reset CADILLAC SEVILLE 1997 4.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine c
c
STOP ENGINE LOW OIL PRESSURE - 35: If this
message appears while the engine is running, stop the
engine and do
!lot operate it until the cause of low oil
pressure
is corrected. Severe damage to the engine can
result.
A nlultiple chime will also sound when this
message is displayed.
THEFT SYSTEM YROBLEWCAR MAY NOT
RESTART
- 34: This message means there is a problem
in the Personalized Automotive Security System
(PASS-Key 11). A fault has been detected in the system
which means thzt the PASS-Key
I1 system is disabled
and is
not protecring the vehicle. The vehicle usually
restarts. however,
you may want to take your vehicle to
a proper service center before turning off the engine.
TOP SPEED FUEL CUT-OFF - 111: This message
will appear when the PCM senses that the maximum
speed
for your Cadillac has been reached. The speed
of your vehicle will decrease several mph as the fuel
supply is cutoff. This allows your vehicle
to stay in a
stable operating range.
TRACTION ENGAGED - 91: When your traction
control system is limiting wheel spin, the TRACTION
ENGAGED message will be displayed. Slippery road
conditions may exist if this message is displayed,
so
adjust your driving accordingly. This message. will stay
on
for a few seconds after the traction control system
stops limiting wheel spin.
TRACTION OFF - 89: This message will be displayed
after the traction control has been turned off.
TRACTION READY - 91: This message informs the
driver that the traction control system is available. This
occurs when
the traction doff button in the glove box
has been returned to an on position (pressing the button
once turns the traction control system
off pressing the
button again turns the system back on). This message
also self cancels after five seconds.
TRACTION SUSPENDED - 56: This message
displays when the traction control system has been
temporarily shut off because your vehicle’s brakes
have overheated. This message
does not indicate a
problem with your vehicle’s traction control system.
After a few minutes, the traction control system will
be available again and
the TRACTION READY
message will appear.
TRANS FLUID RESET - 48: With the engine not
running and the ignition on, press and hold the OFF
and rear defog buttons until the TRANS FLUID
RESET message appears
on the DIC (between five
and 20 seconds).
TRANSMISSION HOT .. 112: This messages indicates
that the transaxle fluid in your vehicle is too hot. Stop
and allow your vehicle to idle until it cools down or
until this message is removed.

Downloaded from www.Manualslib.com manuals search engine The DIC may display a CHECK OIL LEVEL message.
Always keep a written record of the mileage and date
when
you changed your oil. For more information. see
the Cadillac Maintenance Schedule booklet. If you see
CHECK OIL LEVEL,
it means that you have less than
10 percent of the oil life left and you should consider
changing
your engine oil. If you see CHANGE
ENGINE OIL.
it means the oil life is gone and you
should change the oil right away.
The system should indicate changing the
oil between
3,000 miles (5 000 km) and 7,500 miles (12 SO0 km).
It may indicate changing the oil before 3.000 miles
(5 000 lunj depending on your driving habits. If the
vehicle has been driven
7,500 miles (1 2 500 krn), it
, .. . will indicate to change the oil. If you drive in a dusty
area.
you should change your oil every 3,000 miles
This feature lets
you know when to change the engine
oil. It's based on the engine oil temperatures and your
driving patterns.
To see the display, press the
INFORMATION (INFO) button
several times until
XX OIL LIFE LEFT appears. If you see 99% OIL
LIFE LEFT,
99 percent of your current oil life remains.
(5 000 km) or three months (whichever comes first)
unless
the display indicates changing it sooner. The
system doesn't check
im!~ ~?zuc/? oil you have. so you'll
still have to check
for that. To see how, see "Engine Oil"
in the Index.
When new
oil is added, you'll need to reset the system.
To reset. display the Oil. Life Indicator by pressing the
INFORMATION (INFO) button. Then press and hold
the RESET (INFO RESET) button until the display
shows 100% OIL LIFE LEFT.

Downloaded from www.Manualslib.com manuals search engine c
c
c
c
c
The outside temperature is always displayed when your
vehicle
is running. You can change it from Fahrenheit to
Celsius by pressing the INFO button (above the radio)
until ENGLISHMETRIC RESET displays. Once
displayed, press the
INFO RESET button to select.
The outside temperature sensor is located near the front
grille. The sensor
can be affected by road or engine heat
during idling.
slow driving or when the engine 1s first
started after a short trip. In order to ensure proper
automatic climate control operation, the outside air
temperature display may
not update as quickly as
expected. This is to allow the air surrounding the outside
temperature sensor to be as close
to the actual outside
conditions as possible. This is determined by how much
time has elapsed since the vehicle has been turned
off
and by vehicle speed. Press this
button to deliver air through the floor, middle
or windshield outlets. The system will stay
in the
selected mode
until the MODE button is pushed again.
Press the up or clown arrow to cycle through the
available modes.
Aud:a,xmtt:ic~ d)pc1-ai:iornjr
When the system is set for automatic operation, sensors
will control the air delivery mode.
Air will come from
the floor, middle or windshield outlets. The fan speed
will vary as the system maintains the selected
temperature setting.
Be careful not
to put anything over the solar sensor
located in the middle
of the instrument panel near the
windshield. This sensor is used
by the automatic system
to regulate temperature.

Downloaded from www.Manualslib.com manuals search engine I-
C
PWWVOL: Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again to turn the system off. To increase volume,
turn
the knob clockwise. Turn it counterclockwise to
decrease volume. The volume level will appear
on
the display.
DSPL: Press this button to display the station
being played.
BAND: Press this button to select AM. FM 1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to
the next higher or lower radio station. Pressing and
holding this button
until a chime sounds puts the radio in
a tune mode. In this mode, higher or lower radio stations
are advanced
to in small increments until the
SEEK-TUNE button
is released. Tuning stops when you
release this button.
If you press and hold the
SEEK-TUNE button again within five seconds of being
in the tune mode. tuning will continue. Waiting longer
than five seconds places the radio back in the seek mode.
SCAN: Press this button and SCAN will appear on the
display. Use
SCAN to listen to stations for a few
seconds. The radio will
go to a station, stop for a few
seconds, then
go on to the next station. Press this button
again to
stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations.
You can set up to
18 stations (six AM, six FMl and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear
a chime. The sound will mute. When it
returns, release the button. Whenever
you press that
numbered button. the station
you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds
until PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have
not been reprogrammed with
your stations will be ignored). The radio
will go to the
first preset station stored
on your pushbuttons, stop for a
few seconds. then
go on to the next preset station. Press
SCAN again to stop scanning. If a preset station has weak
reception, the radio will
not stop at the preset station.

Downloaded from www.Manualslib.com manuals search engine c
c
c
REV: Press the left arrow to reverse the tape rapidly.
Press it again to return
to playing speed. The radio will
play while the tape reverses and REV will appear on the
display. You may use your station pushbuttons to
tune to
another radio station while
in REV mode.
FF: Press the right a~ow to fast forward to another part of
the tape. Press it again to return to playing speed. The
radio will play while the tape advances and
FF will appear
on the display. You may use your station pushbuttons to
tune
to another radio station while in FF mode.
SEEK-TUNE: Press the right arrow to seek to the next
selection
on the taps. Press the left arrow to search for
the previous selection
on the tape (REP will appear on
the display). Your tape must have at least three seconds
of silence between each selection for SEEK-TUNE to
work. The sound will mute while seeking.
SCAN: Press this button. SCAN FF will appear on the
display until the next selection is found and then SCAN
PLAY will appear on the display. Use SCAN to listen to
selections for
a few seconds. The tape will go to a
selection, stop for a few seconds. then go on to the next
selection. Press
this button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing. (PLAY shows
on the display.)
SOURCE: Press this button to switch from radio to
cassette tape play. If
no cassette tape is in the tape
player, CASS appears on the display and then the radio
station appears briefly. The display then reverts back
to
showing the time of day. Press this button again or
BAND to switch back to the radio.
4L EJECT Press the upward triangle button to
remove a tape. The radio will play. Eject may be
activated with the radio off. Cassette tapes may be
loaded with the radio off but they will not start playing
until the PWR button is pressed. Press PWR or turn the
ignition key off to stop the cassette tape player. The tape
will stay
in the player and resume play at the point
where it stopped. If you leave a cassette tape
in the
player while listening to the radio,
it may become warm.
CLN: If this message appears on the display. the
cassette tape player needs to be cleaned.
It will still play
tapes, but you should clean it as
soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tdpe Player”
in the Index. After you clean
the player. press and hold EJECT for five seconds
to
reset the CLN indicator. The radio will display --- to
show the indicator was reset.
Dolby’“’ Noise Reduction
is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation.

Downloaded from www.Manualslib.com manuals search engine e
For information on the compact disc player, see “Trunk
Mounted
CD Changer” later in this section.
PWWOL: Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again to turn the system
off. To increase volume, turn the
knob clockwise. Turn it counterclockwise to decrease
volume. The volume level will appear on the display.
BAND: Press this button to select AM, FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to
the next higher or lower radio station. Pressing
and
holding this button until a chime sounds puts the radio in
a tune mode.
In this mode, higher or lower radio stations
are advanced to in small increments
until the
SEEK-TUNE button is released. Tuning stops when you
release this button. If you press and hold the
SEEK-TUNE button again within five seconds of’ being
in the tune mode, tuning will continue.
Waiting longer
than five seconds places the radio back
in the seek mode.
SCAN: Press this button and SCAN will appear on the
display. Use
SCAN to listen to stations for a few
seconds. The radio will go to a station, stop for a few
seconds, then go on to the next station. Press this button
again to stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
18 stations (six AM, six FMl and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.

Downloaded from www.Manualslib.com manuals search engine c-
c
4. Press and hold one of the six numbered buttons until
you hear a chime.
A preset number will appear on
the display. The sound will mute. When it returns,
release the button. Whenever you press that
numbered button, the station
you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds until
PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have not been reprogrammed with
your stations will be ignored). The radio will
go to the first
preset station stored
on your pushbuttons, stop for a few
seconds, then go
on to the next preset station. Press SCAN
again to stop scanning. If a preset station has weak
reception, the radio will not stop at the preset station.
&&$ixxg; $-$kt: 'j.'$'Elfe.
BASS: Press this knob lightly so it extends. Turn the
knob clockwise
to increase and counterclockwise to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease treble.
If a station is weak or noisy, you may
want
to decrease the treble.
Push these knobs back into their stored positions when
you're
not using them.
BAL: Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to the right speakers and
counterclockwise
for the left speakers. The middle
position balances the
sound hctvieen thc speakers.
FADE: Press this knob lightly so it c'stt'ncis. Turn the
knob clockwise
to adjust the sound to thc front speakers
and counterclockwise
for the rear spcakcr3. The middle
position balances the
sound httwcten thc spcrkers.
Push these knobs back
into their stored positions when
you're not using them.
With the radio on,'insert
a cassette tape. The tape will
begin playing as
soon as it is inserted.
While the tape is playing, use the
VOL, FADE. BAL,
BASS and TREB controls just as you do for the radio.
Other controls may have different functions when a tape
is inserted. The display will show TAPE with an arrow
to indicate which side of the tape is playing. PLAY will
appear on the display temporarily when a tape is
playing.
The display will then revert back to showing
the time.

Downloaded from www.Manualslib.com manuals search engine r
f
r
f
r
r
r
A EJECT Press the upward triangle button to
remove a tape. The radio will play. Eject may be
activated with the radio
off. Cassette tapes may be
loaded with the radio
off but they will not start playing
until the PWR button is pressed.
Press PWR or turn the
ignition key off to stop the cassette tape player. The tape
will stay in the player and resume play
at the point
where it stopped.
If you leave a cassette tape in the
player while listening to the radio, it may become warm.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean
it as soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tape Player” in the Index. After you clean
the player, press and hold EJECT for five seconds
to
reset the CLN indicator. The radio will display --- to
show the indicator was reset.
Dolby“ Noise Reduction is manufactured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation. For information
on the compact disc player, see “Trunk
Mounted
CD Changer” later in this section.
PWRNOL: Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again
to turn the system off. To increase volunle, turn the
knob clockwise.
Turn it counterclockwise to decrease
volume. The
volume level will appear on the display.

Downloaded from www.Manualslib.com manuals search engine 3. Tune in the desired station.
BAND: Press this button to select Ah4. FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to the
next higher or lower radio station. Pressing and holding
this button until a chime sounds puts the radio in a tune
mode. In this mode. higher or lower radio stations are
advanced
to in small increments until the SEEK-TUNE
button is released. Tuning stops when you release this
button. If
you press and hold the SEEK-TUNE button
again within five seconds of being in the tune mode,
tuning will continue. Waiting longer than five seconds
places the radio back in the seek mode.
SCAN: Press this button and SCAN will appear on the
display.
Use SCAN to listen to stations for a few
seconds. The radio will
go to a station, stop for a few
seconds, then
go on to the next station. Press this button
again to stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
I8 stations (six AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FMl or FM2.
4. Press and hold one of the six numbered buttons until
you hear a chime.
A preset number will appear on
the display. The sound will mute. When it returns,
release
the button. Whenever you press that
numbered button,
the station you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hoId SCAN for two to three
seconds
until PRESET SCAN appears on the display to
listen to each of your prcset stations for a few seconds
(factoly presets which have
not been reprogrammed with
your stations will be ignored).
The radio will go to the first
preset station stored
on your pushbuttons, stop for a few
scconds,
then go on to.the next preset station. Press SCAN
again to stop scanning. If a preset station has weak
reception. the radio will not stop at the preset station.
Settirag
the Torre
BASS: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob clockwise
to increase and counterclockwise to
decrease treble. If
a station is weak or noisy, you may
want to decrease the treble.

Downloaded from www.Manualslib.com manuals search engine c
k
c
SOURCE: Press this button to switch from radio to
cassette tape play.
If no cassette tape is in the tape
player,
CASS appears on the display and then the radio
station appears briefly. The display then reverts back to
showing the time of day. Press this button again or
BAND to switch back to the radio.
A EJECT Press the upward triangle button to remove
a tape. The radio will play. Eject may be activated with the
radio
off if the ignition is on. Cassette tapes may be loaded
with
the radio off but they will not start playing until the
PWR button is pressed. Press
PWR or turn the ignition
key
off to stop the cassette tape player. The tape will stay
in the player and resume play at the point where it
stopped.
If you leave a cassette tape in the player while
listening to the radio,
it may become warm.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned.
It will still play
tapes, but
you should clean it as soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tape Player’’ in the Index. After you clean
the player, press and hold
EJECT for five seconds to
reset the
CLN indicator. The radio will display --- to
show the indicator was reset.
Dolby@ Noise Reduction
is manufxtured under a
license from Dolby Laboratories Licensing Corporation.
Dolby and
the double-D symbol are trademarks of
Dolby Laboratories Licensing Corporation. With the compact disc changer,
you can play up to
12 discs continuously. Normal size discs may be played
using the trays supplied in the magazine. The small discs
(8 cm) can be played only with specially designed trays.
NOTICE:
Objects in the trunk which mag shift or slide
during driving could damage your
CD changer.
Protect your
CD changer by using the
convenience net whenever possible. Place large
objects in the trunk appropriately
so that they
will not come into contact with the
CD changer.
,