lock CADILLAC STS 2007 1.G Workshop Manual

To program the vehicle to a different mode, use
the following procedure:
1. Enter the PERSONAL SETTINGS MENU by
following the instructions listed previously
under “Entering the Personal Settings Menu.”
2. Turn the tune/select knob until KEYLESS
DOORS UNLOCK is highlighted.
3. Press the tune/select knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
LOCK DELAY
This feature delays the locking of the vehicle’s
doors for eight seconds after a power door
lock switch or the lock button on the keyless
access transmitter is pressed. The eight second
delay occurs after the last door is closed. If
the keyless access transmitter is left inside of the
vehicle, the doors will not lock.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the PERSONAL SETTINGS MENU by
following the instructions listed previously
under “Entering the Personal Settings Menu.”
2. Turn the tune/select knob until LOCK DELAY
is highlighted.
3. Press the tune/select knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
165

KEYLESS LOCK DELAY
This feature allows you to select whether the
doors automatically lock during normal vehicle exit.
When the ignition is turned off and all doors
become closed, the vehicle will determine how
many keyless access transmitters remain in
the vehicle interior. If at least one keyless access
transmitter has been removed from the interior
of the vehicle, the doors will lock after 10 seconds.
For example, if there are two keyless access
transmitters in the vehicle and one is removed, the
other will be locked in. The keyless access
transmitter locked in the vehicle can still be used
to start the vehicle or unlock the doors, if
needed. A person approaching the outside of the
locked vehicle without an authorized keyless
access transmitter, however, will not be able to
open the door, even with a transmitter in the
vehicle.
You may temporarily disable the passive door
locking feature by pressing the door unlock switch
for three seconds on an open door. Passive
door locking will then remain disabled until a door
lock switch is pressed or until the power mode
transitions from the off power mode.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the PERSONAL SETTINGS MENU by
following the instructions listed previously
under “Entering the Personal Settings Menu.”
2. Turn the tune/select knob until KEYLESS
LOCK DELAY is highlighted.
3. Press the tune/select knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
166

FRONT PASS (Passenger) WINDOW LOCK
This feature allows you to choose whether or
not to have the front passenger window
deactivated as part of the window lockout button.
If you would like the front passenger window
to be deactivated when the window lockout button
is pushed, turn this feature on. If this feature is
left off, the window lockout button located on the
door will deactivate only the rear windows.
SeePower Windows on page 105for more
information.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the PERSONAL SETTINGS MENU by
following the instructions listed previously
under “Entering the Personal Settings Menu.”2. Turn the tune/select knob until FRONT PASS
WINDOW LOCK is highlighted.
3. Press the tune/select knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
CHIME VOLUME HIGH
This feature allows you to adjust the volume level
of the vehicle’s warning chimes. The chime
volume cannot be turned off, only adjusted.
Programmable Modes
Mode 1:NORMAL
Mode 2:HIGH
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
167

Driver Selection Submenu Items
DRIVER 1/DRIVER 2
The numbers on the back of each keyless access
transmitter correspond to DRIVER 1 and
DRIVER 2. If you would like to recall or store
driver settings for the driver that does not
correspond to the number on the back of the
keyless access transmitter that you are using,
use the following procedure:
1. Enter the memory programming mode for
your driver settings by following the
instructions listed previously under “Entering
the Driver Selection Submenu.”
2. From the DRIVER SELECTION submenu,
turn the tune/select knob to highlight the
driver number that you want, either DRIVER 1
or DRIVER 2.
3. Set your choice by pressing in the
tune/select knob.
If you would like to recall or store driver settings for
the selected driver, see “RECALL DRIVER
SETTINGS” or “STORE DRIVER SETTINGS”
later in this section.
If you would like to recall or store exit settings for
the selected driver, see “RECALL EXIT SETTINGS”
or “STORE EXIT SETTINGS” later in this section.
RECALL DRIVER SETTINGS
To recall driver settings, use the following
procedure:
1. Enter the memory programming mode for
your driver settings by following the
instructions listed previously under “Entering
the Driver Selection Submenu.”
2. From the DRIVER SELECTION submenu, turn
the tune/select knob to scroll to RECALL
DRIVER SETTINGS and press in the knob.
If the vehicle is in PARK (P), one beep will
sound and your previously saved driving
position will then be recalled.
If the vehicle is not in PARK (P), three beeps
will sound and your previously saved
driving position will not be recalled.
A memory recall can be stopped by pressing any
memory seat or mirror position button.
If you would like the stored driving positions to be
recalled when unlocking your vehicle with the
keyless access transmitter or when starting your
vehicle, see “REMOTE RECALL MEMORY”
or “START BUTTON RECALL” underVehicle
Personalization on page 148.
171

Passenger Airbag Status Indicator............. 245
Charging System Light.............................. 247
Brake System Warning Light..................... 248
Anti-Lock Brake System Warning Light...... 249
Low Tire Pressure Warning Light.............. 249
Traction Control System (TCS)
Warning Light........................................ 250
Engine Coolant Temperature
Warning Light........................................ 251
Engine Coolant Temperature Gage............ 251
Malfunction Indicator Lamp........................ 252
Oil Pressure Light..................................... 255
Security Light............................................ 256
Fog Lamp Light......................................... 256
Lights On Reminder.................................. 256
Cruise Control Light.................................. 256
Highbeam On Light................................... 257
Fuel Gage................................................. 257Driver Information Center (DIC).................. 258
DIC Controls and Displays........................ 258
DIC Warnings and Messages.................... 264
Other Messages........................................ 279
Audio System(s)......................................... 280
Setting the Time........................................ 281
Radio with CD........................................... 282
Using an MP3........................................... 297
XM Radio Messages................................. 303
Navigation/Radio System........................... 305
Radio Personalization................................ 305
Theft-Deterrent Feature............................. 309
Audio Steering Wheel Controls.................. 310
Radio Reception........................................ 312
Care of Your CDs..................................... 313
Care of the CD Player.............................. 313
Diversity Antenna System.......................... 314
XM™ Satellite Radio Antenna System....... 314
Section 3 Instrument Panel
176

Warning the Driver
The alert symbol will
ash on the HUD and
a warning beep will
sound when driver
action may be required.
The driver warning is active when:
You are approaching a vehicle too quickly.
You are following a vehicle ahead much
too closely.
SeeDefensive Driving on page 316for more
information.
Detecting the Vehicle Ahead
The vehicle ahead symbol will only appear on the
HUD when a vehicle ahead of you is detected in
your path. If this symbol does not appear, or
disappears briey, FCA will not respond to vehicles
you may see ahead. The symbol may disappear on
curves, highway exit ramps, or hills. Also, when
another vehicle enters the same lane as you, the
FCA system will not detect the vehicle until it is
completely in your driving lane.
{CAUTION:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not
detect a vehicle ahead. FCA may not
help you avoid a collision under these
conditions. Do not use FCA when the radar
is blocked by snow, ice, or dirt. Keep your
radar clean. See “Cleaning the System”
underAdaptive Cruise Control on page 197.
{CAUTION:
FCA may not detect and warn soon
enough to stationary or slow-moving
vehicles or other objects ahead of you.
You could crash into an object ahead
of you. Do not rely on FCA when
approaching stationary or slow-moving
vehicles or other objects.
187

Unnecessary Warnings
FCA may occasionally provide an unnecessary
warning to guard rails, signs, and other stationary
objects. This is normal operation, your vehicle
does not need service.
Other Messages
There are three messages that may appear on the
Driver Information Center (DIC). They are
CLEAN RADAR, RADAR CRUISE NOT READY
and SERVICE RADAR CRUISE. SeeDIC
Warnings and Messages on page 264.
Cleaning the System
The radar can become blocked by snow, ice, or
dirt. If so, you may need to turn off the engine and
clean the lens. See “Cleaning the System”
underAdaptive Cruise Control on page 197.
Flash-to-Pass
This feature allows you to use the high-beam
headlamps to signal the driver in front of you that
you want to pass.
Pull and hold the turn signal/multifunction lever
toward you to use this feature. When you do this,
the following will occur:
If the headlamps are off, in low-beam or in
Daytime Running Lamps (DRL) mode, the
high-beam headlamps will turn on. They will
stay on as long as you hold the lever
there. Release the lever to turn them off.
If the headlamps are in high-beam mode, they
will switch to low beam. To return to
high-beam, push the lever away from you.
188

The mist and wash cycles operate as normal and
are not affected by the Rainsense™ function.
The Rainsense™ system can be overridden at any
time by manually turning the wiper band to low
or high speed.
When Rainsense™ is active, the headlamps will
turn on automatically. The headlamps will turn
off again once the wipers turn off if it is light
enough outside. If it is dark, they will remain on.
SeeWiper Activated Headlamps on page 215.
Notice:Do not place stickers or other items
on the exterior glass surface directly in front of
the moisture sensor. Doing this could cause
the moisture sensor to malfunction.
Windshield Washer
K(Washer Fluid):The lever on the right side
of the steering column also controls the windshield
washer. There is a button at the end of the
lever. To spray washer uid on the windshield,
press the button and hold it. The washer will spray
until you release the button. The wipers will
continue to clear the window for about six seconds
after the button is released and then stop or
return to your preset speed.
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
If the uid in the windshield washer uid reservoir
is low, the message CHECK WASHER FLUID
will appear on the Driver Information Center (DIC)
display. It will take 60 seconds after the bottle
is relled for this message to turn off. For
information on the correct washer uid mixture to
use, seeWindshield Washer Fluid on page 404
andRecommended Fluids and Lubricants on
page 516.
191

Approaching and Following a Vehicle
The vehicle ahead
symbol will only appear
on the HUD when a
vehicle ahead is
detected in your path.
If this symbol does not appear, or disappears
briey, Adaptive Cruise Control will not respond to
vehicles you may see ahead.
{CAUTION:
When the Adaptive Cruise Control radar is
blocked by snow, ice, or dirt, it may not
detect a vehicle ahead. Adaptive Cruise
Control may not have time to slow your
vehicle enough to avoid a collision.
CAUTION: (Continued)
CAUTION: (Continued)
Do not use Adaptive Cruise Control when
the radar is blocked by snow, ice, or dirt.
Keep your radar clean. See “Cleaning the
System” later in this section.
Adaptive Cruise Control will, automatically, slow
your vehicle down when approaching a slower
moving vehicle. It will then adjust your speed to
follow the vehicle in front at the selected follow
distance. Your speed will increase or decrease to
follow the vehicle in front of you but will not
exceed the set speed. It may apply limited braking,
if necessary. When braking is active, your brake
lights will come on. It may feel or sound different
than if you were applying the brakes yourself. This
is normal.
205

Other Messages
There are three messages that may appear on the
DIC. They are SERVICE RADAR CRUISE,
RADAR CRUISE NOT READY and CLEAN
RADAR. These messages will appear to indicate
a problem with the Adaptive Cruise Control.
SeeDIC Warnings and Messages on page 264
for more information.
Cleaning the System
The radar can become blocked by snow, ice or
dirt. If so, you may need to turn off the engine and
clean the lens. Remember, do not use Adaptive
Cruise Control in icy conditions, or when visibility is
low, such as in fog, rain or snow.
The emblem/lens is located in the center of
the grille.
To clean the emblem/lens, wipe the surface with a
soft cloth. After cleaning the emblem/lens,
engage the Adaptive Cruise Control. If you are
unable to do so, see your dealer.
Headlamps
The exterior lamp control is located in the middle
of the turn signal/multifunction lever.
O(Exterior Lamp Control):Turn the control
with this symbol on it to operate the exterior lamps.
The exterior lamp control has four positions:
O(On/Off):Turn the control to this position to
turn off all lamps and automatic lighting features
including Daytime Running Lamps (DRL) and
IntelliBeam™.
211