reset CADILLAC ESCALADE ESV 2010 Workshop Manual

Black plate (37,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Overheated Engine Protection
Operating Mode If an overheated engine condition exists and the
ENGINE POWER IS REDUCED message is displayed,
an overheat protection mode which alternates firing
groups of cylinders helps prevent engine damage. In
this mode, you will notice a loss in power and engine
performance. This operating mode allows the vehicle to
be driven to a safe place in an emergency. Driving
extended miles (km) and/or towing a trailer in the
overheat protection mode should be avoided.
Notice: After driving in the overheated engine
protection operating mode, to avoid engine damage,
allow the engine to cool before attempting any
repair. The engine oil will be severely degraded.
Repair the cause of coolant loss, change the oil
and reset the oil life system. See Engine Oil
on
page 7 ‑ 17 . Engine Fan Noise The vehicle has electric cooling fans. You might hear
the fans spinning at low speed during most everyday
driving. The fans can turn off if no cooling is required.
Under heavy vehicle loading, trailer towing, and/or high
outside temperatures, or if you are operating the air
conditioning system, the fans can change to high speed
and you might hear an increase in fan noise. This is
normal and indicates that the cooling system is
functioning properly. The fans change to low speed
when additional cooling is no longer required.
7-37

Black plate (52,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Headlamp Aiming The vehicle has a visual optical headlamp aiming
system. The aim of the headlamps have been preset at
the factory and should need no further adjustment.
However, if the vehicle is damaged in a crash, the aim
of the headlamps may be affected and adjustment may
be necessary.
If oncoming vehicles flash their high beams at you, this
may mean the vertical aim of your headlamps needs to
be adjusted.
It is recommended that the vehicle is taken to your
dealer for service if the headlamps need to be adjusted.
It is possible however, to re-aim the headlamps as
described.
The vehicle should: .
Be placed so the headlamps are 25 ft. (7.6 m) from
a light colored wall or other flat surface. .
Have all four tires on a level surface which is level
all the way to the wall or other flat surface. .
Be placed so it is perpendicular to the wall or other
flat surface. .
Not have any snow, ice, or mud on it. .
Be fully assembled and all other work stopped
while headlamp aiming is being performed. .
Be normally loaded with a full tank of fuel and one
person or 160 lbs (75 kg) sitting on the driver seat. .
Have the tires properly inflated. .
Have the spare tire is in its proper location in the
vehicle.
Headlamp aiming is done with the vehicle's low-beam
headlamps. The high-beam headlamps will be correctly
aimed if the low-beam headlamps are aimed properly.
To adjust the vertical aim:
1. Open the hood. See Hood Release
on page 7 ‑ 15
for more information.
2. Locate the center of
the projector lens of
the low ‐ beam
headlamp.
3. Record the distance from the ground to the center
of the projector lens of the low ‐ beam headlamp.
7-52

Black plate (72,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
Any time you notice unusual wear, rotate your
tires as soon as possible and check wheel
alignment. Also check for damaged tires or
wheels. See When It Is Time for New Tires
on
page 7 ‑ 73
and Wheel Replacement on page 7 ‑ 77 .
When rotating your vehicle's tires, always use the
correct rotation pattern shown here.
Do not include the spare tire in the tire rotation.
After the tires have been rotated, adjust the front
and rear inflation pressures as shown on the Tire
and Loading Information label. See Inflation - Tire
Pressure
on page 7 ‑ 65 and Loading the Vehicle on
page 6 ‑ 32
. Reset the Tire Pressure Monitor System. See Tire
Pressure Monitor Operation
on page 7 ‑ 68 .
Make certain that all wheel nuts are properly
tightened. See “ Wheel Nut Torque ” under
Capacities and Specifications
on page 7 ‑ 117 .
{ WARNING: Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt
from places where the wheel attaches to
the vehicle. In an emergency, you can use
a cloth or a paper towel to do this; but be
sure to use a scraper or wire brush later,
if needed, to get all the rust or dirt off. See
Changing a Flat Tire
on page 7 ‑ 80 .
Make sure the spare tire is stored securely. Push,
pull, and then try to rotate or turn the tire. If it
moves, tighten the cable. See Storing a Flat or
Spare Tire and Tools
on page 7 ‑ 94 .
7-72

Black plate (3,1)Cadillac Escalade/Escalade ESV Owner Manual - 2010
At your dealer, you can be certain that you will receive
the highest level of service available. Your dealer has
specially trained service technicians, uses genuine
replacement parts, as well as, up to date tools and
equipment to ensure fast and accurate diagnostics.
The proper replacement parts, fluids, and lubricants to
use are listed in Recommended Fluids and Lubricants
on page 8 ‑ 10 and Maintenance Replacement Parts on
page 8 ‑ 12
. We recommend the use of genuine parts
from your dealer.
Rotation of New Tires To maintain ride, handling, and performance of the
vehicle, it is important that the first rotation service for
new tires be performed when they have 8 000 to
13 000 km (5,000 to 8,000 miles). See Tire Inspection
and Rotation on page 7 ‑ 71 . Scheduled Maintenance When the Change Engine Oil Soon
Message Displays Change engine oil and filter. See Engine Oil on
page 7 ‑ 17 . An Emission Control Service.
When the Change Engine Oil Soon message displays,
service is required for the vehicle as soon as possible,
within the next 1 000 km/600 miles. If driving under the
best conditions, the engine oil life system might not
indicate the need for vehicle service for more than a
year. The engine oil and filter must be changed at least
once a year and the oil life system must be reset. Your
dealer has trained service technicians who will perform
this work and reset the system. If the engine oil life
system is reset accidentally, service the vehicle within
5 000 km/3,000 miles since the last service. Reset the
oil life system whenever the oil is changed. See Engine
Oil Life System on page 7 ‑ 20 .
When the Change Engine Oil Soon message displays,
certain services, checks, and inspections are required.
8-3