washer fluid CADILLAC SRX 2007 1.G Owners Manual

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The windshield washer button is located at the
end of the windshield wiper lever.
K(Washer Fluid):Press this button to wash
the windshield. Washer uid will squirt onto
the windshield and the wipers will run for a few
cycles to clear the windshield. For more wash
cycles, press and hold the button.If your vehicle is low on washer uid, the WASHER
FLUID LOW ADD FLUID message will appear
on the Driver Information Center (DIC) display.
SeeDIC Warnings and Messages on page 220for
more information.
If the headlamps are on when you wash the
windshield, the headlamp washer will turn on, if
your vehicle has them. Both the windshield and the
headlamps will be washed. SeeHeadlamp
Washer on page 173.
171

Rear Window Wiper/Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
The switch for the rear
washer/wiper is located
in the overhead
console.
Z(Rear Wiper):Press this side of the button to
turn the rear wiper on.
Y(Washer Fluid):Press this button to wash
and wipe the window.
The rear window washer uses the same uid
bottle as the windshield washer. However, the rear
window washer will run out of uid before the
windshield washer. If you can wash your
windshield but not your rear windows, check the
uid level.
5(Delay):Press this side of the button to turn
on delayed wiping.
To turn either the delay or rear wiper setting off,
press the opposite side of the button to turn it
to the off position. Pressing the button all the way
down on either side will activate a wiper setting.
172

WASHER FLUID LOW ADD FLUID
This symbol appears
with this message.
This message displays when your vehicle is low
on windshield washer uid. Rell the windshield
washer uid reservoir as soon as possible.
SeeWindshield Washer Fluid on page 380for
more information.
DIC Vehicle Customization
Your vehicle has customization capabilities that
allow you to program certain features to one
preferred setting. Customization features can only
be programmed to one setting on the vehicle
and cannot be programmed to a preferred setting
for two different drivers.
All of the customization options may not be
available on your vehicle. Only the options
available will be displayed on your DIC.The customization features were set to the default
settings when your vehicle left the factory, but
they may have been changed from their default
state since that time.
The customization preferences are automatically
recalled.
To change customization preferences, use the
following procedure.
Entering the Feature Settings Menu
1. Turn the ignition on and place the vehicle in
PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press the customization button to enter the
feature settings menu.
If the menu is not available, FEATURE
SETTINGS AVAILABLE IN PARK will display.
Before entering the menu, make sure the
vehicle is in PARK (P).
231

Before changing lanes, check your mirrors. Then
use your turn signal.
Just before you leave the lane, glance quickly
over your shoulder to make sure there is not
another vehicle in your blind spot.
Once you are moving on the freeway, make
certain you allow a reasonable following distance.
Expect to move slightly slower at night.
When you want to leave the freeway, move to the
proper lane well in advance. If you miss your
exit, do not, under any circumstances, stop and
back up. Drive on to the next exit.
The exit ramp can be curved, sometimes quite
sharply. The exit speed is usually posted.
Reduce your speed according to your
speedometer, not to your sense of motion. After
driving for any distance at higher speeds, you may
tend to think you are going slower than you
actually are.Before Leaving on a Long Trip
Make sure you are ready. Try to be well rested. If
you must start when you are not fresh — such
as after a day’s work — do not plan to make too
many miles that rst part of the journey. Wear
comfortable clothing and shoes you can easily
drive in.
Is your vehicle ready for a long trip? If you keep it
serviced and maintained, it is ready to go. If it
needs service, have it done before starting out. Of
course, you will nd experienced and able
service experts in GM dealerships all across North
America. They will be ready and willing to help
if you need it.
Here are some things you can check before a trip:
Windshield Washer Fluid:Is the reservoir
full? Are all windows clean inside and outside?
Wiper Blades:Are they in good shape?
Fuel, Engine Oil, Other Fluids:Have you
checked all levels?
Lamps:Are they all working? Are the lenses
clean?
313

Service........................................................ 346
Accessories and Modications................... 347
California Proposition 65 Warning.............. 347
Doing Your Own Service Work.................. 348
Adding Equipment to the Outside of
Your Vehicle.......................................... 348
Fuel............................................................. 349
Gasoline Octane........................................ 349
Gasoline Specications.............................. 350
California Fuel........................................... 350
Additives................................................... 350
Fuels in Foreign Countries........................ 351
Filling the Tank......................................... 352
Filling a Portable Fuel Container............... 354
Checking Things Under the Hood.............. 354
Hood Release........................................... 355
Engine Compartment Overview.................. 356
Engine Oil................................................. 360
Engine Oil Life System.............................. 363
Engine Air Cleaner/Filter............................ 365Automatic Transmission Fluid.................... 367
Engine Coolant.......................................... 368
Coolant Surge Tank Pressure Cap............ 371
Engine Overheating................................... 372
Overheated Engine Protection
Operating Mode..................................... 374
Cooling System......................................... 374
Power Steering Fluid ................................. 379
Windshield Washer Fluid........................... 380
Brakes...................................................... 381
Battery...................................................... 385
Jump Starting............................................ 386
All-Wheel Drive........................................... 392
Rear Axle.................................................... 394
Front Axle................................................... 395
Bulb Replacement....................................... 396
High Intensity Discharge (HID) Lighting..... 396
Halogen Bulbs........................................... 396
Windshield Wiper Blade Replacement....... 397
Section 5 Service and Appearance Care
343

A. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 455.
B. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 380.
C. Battery. SeeBattery on page 385.
D. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 195.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 379.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 360.G. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 360.
H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 381.
I. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 371andCooling System on page 374.
J. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 365.
357

A. Underhood Fuse Block. SeeUnderhood Fuse
Block on page 455.
B. Battery. SeeBattery on page 385.
C. Passenger Compartment Air Filter. See
Passenger Compartment Air Filter on page 195.
D. Windshield Washer Fluid Reservoir. See
“Adding Washer Fluid” underWindshield
Washer Fluid on page 380.
E. Power Steering Fluid Reservoir. SeePower
Steering Fluid on page 379.
F. Engine Oil Fill Cap. See “When to Add Engine
Oil” underEngine Oil on page 360.G. Engine Oil Dipstick (Out of View). See
“Checking Engine Oil” underEngine Oil on
page 360.
H. Brake Master Cylinder Reservoir. See “Brake
Fluid” underBrakes on page 381.
I. Engine Coolant Surge Tank and Pressure Cap.
SeeCoolant Surge Tank Pressure Cap on
page 371andCooling System on page 374.
J. Engine Air Cleaner/Filter. SeeEngine Air
Cleaner/Filter on page 365.
359

How to Check Power Steering Fluid
To check the power steering uid, do the following:
1. Turn the key off and let the engine
compartment cool down.
2. Wipe the cap and the top of the reservoir clean.
3. Unscrew the cap and wipe the dipstick with a
clean rag.
4. Replace the cap and completely tighten it.
5. Remove the cap again and look at the
uid level on the dipstick.
The level should be within the HOT mark. If
necessary, add only enough uid to bring the level
within the mark.
What to Use
To determine what kind of uid to use, see
Recommended Fluids and Lubricants on page 480.
Always use the proper uid. Failure to use the
proper uid can cause leaks and damage hoses
and seals.
Windshield Washer Fluid
What to Use
When you need windshield washer uid, be sure to
read the manufacturer’s instructions before use. If
you will be operating your vehicle in an area where
the temperature may fall below freezing, use a uid
that has sufficient protection against freezing.
Adding Washer Fluid
The WASHER FLUID LOW ADD FLUID message
will appear on the Driver Information Center (DIC)
when the uid level is low. SeeDIC Warnings and
Messages on page 220for more information.
Open the cap with the
washer symbol on it.
Add washer uid
until the tank is full. See
Engine Compartment
Overview on page 356
for reservoir location.
380

Notice:
When using concentrated washer uid,
follow the manufacturer’s instructions
for adding water.
Do not mix water with ready-to-use washer
uid. Water can cause the solution to
freeze and damage your washer uid tank
and other parts of the washer system.
Also, water does not clean as well
as washer uid.
Fill your washer uid tank only
three-quarters full when it is very cold.
This allows for expansion if freezing
occurs, which could damage the tank if it
is completely full.
Do not use engine coolant (antifreeze) in
your windshield washer. It can damage
your washer system and paint.
Brakes
Brake Fluid
Your brake master
cylinder reservoir is
lled with DOT-3 brake
uid. SeeEngine
Compartment Overview
on page 356for the
location of the reservoir.
There are only two reasons why the brake uid
level in the reservoir might go down. The rst
is that the brake uid goes down to an acceptable
level during normal brake lining wear. When
new linings are put in, the uid level goes back
up. The other reason is that uid is leaking out of
the brake system. If it is, you should have your
brake system xed, since a leak means that
sooner or later your brakes will not work well, or
will not work at all.
381

Notice:It is important to check the engine oil
regularly and keep it at the proper level.
Failure to keep the engine oil at the proper
level can cause damage to the engine not
covered by your warranty.
Engine Coolant Level Check
Check the engine coolant level and add
DEX-COOL®coolant mixture if necessary. See
Engine Coolant on page 368for further details.
Windshield Washer Fluid Level Check
Check the windshield washer uid level in
the windshield washer uid reservoir and add the
proper uid if necessary.
At Least Once a Month
Tire Ination Check
Visually inspect your vehicle’s tires and make
sure they are inated to the correct pressures.
Do not forget to check the spare tire. See
Ination - Tire Pressure on page 407. Check to
make sure the spare tire is stored securely.
SeeChanging a Flat Tire on page 424.
At Least Once a Year
Starter Switch Check
{CAUTION:
When you are doing this inspection, the
vehicle could move suddenly. If the
vehicle moves, you or others could be
injured.
1. Before you start, be sure you have enough
room around the vehicle.
2. Firmly apply both the parking brake and the
regular brake. SeeParking Brake on
page 127.
Do not use the accelerator pedal, and be
ready to turn off the engine immediately if
it starts.
3. Try to start the engine in each gear. The
vehicle should start only in PARK (P) or
NEUTRAL (N). If the vehicle starts in any
other position, contact your GM Goodwrench
®
dealer for service.
477