tape if you have a tape
loaded in the cassette tape player and the radio is turned
on. When a tape is playing, a lighted arrow will appear
on the display and show the direction of play. If the
radio is turned off, the tape will remain in the player and
resume playing at the point where it stopped.
EJECT: Press this button to remove the tape. The radio
will now play. Eject can be used with either the ignition
or radio off. To load a cassette tape with the ignition or
radio off, press EJECT before loading the cassette.
CHANGER: Press this button to play a CD if you have
a CD loaded in the CD changer. When a CD is playing
the disc number and track number will be displayed.
Press this button again and elapsed time will appear on
the display. See ªCompact Disc Changerº later in
this section.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See ªCare of
Your Cassette Tape Playerº in the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the CLN indicator. The radio will display
--- to
show the indicator was reset.

3-15
CD Adapter Kits
It is possible to use a portable CD player adapter kit
with your cassette tape player after activating the bypass
feature on your tape player.
To activate the bypass feature, perform the
following steps:
1. Turn the ignition to RUN or ACCESSORY.
2. Turn the radio off.
3. Press and hold the TAPE button for five seconds.
The tape symbol on the display will flash for
two seconds, indicating the feature is active.
4. Insert the adapter into the cassette slot. It will power
up the radio and begin playing.
This override routine will remain active until EJECT
is pressed.Rear Seat Audio (RSA)
This feature allows rear seat passengers to listen to and
control any of the music sources, including AM FM,
cassette tapes and CDs, through the Rear Seat Audio
(RSA) controller. However, the rear seat passengers can
only control the music sources that the front seat
passengers are not listening to.

3-16
For example, rear seat passengers may listen to a
cassette tape through headphones while the driver listens
to the radio through the front speakers. The rear seat
passengers have control of the volume for each set of
headphones. Be aware that the front seat audio controls
always have priority over the RSA controls. If the front
seat passengers switch the source for the main radio to a
remote source, the RSA will play the same remote
source. The rear speakers will be muted when the RSA
power is turned on. You may operate the RSA functions
even when the main radio is off.
The following functions are controlled by the buttons on
the main radio:
REAR DSPL: When the main radio is turned on, press
this button to turn on the RSA display on the main radio.
Press it again to turn the RSA display off.
PR: Press this button to turn RSA on or off. The light
to the right of the button will illuminate to indicate that
RSA is on.
The following functions are controlled by the RSA
system buttons:
PWR: Press this button to turn RSA on or off.AM FM: Press this button to switch between AM, FM1
and FM2. If the front passengers are already listening to
AM FM, the RSA controller will not switch between the
bands and cannot change the frequency.
SEEK : While listening to the radio, press the up
arrow to tune to the next station and stay there. Press the
down arrow to tune to the previous station and stay
there. The sound will mute while seeking. The SEEK
button is inactive if the AM FM mode on the front radio
is in use.
While listening to a cassette tape, press the up arrow to
hear the next selection on the tape. Press the down arrow
to go back to the previous selection. The SEEK button is
inactive if the tape mode on the front radio is in use.
While listening to a CD, press the up arrow to hear the
next selection on the CD. Press the down arrow to go
back to the start of the current selection (if more than
eight seconds have played). The SEEK button is inactive
in the CD mode if the CD changer is in use.
Press and hold one of the SEEK arrows until the radio
goes into the scan mode. Scan allows you to listen to
stations for a few seconds. The receiver will continue to
scan and momentarily stop at each station until you press
one of the SEEK arrows again. The scan function is
inactive if the AM FM mode on the front radio is in use.

3-17
VOL: Press this knob lightly so it extends. Turn
the knob clockwise to increase volume and
counterclockwise to decrease volume. Push the knob
back into its stored position when you're not using it.
The upper VOL knob controls the upper headphone and
the lower VOL knob controls the lower headphone.
TAPE CD: Press this button to switch between the tape
and CD changer if all are loaded. Press AM FM to
return to the radio when a cassette tape or CD is playing.
The inactive tape or CD will remain safely inside the
radio for future listening.
P.SET PROG: The front passengers must be listening
to something different for each of these functions
to work:

Press this button to seek through the preset radio
stations set on the pushbuttons on the main radio.

When a cassette tape is playing, press this button to
go to the other side of the tape.

When a CD is playing in the CD changer, press this
button to select a disc.Compact Disc Changer
The compact disc changer plays up to six standard size
CDs continuously. Individual CDs may be loaded into or
ejected from any position.
A green light on each numbered button indicates a CD is
loaded in the respective position. An amber light on a
numbered button indicates that a CD is playing. When
loading CDs, the loading slot indicators turn amber to
indicate that the player is ready to accept a CD. CDs can
be loaded or ejected with the radio or the ignition being
on or off.

3-19
There are two ways to play a CD. Perform one of
the following:

Press the desired numbered button with a green
indicator light on the CD changer.

Press the CHANGER button on the radio. The CD
changer will go to its last played position.
1 PREV: Press this button or the SEEK left arrow to
go to the previous track if the current selection has been
playing for less than eight seconds. If the PREV 1
button is pressed and the current selection has been
playing for more than eight seconds, it will go to the
beginning of the current selection. If you hold or press
this button more than once, the player will continue
moving back through the CD. The sound will mute
while seeking.
2 PROG: Press this button to select a CD. The CD
number and track number will be displayed.
3 NEXT: Press this button or the SEEK right arrow
to go to the next track. If you hold the button or press
it more than once, the player will continue moving
forward through the CD. The sound will mute
while seeking.4 REV: Press and hold this button to reverse quickly
through a track selection. Release it to resume playing.
6 FWD: Press and hold this button to advance quickly
through a track selection. Release it to resume playing.
SEEK :Press the right arrow to seek to the next
selection on the CD. Press the left arrow to search for
the previous selection on the CD. The sound will mute
while seeking.
P.SCAN: Press this button to hear the tracks in random,
rather than sequential, order. DSC will appear on the
radio display, which will randomly play the tracks on the
current CD. Press P.SCAN again to make the radio
display ALL, which will randomly play all loaded CDs.
Press P.SCAN again to turn off random play, OFF will
appear on the radio display.
CHANGER: Press this button if you have a CD
loaded into the changer and the radio is turned on, to
play a CD. Press AM FM to return to the radio when a
CD is playing.

3-20
Compact Disc Changer Errors
If ERR appears on the display, it could be one of
the following:

You are driving on a very rough road. (The CD
should play when the road gets smoother.)

A CD is upside down.

It is dirty, scratched or wet.

It is very humid. (If so, wait about an hour and
try again.)

The CD player is very hot.
Press CHANGER to make ERR turn off the display.
If any error occurs repeatedly or if an error cannot be
corrected, please contact your dealer.
Theft-Deterrent Feature
THEFTLOCK is designed to discourage theft of your
radio. It works by using a secret code to disable all radio
functions whenever battery power is removed.
The THEFTLOCK feature for the radio may be used or
ignored. If ignored, the system plays normally and the
radio is not protected by the feature. If THEFTLOCK is
activated, your radio will not operate if stolen.When THEFTLOCK is activated, the radio will display
LOC to indicate a locked condition anytime battery
power has been interrupted. If your battery loses power
for any reason, you must unlock the radio with the secret
code before it will operate.
Activating the Theft
-Deterrent Feature
The instructions which follow explain how to enter your
secret code to activate the THEFTLOCK system. It is
recommended that you read through all nine steps
before starting the procedure.
If you allow more than 15 seconds to elapse between
any steps, the radio automatically reverts to time and
you must start the procedure over at Step 4.
1. Write down any three or four
-digit number from
000 to 1999 and keep it in a safe place separate from
the vehicle.
2. Turn the ignition to ACCESSORY or RUN.
3. Turn the radio off.
4. Press the 1 and 4 pushbuttons together. Hold them
down until
--- shows on the display. Next you
will use the secret code number which you have
written down.
5. Press the SEEK right pointing arrow button and
000 will appear on the display.