wiper blades CADILLAC XLR 2005 1.G Owners Manual

&(Delay):Move the lever to this position to activate
the Rainsense™ function. Adjustments in this region
change the sensitivity of the Rainsense™ system.
9(Off):Move the lever to this position to turn off the
windshield wipers.
8(Mist):Move the lever all the way down to mist and
release for a single wiping cycle. The windshield
wipers will stop after one wipe. If you want more wipes,
hold the band on mist longer.
Heavy snow or ice can overload the wipers. If this
occurs, a circuit breaker will stop the wipers until the
motor cools. So, be sure to clear any ice and snow from
the windshield wiper blades before using them. If the
wiper blades are frozen to the windshield, carefully
loosen them or warm the windshield before turning the
wipers on. If your blades do become worn or
damaged, get new blades or blade inserts.
Rainsense™ Wipers
Your vehicle has Rainsense™ wipers. The moisture
sensor for this feature is mounted on the interior side of
the windshield below the rearview mirror and is used
to automatically operate the wipers by monitoring
the amount of moisture build-up on the windshield.
Wipes occur as needed to clear the windshield
depending on driving conditions and the sensitivity
setting. In light rain or snow, fewer wipes will occur. In
heavy rain or snow, wipes will occur more frequently.
The Rainsense™ wipers operate in a delay mode
as well as a continuous low or high speed as needed. If
the system is left on for long periods of time, occasional
wipes may occur without any moisture on the
windshield. This is normal and indicates that the
Rainsense™ system is activated.
The Rainsense™ system is also sensitive to vibration.
The system may activate if something hits the
windshield or if the vehicle hits a bump.
3-10

Driving in Rain and on Wet Roads
Rain and wet roads can mean driving trouble. On a wet
road, you cannot stop, accelerate, or turn as well
because your tire-to-road traction is not as good as on
dry roads. And, if your tires do not have much tread
left, you will get even less traction. It is always wise to
go slower and be cautious if rain starts to fall while
you are driving. The surface may get wet suddenly when
your reexes are tuned for driving on dry pavement.The heavier the rain, the harder it is to see. Even if your
windshield wiper blades are in good shape, a heavy
rain can make it harder to see road signs and
traffic signals, pavement markings, the edge of the road,
and even people walking.
It is wise to keep your windshield wiping equipment in
good shape and keep your windshield washer tank lled
with washer uid. Replace your windshield wiper
inserts when they show signs of streaking or missing
areas on the windshield, or when strips of rubber start to
separate from the inserts.
Driving too fast through large water puddles or even
going through some car washes can cause problems,
too. The water may affect your brakes. Try to avoid
puddles. But if you cannot, try to slow down before you
hit them.
{CAUTION:
Wet brakes can cause accidents. They will not
work as well in a quick stop and may cause
pulling to one side. You could lose control of
the vehicle.
After driving through a large puddle of water
or a car wash, apply your brake pedal lightly
until your brakes work normally.
5-18

Once you are moving on the freeway, make certain you
allow a reasonable following distance.
Expect to move slightly slower at night.
When you want to leave the freeway, move to the
proper lane well in advance. If you miss your exit, do
not, under any circumstances, stop and back up. Drive
on to the next exit.
The exit ramp can be curved, sometimes quite sharply.
The exit speed is usually posted. Reduce your speed
according to your speedometer, not to your sense
of motion. After driving for any distance at higher
speeds, you may tend to think you are going slower
than you actually are.
Before Leaving on a Long Trip
Make sure you are ready. Try to be well rested. If you
must start when you are not fresh — such as after
a day’s work — do not plan to make too many miles that
rst part of the journey. Wear comfortable clothing
and shoes you can easily drive in.
Is your vehicle ready for a long trip? If you keep it
serviced and maintained, it is ready to go. If it needs
service, have it done before starting out. Of course, you
will nd experienced and able service experts in GM
dealerships all across North America. They will be ready
and willing to help if you need it.Here are some things you can check before a trip:
Windshield Washer Fluid:Is the reservoir full? Are
all windows clean inside and outside?
Wiper Blades:Are they in good shape?
Fuel, Engine Oil, Other Fluids:Have you checked
all levels?
Lamps:Are they all working? Are the lenses clean?
Tires:They are vitally important to a safe,
trouble-free trip. Is the tread good enough for
long-distance driving? Are the tires all inated to the
recommended pressure?
Weather Forecasts:What is the weather outlook
along your route? Should you delay your trip a
short time to avoid a major storm system?
Maps:Do you have up-to-date maps?
5-22

Appearance Care............................................6-70
Fabric/Carpet...............................................6-70
Vinyl...........................................................6-72
Leather.......................................................6-72
Instrument Panel..........................................6-72
Interior Plastic Components............................6-72
Wood Panels...............................................6-72
Speaker Covers............................................6-73
Glass Surfaces.............................................6-73
Care of Safety Belts......................................6-73
Weatherstrips...............................................6-73
Washing Your Vehicle...................................6-74
Cleaning Exterior Lamps/Lenses.....................6-74
Finish Care..................................................6-74
Windshield and Wiper Blades.........................6-75
Aluminum or Chrome-Plated Wheels................6-76
Tires...........................................................6-76Sheet Metal Damage.....................................6-77
Finish Damage.............................................6-77
Underbody Maintenance................................6-77
Chemical Paint Spotting.................................6-77
Vehicle Care/Appearance Materials..................6-78
Vehicle Identication......................................6-79
Vehicle Identication Number (VIN).................6-79
Service Parts Identication Label.....................6-79
Electrical System............................................6-80
Add-On Electrical Equipment..........................6-80
Windshield Wiper Fuses................................6-80
Power Windows and Other Power Options.......6-80
Fuses and Circuit Breakers............................6-80
Instrument Panel Fuse Block..........................6-81
Underhood Fuse Block..................................6-83
Capacities and Specications..........................6-85
Section 6 Service and Appearance Care
6-2

Windshield Wiper Blade
Replacement
Windshield wiper blades should be inspected at least
twice a year for wear or cracking. See “Wiper Blade
Check” underScheduled Maintenance on page 7-4.
It is a good idea to clean or replace the wiper blade
assembly on a regular basis or when worn. For proper
windshield wiper blade length and type, seeNormal
Maintenance Replacement Parts on page 7-13.
To replace the wiper blade assembly, do the following:
1. Place the vehicle in accessory mode and turn
the wipers on. Position the wipers on the
windshield in the mid-wipe position. Then with a
door open, turn the vehicle off.2. Tip the blade up and push down on the tab to
release the wiper blade assembly.
3. To install, align the wiper blade with the loop on
the wiper blade assembly, and push up to snap it
into place.
6-45

Notice:Machine compounding or aggressive
polishing on a basecoat/clearcoat paint nish may
damage it. Use only non-abrasive waxes and
polishes that are made for a basecoat/clearcoat
paint nish on your vehicle.
Foreign materials such as calcium chloride and other
salts, ice melting agents, road oil and tar, tree sap, bird
droppings, chemicals from industrial chimneys, etc.,
can damage the vehicle’s nish if they remain on painted
surfaces. Wash the vehicle as soon as possible. If
necessary, use non-abrasive cleaners that are marked
safe for painted surfaces to remove foreign matter.
Exterior painted surfaces are subject to aging, weather,
and chemical fallout that can take their toll over a period
of years. To help keep the paint nish looking new, keep
the vehicle in a garage or covered whenever possible.Windshield and Wiper Blades
If the windshield is not clear after using the windshield
washer, or if the wiper blade chatters when running,
wax, sap, or other material may be on the blade
or windshield.
Clean the outside of the windshield with a glass
cleaning liquid or powder and water solution. The
windshield is clean if beads do not form when it is rinsed
with water.
Grime from the windshield will stick to the wiper blades
and affect their performance. Clean the blade by
wiping vigorously with a cloth soaked in full-strength
windshield washer solvent. Then rinse the blade
with water.
Check the wiper blades and clean them as necessary;
replace blades that look worn.
6-75

Scheduled Maintenance
Service MaintenanceIMaintenanceII
Change engine oil and lter. SeeEngine Oil on page 6-13. Reset oil life
system. SeeEngine Oil Life System on page 6-16.An Emission Control
Service.••
Visually check for any leaks or damage.See footnote (a).••
Inspect engine air cleaner lter. If necessary, replace lter. SeeEngine Air
Cleaner/Filter on page 6-18.An Emission Control Service. See footnotes †
and (h).•
Check engine coolant and windshield washer uid levels and add uid as
needed.••
Perform any needed additional services. See “Additional Required Services” in
this section.••
Inspect wiper blades.See footnote (b).•
Inspect restraint system components.See footnote (c).•
Lubricate body components.See footnote (d).•
Replace passenger compartment air lter.See footnote (e).•
7-5

Maintenance Footnotes
†The U.S. Environmental Protection Agency or the
California Air Resources Board has determined that the
failure to perform this maintenance item will not nullify
the emission warranty or limit recall liability prior to
the completion of the vehicle’s useful life. We, however,
urge that all recommended maintenance services be
performed at the indicated intervals and the
maintenance be recorded.
(a)A uid loss in any vehicle system could indicate a
problem. Have the system inspected and repaired
and the uid level checked. Add uid if needed.
(b)Visually inspect wiper blades for wear or cracking.
Replace blade inserts that appear worn or damaged
or that streak or miss areas of the windshield.
(c)Make sure the safety belt reminder light and all your
belts, buckles, latch plates, retractors and anchorages
are working properly. Look for any other loose or
damaged safety belt system parts. If you see anything
that might keep a safety belt system from doing its
job, have it repaired. Have any torn or frayed safety belts
replaced. Also look for any opened or broken airbag
coverings, and have them repaired or replaced.
(The airbag system does not need regular maintenance.)(d)Lubricate the trunk key lock cylinder. Lubricate all
body door hinges. Lubricate all hinges and latches,
including those for the hood, trunk, console door and
any folding seat hardware. More frequent lubrication
may be required when exposed to a corrosive
environment. Applying silicone grease on weatherstrips
with a clean cloth will make them last longer, seal
better and not stick or squeak.
(e)If you drive regularly under dusty conditions, the
lter may require replacement more often.
(f)Change automatic transmission uid and lter if the
vehicle is mainly driven under one or more of these
conditions:
In heavy city traffic where the outside temperature
regularly reaches 90°F (32°C) or higher.
In hilly or mountainous terrain.
Uses such as high performance operation.
(g)Drain, ush and rell cooling system. See Engine
Coolant on page 6-20for what to use. Inspect hoses.
Clean radiator, condenser, pressure cap and ller neck.
Pressure test the cooling system and pressure cap.
(h)If you drive regularly under dusty conditions, inspect
the lter at each engine oil change.
7-7

A
Accessory Power Outlets.................................3-38
Adaptive Cruise Control...................................3-16
Additives, Fuel................................................. 6-6
Add-On Electrical Equipment............................6-80
Air Cleaner/Filter, Engine.................................6-18
Air Conditioning..............................................3-40
Airbag
Off Light.....................................................3-50
Readiness Light..........................................3-49
Airbag Sensing and Diagnostic Module (SDM)...... 8-9
Airbag System................................................1-36
Airbag Off Switch........................................1-44
How Does an Airbag Restrain?......................1-42
Servicing Your Airbag-Equipped Vehicle..........1-47
What Makes an Airbag Inate?......................1-42
What Will You See After an Airbag Inates?........1-43
When Should an Airbag Inate?....................1-41
Where Are the Airbags?...............................1-38
Antenna, Diversity Antenna System...................3-81
Antenna, XM™ Satellite Radio Antenna System.....3-81
Anti-Lock Brake System (ABS)........................... 5-6
Anti-Lock Brake, System Warning Light..............3-53
Appearance Care............................................6-70
Aluminum or Chrome-Plated Wheels..............6-76
Care of Safety Belts....................................6-73Appearance Care (cont.)
Chemical Paint Spotting...............................6-77
Cleaning Exterior Lamps/Lenses....................6-74
Fabric/Carpet..............................................6-70
Finish Care.................................................6-74
Finish Damage............................................6-77
Glass Surfaces............................................6-73
Instrument Panel.........................................6-72
Interior Plastic Components...........................6-72
Leather......................................................6-72
Sheet Metal Damage...................................6-77
Speaker Covers..........................................6-73
Tires..........................................................6-76
Underbody Maintenance...............................6-77
Vehicle Care/Appearance Materials................6-78
Vinyl..........................................................6-72
Washing Your Vehicle...................................6-74
Weatherstrips..............................................6-73
Windshield and Wiper Blades........................6-75
Wood Panels..............................................6-72
Ashtrays........................................................3-39
Audio System.................................................4-45
Audio System(s).............................................3-78
Audio Steering Wheel Controls......................3-79
Care of Your CD Player...............................3-80
Care of Your CDs........................................3-80
Diversity Antenna System.............................3-81
1

Child Restraints (cont.)
Securing a Child Restraint in the Passenger
Seat Position...........................................1-32
Top Strap...................................................1-27
Cigarette Lighter.............................................3-39
Cleaning
Aluminum or Chrome-Plated Wheels..............6-76
Exterior Lamps/Lenses.................................6-74
Fabric/Carpet..............................................6-70
Finish Care.................................................6-74
Glass Surfaces............................................6-73
Instrument Panel.........................................6-72
Interior Plastic Components...........................6-72
Leather......................................................6-72
Speaker Covers..........................................6-73
Tires..........................................................6-76
Underbody Maintenance...............................6-77
Vinyl..........................................................6-72
Washing Your Vehicle...................................6-74
Weatherstrips..............................................6-73
Windshield and Wiper Blades........................6-75
Wood Panels..............................................6-72
Climate Control System
Air Filter, Passenger Compartment.................3-45
Dual..........................................................3-40
Outlet Adjustment........................................3-45Control of a Vehicle.......................................... 5-5
Convenience Net............................................2-44
Coolant
Engine Temperature Gage............................3-54
Heater, Engine............................................2-24
Surge Tank Pressure Cap.............................6-23
Cooled Seats................................................... 1-3
Cooling System..............................................6-26
Courtesy Lamps.............................................3-33
Cruise Control, Adaptive..................................3-16
Cruise Control Lever.......................................3-12
Cupholder(s)..................................................2-42
Customer Assistance Information
Courtesy Transportation.................................. 8-7
Customer Assistance for Text Telephone (TTY)
Users....................................................... 8-4
Customer Assistance Offices........................... 8-4
Customer Satisfaction Procedure..................... 8-2
GM Mobility Reimbursement Program............... 8-5
Reporting Safety Defects to General Motors.......8-11
Reporting Safety Defects to the Canadian
Government............................................8-11
Reporting Safety Defects to the United States
Government............................................8-11
Roadside Service.......................................... 8-6
Service Publications Ordering Information........8-12
3