clock CADILLAC SEVILLE 1997 4.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine To install the storage system:
1.
2.
3.
4.
5.
6.
7.
Pull the carpeting from the floor of the trunk. Turn
the retainer (center dial) on the compact spare tire
cover counterclockwise
to remove it.
Place the trunk storage system on the center of the
trunk floor (the cut
out portion of the storage system
should be facing the rear
of the vehicle).
Open the storage system by pulling up on the handle
located in the carpeted area. This allows the unit to
snap into place. Fold the divider walls open.
Remove
the rectangular access panel from the floor
of the storage system. The access panel should
unsnap by hand.
Center
the storage system access hole over the area
where the spare tire is secured by the retainer.
Position the storage systetn as needed and then
secure it with the retainer.
Replace
the access panel.
Attach the removable
net to the slots located on the
side and front
of the divider walls.
Once in place. the storage system can be moved forward
or rearward for convenience and easy accessing of
stored items. The
following steps explain
how to remove the trunk
storage system
for cleaning or in case you need to access
the spare tire. Follotv all of these steps if the storage
system is in the closed position. Begin with Step
2 if
the system is already open.
1.
2.
3.
4.
Open the storage system by pulling up on the handle
located in the carpeted area. This allows the unit
to
snap into place. Fold the divider walls open.
Remove the rectangular access panel from the floor
of the storage system. The access panel should
unsnap
by hand.
Center the storage system access hole over the
area where the spare tire
is secured by the
retainer. Position the storage system as needed
and then remove the retainer (turn the retainer
counterclockwise
to remove it).
Replace the access panel and remove the
storage system.

Downloaded from www.Manualslib.com manuals search engine c
Only the driver’s side outside mirror will adjust for the
glare of headlamps behind you. This feature is controlled
by the
on and off settings on the electrochromic mirror.
See “Electrochromic Daymight Rearview Mirror” earlier
in this section.
Your passenger’s side mirror is convex.
A convex
mirror‘s surface is curved
so you can sce more from
the driver’s seat. This mirror does not have a
dimming feature.
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could
hit a vehicle on your right. Check your
inside mirror
or glance over your shoulder before
changing lanes.
The glove box is located in front of the passenger’s seat.
To lock the glove box door. insert the oval key into the
lock cylinder and turn
it clockwise. Turn the key
counterclockwise
to unlock the door.

Downloaded from www.Manualslib.com manuals search engine DISPLAY ON/OFF: Pressing this button will turn off
the DIC, Electronic Climate Control (ECC). fuel data
center, the fuel gage. trip odometer- and odometer.
While
the displays are off, pressing the INFORMATION
button will only turn on the DIC. If the TRIP SET
button is pressed or the fuel level falls below fout-
e aallons (15.2 L), all of the displays will come back on.
ENG/MER You can change the display from English
(miles) to metric (kilometers) by pressing
this button.
The same button
also changes other readings (like
temperature, fuel and odometer).
TRIP SET By using this button. you can tcll how Far
you've gone since you last sct t11c TRIP SET back to
zero. To reset, press and hold thc button until XI-OS
appear. If your vehicle is domestic. the trip odonwrcr
will return to zero after 999.9 mi Ics ( I 009 km). I I' !XNII-
vehicle is Canadian, the trip odcmctcr will return lo zero
after 1 999.9 km (1,242 miles ).
INFORMATION: Pressing this button repcatccll), ivill
display the MPG AVG, MPG INST. GAL FUEL LJSED,
AVG MPH, ENGINE RPM. BATTERY VOLTS.
COOLANT TEMP and OIL LIFE LEFT.
TIMER: This feature is like a stopwatch, in that you
can clock the time it takes to get from one point to
another.
To operate, press the TIMER button
until TIMER OFF
0O:OO:OO is displayed on the DIC. Each of the fields for
the hours, minutes and seconds are two numeric digits.

Downloaded from www.Manualslib.com manuals search engine TRIP RESET: By using this button, you can tell how
far you’ve gone since you last set the ?‘RIP
RESET back
to zero. To reset, press and hold the button until zeros
appear.
If your vehicle is domestic. the trip odometer
will return to zero after 999.9 miles
(1 609 km). If your
vehicle is Canadian. the trip odometer will return to
zero after
1 999.9 km ( 1,242 nliles).
INFO RESET Pressing this button will reset the MPG
AVG, GAL FUEL USED, AVG MPH, TIMER, OIL
LIFE LEFT and ENGLISWMETRIC RESET. Pressing
INFO RESET when a non-resettable display appears
will cause a “recall” mode to occur. When this happens,
all DIC waning messages that have been displayed
since the ignition key was turned to RUN will redisplay.
If no messages were displayed, a MONITORED
SYSTEMS
OK message will appear.
MPG AVG (Reset): Press the INFO button to display
the
MPG AVG (Average Fuel Economy), then press
and hold the
INFO RESET button until 0.0 MPG AVG
is displayed.
GAL FUEL USED (Reset): Press the INFO button to
display the
FUEL USED on the DIC, then press and
hold the INFO RESET button until
0.0 GAL FUEL
USED is displayed.
AVG MPH (Reset): Press the INFO button to display
the
AVG MPH (Average Speed), then press and hold the
INFO
RESET button until 0.0 AVG MPH is displayed.
TIMER: This feature is like a stopwatch, in that
you can clock the time
it takes to get from one point
to another.
To operate, press the INFO button to display TIMER.
Each of the fields for the hours, minutes and seconds
are two numeric digits.
Once TIMER
OFF 0O:OO:OO is displayed, press the
INFO RESET button to start the timing feature. Press
the
INFO RESET button again to stop it. If you will be
starting and stopping your Cadillac, during
a trip for
instance, the TIMER feature will automatically start
timing where it
left off when you last stopped. To reset
it, press and hold the lNFO RESET button until the
display reads TIMER
0O:OO:OO. Press the INFO button
to
exit from the TIMER function.
1

Downloaded from www.Manualslib.com manuals search engine c
c In this section, you'll find out how to operate the comfort control and audio systems offctd with our Cdiilac. Be
sure
to read about the particular systems supplied with your vehicle.
c
c
c
3-2
3-2
3 -6
3-7
3-7
3-7
3-9
3-9
3-10
3-10
3-10
3-
10
3-a
Comfort Controls
Climate Control Panel
Electronic
Solar Sensor
Air Conditioning
Heating
Ventilation System
Defrosting
Rear Window Defogger
HVAC Steering Wheel Controls
Climate Control Personalization
Audio Systems
Setting the
Clock
AM-FM Stereo with Cassette Tape Player and
Optional Compact Disc
Player
3- 17
3-2 1
3-25
3-25
3-25
3-26
3-26
3-27
3-28
3-28
3-14 Bose'" AM-Fh;? Stcrco v:ith C''l3hctte Tape
and Compact
Disc Play-
Boss T"' AM-FM Stereo with C'wctte
TT'ape and Compact Disc Pl;~yc.~- with Digital
Signal Processing
Trunk Mounted
CD Changer
Radio Personalization
Theft-Deterrent Feature
Audio Steering Wheel Controls
Understanding Radio Reception
Tips About Your Audio System
Care
of Your Cassette Tape Player
Care
of Your Compact Discs
Power Antenna Mast Care
c 3-:1

Downloaded from www.Manualslib.com manuals search engine This section tells you how to make your air system work
for
you. Your Electronic Climate Control (ECC) system
uses ozone-friendly
R- 134a refrigerant.
With the
ECC system. you can control the heating,
cooling and ventilation in your Cadillac. Your vehicle
also has a flow-through ventilation system described
later
in this section. The
button with the fan symbol adjusts the fan speed.
Press the up arrow to increase fan speed and the down
arrow to decrease fan speed.
The TEMPIAUTO knob adjusts the air temperature
coming through the system. Turn the TEMP/AUTO
knob clockwise to increase the temperature and
counterclockwise to decrease the temperature. Press
the
TEMWAUTO knob to put the system in the
automatic mode.
With this dual-zone feature, the right front passenger can
control the temperature
of air for hidher own zone. The
passenger can select a four degree warmer or cooler
temperature from the driver's setting.
To turn the system
on, press the PASSTEMP button. Press the up arrow to
increase the temperature and press the down arrow to
decrease
the climate setting. Pressing the OFF button
will
turn off the dual-zone function.

Downloaded from www.Manualslib.com manuals search engine With this feature, your vehicle will recall the latest
climate control settings
as adjusted the last time your
vehicle was operated. Thjs feature. allows two different
drivers to store and recall their own climate control
settings. The settings recalled by the climate control
system are determined
by which RKE transmitter (“1”
or “2“) was used to enter the vehicle. The number on the
back of the
RKE transmitter corresponds to driver 1 or
to driver
2. After the unlock button is pressed on the
RKE transmitter or the ignition key is placed in the
ignition, the climate control settings will automatically
adjust
to where they were last set. The settings can also
be changed by briefly pressing the memory seat buttons
1 or 2 located on the driver’s door.
i,C) ~~~~~~~~~.~ 5’
Your Cadillac audio system has been designed to operate
easily and give years of listening pleasure.
You will get
the most enjoyment
out of it if you acquaint yourself with
it first. Find out what
your audio system can do and how
to operate all its controls, to be sure you’re getting the
most out of the advanced engineering that went into
it.
Press and hold HR or MN until the time display begins
to change. Release
the button as you get close to the
correct time. The time may be
set anytime the clock is
displayed. There is a two-second delay before the clock
goes into time-set mode.
For information on the compact disc player, see “Trunk
Mounted
GD Changer” later in this section.
-.
.d

Downloaded from www.Manualslib.com manuals search engine I-
C
PWWVOL: Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again to turn the system off. To increase volume,
turn
the knob clockwise. Turn it counterclockwise to
decrease volume. The volume level will appear
on
the display.
DSPL: Press this button to display the station
being played.
BAND: Press this button to select AM. FM 1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to
the next higher or lower radio station. Pressing and
holding this button
until a chime sounds puts the radio in
a tune mode. In this mode, higher or lower radio stations
are advanced
to in small increments until the
SEEK-TUNE button
is released. Tuning stops when you
release this button.
If you press and hold the
SEEK-TUNE button again within five seconds of being
in the tune mode. tuning will continue. Waiting longer
than five seconds places the radio back in the seek mode.
SCAN: Press this button and SCAN will appear on the
display. Use
SCAN to listen to stations for a few
seconds. The radio will
go to a station, stop for a few
seconds, then
go on to the next station. Press this button
again to
stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations.
You can set up to
18 stations (six AM, six FMl and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear
a chime. The sound will mute. When it
returns, release the button. Whenever
you press that
numbered button. the station
you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds
until PRESET SCAN appears on the display to
listen to each of your preset stations for a few seconds
(factory presets which have
not been reprogrammed with
your stations will be ignored). The radio
will go to the
first preset station stored
on your pushbuttons, stop for a
few seconds. then
go on to the next preset station. Press
SCAN again to stop scanning. If a preset station has weak
reception, the radio will
not stop at the preset station.

Downloaded from www.Manualslib.com manuals search engine BASS: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise
to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob Clockwise to increase and counterclockwise to
decrease treble.
If a station is weak or noisy, you may
want to decrease the treble.
Push these knobs back into their stored positions when
you’re
not using them.
BAL: Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to
the right speakers and
counterclockwise
for the left speakers. The middle
position balances the sound between the speakers.
FADE: Press this knob lightly so it extends. Turn the
knob clockwise to adjust
the sound to the front speakers
and counterclockwise for
the rear speakers. The middle
position balances
the sound between the speakers.
Push these knobs back into their stored positions when
you’re
not using them. With
the radio on, insert a cassette tape. The tape will
begin playing as
soon as it is inserted.
While the tape is playing, use the
VOL, FADE, BAL,
BASS and TREB controls just as you do for the radio.
Other controls may have different functions when a tape
is inserted. The display will show
TAPE with an arrow
to indicate which side of the tape is playing. PLAY will
appear on the display temporarily when
a tape is
playing. The display will then revert back to showing
the time.
If an error occurs while trying to play a cassette tape, it
could be that:
0 The cassette tape is tight and the cassette player
cannot turn the hubs
of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with
a pencil. Flip the tape
over and repeat.
If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used
in the player. Try a new tape to be sure your
player is working properly.
The cassette tape is broken. (Check to see if your
tape
is broken. Try a new tape.)

Downloaded from www.Manualslib.com manuals search engine e
For information on the compact disc player, see “Trunk
Mounted
CD Changer” later in this section.
PWWOL: Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again to turn the system
off. To increase volume, turn the
knob clockwise. Turn it counterclockwise to decrease
volume. The volume level will appear on the display.
BAND: Press this button to select AM, FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to
the next higher or lower radio station. Pressing
and
holding this button until a chime sounds puts the radio in
a tune mode.
In this mode, higher or lower radio stations
are advanced to in small increments
until the
SEEK-TUNE button is released. Tuning stops when you
release this button. If you press and hold the
SEEK-TUNE button again within five seconds of’ being
in the tune mode, tuning will continue.
Waiting longer
than five seconds places the radio back
in the seek mode.
SCAN: Press this button and SCAN will appear on the
display. Use
SCAN to listen to stations for a few
seconds. The radio will go to a station, stop for a few
seconds, then go on to the next station. Press this button
again to stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return
to your favorite stations. You can set up to
18 stations (six AM, six FMl and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FM1 or FM2.
3. Tune in the desired station.