CADILLAC ESCALADE EXT 2002 2.G Owners Manual

2-65
NOTICE:
The cargo covers are designed to support 250 lbs.
(113 kg) each on top of them. Exceeding the
weight limit can damage the cargo covers.
This damage would not be covered by your
vehicle's warranty.
Your vehicle is equipped with a three-piece cargo cover
system. The cargo panels can be removed and stored in the
cargo area of the vehicle with the cargo panel storage bag.
To remove a cargo panel(s), do the following:
1. Lower the tailgate. Use the ignition/door key to
unlock the tailgate if it is locked. See ªTailgateº in
the Index for more information on the tailgate.
Before removing the cargo panel(s), notice the
numbers embossed on the upper center portion of
each panel. The panels are labeled 1, 2 and 3. There
are also numbered labels on the bottom of the panels.
The numbers on the top and bottom of the panels
will be used as reference when removing, storing and
reinstalling the panels.

2-66
2. Remove cargo panel 3 by pulling the left and right
cargo panel latches, located on the bottom of each
cargo panel, toward you to release (unlock) the cargo
panel latches.
3. Pull the cargo panel up and then out from the
side rails and set it aside. You only need to remove
as many cargo panels as needed for your cargo
carrying needs.4. Remove cargo panel 2 in the same way and set
it aside.

2-67
5. Remove cargo panel 1, but notice that there are four
latches to release (two left
-side latches and two-right
side latches). Set the panel aside.
After you have removed each cargo panel you can store
it within the cargo storage area using the cargo panel
storage bag.Cargo Panel Storage System
The three cargo panels can be stored on either the
driver's or passenger's side of the cargo box using the
storage bag. To store the panels, do the following:

2-68
1. Secure the storage bag
in the cargo storage
area by attaching the
four clips on the cargo
bag to the tie
-down
locations on either side
of the storage area.
It is very important that you use the storage bag to
restrain the cargo panels during driving.
Before storing the cargo panels, be sure that the
latches are in the closed (locked) position. The
latches are in the closed (locked) position when they
are parallel to the front and back edge of the panel.
Use the art and following instructions for the proper
storage sequence and location for each panel:
Panels 3, 2, 1 Loaded

2-69
2. Starting with cargo panel 1 (the panel with four
latches), load the cargo panel with latches at the top
of the bag and facing outboard (side of panel with no
latches should be facing you as you load the panel).
3. Store cargo panel 2 by loading the cargo panel with
latches down and facing inboard (side of panel with
latches would be facing you as you load the panel).

2-70
4. Store cargo panel 3 by loading the cargo panel with
latches at the top of the bag and facing outboard
(side of panel with no latches should be facing you
as you load the panel).
5. Zip the bag shut.6. Snug both straps on the bag by pulling on the free
end of the straps.

2-71
7. Close both top and bottom mechanisms at the center
of the bag (bag should now be tightly secured).Reinstalling the Cargo Cover Panels
You only need to reinstall as many cargo panels as you wish.
1. Remove the cargo panel(s) from the storage bag.
You can either leave the bag attached to the side of
the cargo area while it is not in use, or you can store
it outside of the vehicle.
2. Starting with cargo panel 1, place the latches in the
open (unlocked) position. Place cargo panel 1 on the
cargo area rails while holding the back of the cargo
panel up.

2-72
Left Side Shown, Right Side Similar
Push the panel forward until it is snug against the
Midgate and then let the back of the panel down
being sure that the alignment pegs align with the
receivers (see arrow).
3. Push both left latches away from you to lock the
latches (remember that there are two latches on each
side for panel 1). You should hear a click when each
latch locks correctly. Lock the remaining two right
latches on panel 1.
For any cargo cover panel you must lock the left
latch in place before you can lock the right latch. If
you do not follow this exactly, the cargo cover panels
may not lock in place correctly.

2-73
4. Install cargo cover 2 next. Place the latches in the
open (unlocked) position. Place the cargo cover
panel on the cargo area rails while holding the back
of the cargo panel up.
Left Side Shown, Right Side Similar
Push the panel forward until it is snug against the
other panel and then let the back of the panel down
being sure that the alignment pegs align with the
receivers (see arrow).
5. Push the latches away from you (start with the left
latch) to lock the panel in place. You should hear a
click when each latch locks correctly.
6. Install cargo cover 3 next. Place the latches in the
open (unlocked) position. Place the cargo cover
panel on the cargo area rails while holding the back
of the cargo panel up.

2-74
Left Side Shown, Right Side Similar
Push the panel forward until it is snug against the
other panel and then let the back of the panel down
being sure that the alignment pegs align with the
receivers (see arrow).
7. Push the latches away from you (start with the left
latch) to lock the panel in place. You should hear a
click when each latch locks correctly.