service reset CADILLAC XLR 2008 1.G User Guide

How to Reset the Engine Oil Life
System and the Oil Life Indicator
The Engine Oil Life System calculates when to change
the engine oil and lter based on vehicle use.
Whenever the oil is changed, reset the system so it can
calculate when the next oil change is required. If a
situation occurs where you change the oil prior
to a CHANGE OIL NOW message in the DIC being
turned on, reset the system.
After the oil has been changed, the CHANGE OIL NOW
message and the oil life indicator must be reset. To
reset the message:
1. Press the up or down arrow to scroll the DIC to
show OIL LIFE.
2. Once the XXX% ENGINE OIL LIFE menu item is
highlighted, press and hold the RESET button until
the percentage shows 100%.
If the percentage does not return to 100% or if the
CHANGE OIL NOW message comes back on
when you start your vehicle, the engine oil
life system has not reset. Repeat the procedure.
What to Do with Used Oil
Used engine oil contains certain elements that can be
unhealthy for your skin and could even cause cancer.
Do not let used oil stay on your skin for very long. Clean
your skin and nails with soap and water, or a good
hand cleaner. Wash or properly dispose of clothing or
rags containing used engine oil. See the manufacturer’s
warnings about the use and disposal of oil products.
Used oil can be a threat to the environment. If you
change your own oil, be sure to drain all the oil from the
lter before disposal. Never dispose of oil by putting it
in the trash, pouring it on the ground, into sewers, or into
streams or bodies of water. Instead, recycle it by
taking it to a place that collects used oil. If you have a
problem properly disposing of used oil, ask your
dealer/retailer, a service station, or a local recycling
center for help.
6-21

If you get the overheat warning with no sign of steam,
try this for a minute or so:
1. In heavy traffic, let the engine idle in NEUTRAL (N)
while stopped. If it is safe to do so, pull off the road,
shift to PARK (P) or NEUTRAL (N) and let the
engine idle.
2. Set the climate controls to the highest heat setting
and fan speed and open the windows as necessary.
If you no longer have the overheat warning, you
can drive. Just to be safe, drive slower for about
10 minutes. If the warning does not come back on,
you can drive normally.
If the warning continues, pull over, stop, and park your
vehicle right away.
If there is still no sign of steam, idle the engine for
three minutes while you are parked. If you still have the
warning, turn off the engine and get everyone out of
the vehicle until it cools down. Also, see “Overheated
Engine Protection Operating Mode” later in this section.
You may decide not to lift the hood but to get service
help right away.Overheated Engine Protection
Operating Mode
This operating mode allows your vehicle to be driven to
a safe place in an emergency situation. If an overheated
engine condition exists and the DIC message ENGINE
HOT, STOP ENGINE is displayed, an overheat
protection mode which alternates ring groups of
cylinders helps prevent engine damage. In this mode,
you will notice a signicant loss in power and engine
performance. Driving extended miles (km) in the
overheat protection mode should be avoided.
Notice:After driving in the overheated engine
protection operating mode, to avoid engine damage,
allow the engine to cool before attempting any
repair. The engine oil will be severely degraded.
Repair the cause of coolant loss, change the oil
and reset the oil life system. SeeEngine Oil
on page 6-16.
6-29

Headlamp Aiming
The high intensity discharge (HID) visual optical aiming
type headlamps have been preset at the factory and
should need no further adjustment. If you suspect that
the headlamps need to be reaimed, it is recommended
that you contact your dealer/retailer for service.
However, it is possible for you to re-aim your headlamps
as described in the following procedure.
Notice:To make sure your headlamps are aimed
properly, read all the instructions before beginning.
Failure to follow these instructions could cause
damage to headlamp parts.The vehicle should be properly prepared as follows:
The vehicle should be placed so the headlamps are
25 ft (7.6 m) from a light colored wall.
The vehicle must have all four tires on a perfectly
level surface which is level all the way to the wall.
The vehicle should be placed so it is perpendicular
to the wall.
The vehicle should not have any snow, ice or mud
attached to it.
The vehicle should be fully assembled and all other
work stopped while headlamp aiming is being done.
The vehicle should be normally loaded with a
full tank of fuel and one person or 160 lbs (75 kg)
on the driver seat.
Tires should be properly inated.
Start the vehicle and rock it to level the suspension.
6-47

Tire Inspection and Rotation
We recommend that you regularly inspect your
vehicle’s tires for signs of wear or damage.
SeeWhen It Is Time for New Tires on page 6-66
for additional information.
If your vehicle has P235/50R18 size tires they
should be rotated any time you notice unusual
wear. Rotate the tires as soon as possible
and check wheel alignment. Also check for
damaged tires or wheels. SeeWhen It Is Time for
New Tires on page 6-66andWheel Replacement
on page 6-70.
When rotating P235/50R18 size tires, always use
the correct rotation pattern shown here.After the tires have been rotated, adjust the front
and rear ination pressures as shown on the Tire
and Loading Information label, seeInflation - Tire
Pressure on page 6-60andLoading Your Vehicle
on page 5-22. Vehicles that have the Tire Pressure
Monitor System (TPMS) need the TPMS sensors
reset after a tire rotation is performed. A special tool
is needed to reset the sensor identication codes.
See your dealer/retailer for service. Make certain
that all wheel nuts are properly tightened. See
Wheel Replacement on page 6-70and “Wheel Nut
Torque” underCapacities and Specifications on
page 6-97
.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after a time. The wheel
could come off and cause a crash. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if you need to, to get all the rust or
dirt off.
6-65

Scheduled Maintenance
To maintain the ride, handling, and performance of your
vehicle, it is important that the rst tire rotation service be
performed when you notice unusual wear. Check tires for
ination pressures and wear. SeeTires on page 6-52.If
tire rotation is recommended for your vehicle, rotate tires.
SeeTire Inspection and Rotation on page 6-65.
When the CHANGE OIL NOW message in the Driver
Information Center (DIC) comes on, it means that service
is required for your vehicle. Have your vehicle serviced as
soon as possible within the next 600 miles (1 000 km).
It is possible that, if you are driving under the best
conditions, the engine oil life system may not indicate that
vehicle service is necessary for over a year. However,
your engine oil and lter must be changed at least once
a year and at this time the system must be reset. Your
dealer/retailer has trained service technicians who will
perform this work using genuine parts and reset the
system.
If the engine oil life system is ever reset accidentally,
you must service your vehicle within 3,000 miles
(5 000 km) since your last service. Remember to reset
the oil life system whenever the oil is changed. See
Engine Oil Life System on page 6-20for information on
the Engine Oil Life System and resetting the system.When the CHANGE OIL NOW message appears, the
following services, checks, and inspections are required:
❑Change engine oil and lter. SeeEngine Oil on
page 6-16. Reset oil life system. SeeEngine Oil Life
System on page 6-20.An Emission Control Service.
❑Visually check for any leaks or damage.
See footnote (a).
❑Inspect engine air cleaner lter. If necessary, replace
lter. SeeEngine Air Cleaner/Filter on page 6-22.
See footnote (h).
❑Check tires for ination pressures and wear. SeeTires
on page 6-52. If tire rotation is recommended for your
vehicle, rotate tires. SeeTire Inspection and Rotation
on page 6-65.
❑Inspect brake system.See footnote (l).
❑Check engine coolant and windshield washer uid
levels. If you have the 4.4L V8 supercharged engine,
check intercooler uid level. Add uid as needed.
❑Perform any needed additional services. See
“Additional Required Services” in this section.
❑Inspect suspension and steering components.
See footnote (n).
❑Inspect engine cooling system.See footnote (m).
❑Inspect wiper blades.See footnote (b).
❑Inspect restraint system components.
See footnote (c).
❑Lubricate body components.See footnote (d).
7-4