CADILLAC XLR 2009 1.G Owners Manual

Twilight Sentinel®
This feature can turn the lamps on and off for you.
A light sensor on top of the instrument panel makes the
Twilight Sentinel
®work, so be sure it is not covered.
With Twilight Sentinel
®you will see the following happen:
When it is dark enough outside, the front turn signal
lamps (DRL) will go off, and the headlamps and
parking lamps will come on. The other lamps that
come on with headlamps will also come on.
When it is bright enough outside, the headlamps will
go off, and the front turn signal lamps (DRL) will
come on, as long as the exterior lamp switch is in the
AUTO position.
If the vehicle is started in a dark garage, the automatic
headlamp system will come on immediately. Once the
vehicle leaves the garage, it takes about one minute for
the automatic headlamp system to change to DRL if
it is light outside. During that delay, the instrument panel
cluster may not be as bright as usual. Make sure the
instrument panel brightness control is in full bright
position. SeeInstrument Panel Brightness on page 3-30
for more information.You can idle the vehicle with the lamps off, even when
it is dark outside. After starting the vehicle, turn the
exterior lamp control band to off, then release it.
The lamps will remain off until you turn the control
band to off again.
Twilight Sentinel
®also provides exterior illumination as
you leave the vehicle. If Twilight Sentinel®has turned
on the lamps when you turn off the ignition, the
lamps will remain on until:
The exterior lamp switch is moved from OFF to the
parking lamp position, or
the delay time selected has elapsed.
SeeDriver Information Center (DIC) on page 3-57to
select the delay time. You can also select no delay time.
If the ignition is turned off with the exterior lamp switch
in the parking lamp or headlamp position, the Twilight
Sentinel
®delay will not occur. The lamps will turn off as
soon as the switch is turned off.
The regular headlamp system should be turned on
when needed.
3-29

Exterior Lighting Battery Saver
If the manual parking lamps or headlamps have been
left on, the exterior lamps will turn off as soon as
the ignition is turned off or Retained Accessory Power
(RAP) is active. This protects against draining the
battery in case you have accidentally left the headlamps
or parking lamps on. The battery saver does not work
if the headlamps are turned on after the ignition switch is
turned to off.
If you need to leave the lamps on, use the exterior lamp
control to turn the lamps back on.
Instrument Panel Brightness
The button for this feature is located on the instrument
panel to the left of the steering column.
+
!- (Brightness):Press to change the brightness of
the instrument panel lights.
Press the DIMMER button until PANEL DIMMING
appears on the Driver Information Center (DIC). Then
use the brightness button to adjust the instrument panel
brightness. Press the top or bottom of the button to
brighten or dim the lights. SeeHead-Up Display (HUD)
on page 3-31for more information.Be sure not to have the brightness turned all the way
down with the lamps on during the day. The DIC
may not be visible.
Courtesy Lamps
When any door or the trunk lid is opened, the interior
lamps will go on unless it is bright outside.
Press the interior lamp button on the right side of the
instrument panel, to turn the courtesy lamps on or off.
Entry/Exit Lighting
With entry lighting, the interior lamps will come on when
entering the vehicle. The interior lamps will come on
for about 20 seconds when the engine is turned off.
You can turn exit and entry lighting off by quickly turning
the courtesy lamps on and off.
Reading Lamps
The inside rearview mirror includes two reading lamps.
The lamps will go on when a door is opened. When
the doors are closed, each lamp can be turned on
individually by pressing the button for that lamp.
3-30

Battery Run-Down Protection
The vehicle has a feature to help prevent the battery
from being drained, in case the underhood lamp, vanity
mirror lamps, cargo lamps, reading lamps, console,
or glove box lamps are accidentally left on, or something
is left plugged into the accessory power outlet or
cigarette lighter. If any of the accessory lamps are
left on, they will automatically time-out after about
10 minutes. To reset the battery protection, all of the
above lamps must be turned off or the ignition must be
in the ACC/ACCESSORY position.
Head-Up Display (HUD)
{CAUTION:
If the HUD image is too bright, or too high in your
eld of view, it may take you more time to see
things you need to see when it is dark outside.
Be sure to keep the HUD image dim and placed
low in your eld of view.The Head-Up Display (HUD) allows you to see some of
the driver information that appears on the instrument
panel cluster.
The information may be displayed in English or metric
units and appears as an image focused out toward
the front of the vehicle. To change from English to metric
units, seeDriver Information Center (DIC) on page 3-57.
The HUD consists of the following information:
Speedometer
Turn Signal Indicators
High-Beam Indicator Symbol
Tap-Up/Tap-Down Transmission Feature
Check Gages Message
Adaptive Cruise Control Features and Indicators
Radio Features
3-31

Continue to scan the displays, controls and driving
environment just as you would in a vehicle without HUD.
Check the instrument panel cluster, to be sure you do
not miss something important, such as a warning
light. Under important warning conditions, the CHECK
GAGES message will display in the HUD. View the
Driver Information Center (DIC) for more information.The HUD controls are
located to the left of the
steering wheel.
+
!- (Brightness):Use to adjust the brightness of the
HUD and the instrument panel cluster.
DIMMER:Use to select the HUD or the instrument
panel cluster to adjust the brightness.
HUD:Use to adjust the vertical position of the HUD
display.
3-32

To adjust the HUD so you can see it properly, do the
following:
1. Adjust the seat to a comfortable driving position.
If you change the seat position later, you may
have to re-adjust the HUD.
2. Start the engine and press the top or bottom of the
HUD button to center the HUD image in your view.
The HUD image can only be adjusted up and
down, not side-to-side.
3. Press the DIMMER button until the DIC reads
HUD DIMMING. Then use the brightness button
to adjust the desired intensity.
The brightness of the HUD image is determined by the
light conditions in the direction the vehicle is facing
and where you have the HUD set. If you are facing a
dark object or a heavily shaded area, the HUD may
anticipate that you are entering a dark area and may
begin to dim.
To turn off the HUD, press the brightness button down
until the image disappears.
Polarized sunglasses could make the HUD image
harder to see.
As light shines out from the HUD, it is possible for light
to shine back in. In rare occurrences, when the sun
is at a specic angle and position, the sun’s rays canshine back into the HUD. When this occurs, the display
device within the HUD will be temporarily illuminated.
The event will end when the vehicle’s angle to the
sun changes.
Clean the inside of the windshield as needed to remove
any dirt or lm that reduces the sharpness or clarity
of the HUD image.
To clean the HUD, spray household glass cleaner on a
soft, clean cloth. Wipe the HUD lens gently, then dry
it. Do not spray cleaner directly on the lens because the
cleaner could leak into the unit.
If the ignition is on and you cannot see the HUD image,
check to see if:
Something is covering the HUD unit.
The brightness is adjusted properly.
The HUD image is adjusted to the proper height.
Ambient light in the direction the vehicle is facing
is low.
A fuse is blown. SeeFuses and Circuit Breakers
on page 6-83.
Keep in mind that the windshield is part of the HUD
system. SeeWindshield Replacement on page 6-45.
3-33

The following Adaptive Cruise Control (ACC) messages
may appear in the HUD:
CRUISE SPEED LIMITED:This message indicates that
the vehicle speed has been reduced below the set
speed due to ACC limitations. The set speed is too high
and ACC cannot detect other vehicles at far enough
distances for the system to operate properly.
TIGHT CURVE:This message indicates that ACC
has reduced the vehicle speed due to a tight curve in
the road. Once the road straightens, ACC will return to
the selected set speed or follow distance setting.
See “Adaptive Cruise Control (ACC)” underTurn
Signal/Multifunction Lever on page 3-7for more
information.
You may also see an ACC active symbol, alert symbol
or vehicle ahead symbol. See “Adaptive Cruise
Control (ACC)” underTurn Signal/Multifunction Lever
on page 3-7for more information.Accessory Power Outlet(s)
The accessory power outlet can be used to connect
electrical equipment, such as a cellular phone.
The accessory power outlet is located inside the center
console storage compartment, on the forward left side.
To use the outlet, remove the tethered cap. When not
using it, always cover the outlet with the protective cap.
Notice:When using an accessory power outlet,
maximum electrical load must not exceed 20 amps.
Always turn off any electrical equipment when
not in use. Leaving electrical equipment on for
extended periods will drain your vehicle’s battery.
Certain electrical accessories may not be compatible
with the accessory power outlet and could result
in blown vehicle or adapter fuses. If you experience
a problem, see your dealer/retailer for additional
information on accessory power outlets.
3-34

Notice:Adding any electrical equipment to the
vehicle can damage it or keep other components
from working as they should. The repairs would not
be covered by the vehicle warranty. Do not use
equipment exceeding maximum amperage rating of
20 amperes. Check with your dealer/retailer before
adding electrical equipment.
When adding electrical equipment, be sure to follow the
installation instructions included with the equipment.
We recommend that you see a qualied technician or
your dealer/retailer for the proper installation of the
equipment.
Notice:Improper use of the power outlet can cause
damage not covered by the warranty. Do not hang
any type of accessory or accessory bracket from the
plug because the power outlets are designed for
accessory power plugs only.Ashtray(s) and Cigarette Lighter
The ashtray and cigarette lighter are located under a
lid in the front console to the right of the shift lever.
Press the left side of the lid and it will open
automatically.
To use the cigarette lighter, push it in all the way and
let go. When it is ready, it will pop back out by itself.
Notice:If papers, pins, or other ammable
items are put in the ashtray, hot cigarettes or other
smoking materials could ignite them and possibly
damage the vehicle. Never put ammable items
in the ashtray.
Notice:Holding a cigarette lighter in while it is
heating does not let the lighter back away from the
heating element when it is hot. Damage from
overheating can occur to the lighter or heating
element, or a fuse could be blown. Do not hold a
cigarette lighter in while it is heating.
3-35

Climate Controls
Dual Climate Control System
With this system the heating, cooling, and ventilation for
the vehicle can be controlled.
When the vehicle is rst started, the system will recall the
last temperature fan and mode settings for that driver.
A. Driver and Passenger
Power/Temperature
Buttons
B. Heated Seats
C. Recirculation
D. Defrost
E. Rear Window DefoggerF. Display
G. AUTO
H. Fan Control
I. Air Delivery Mode
Control
J. Air Conditioning Off
Automatic Operation
AUTO (Automatic):When this button is pressed and
the temperature is set, the system automatically controls
the temperature, air delivery mode, air conditioning
compressor and the fan speed. AUTO will appear on
the display.
1. Press the AUTO button.
2. Adjust the temperature to a comfortable setting
between 70°F (21°C) and 80°F (27°C). An initial
setting of 73°F (23°C) is suggested.
Choosing the warmest or coldest temperature
setting will not cause the system to heat or cool
any faster. If the system is set at the warmest
or coldest temperature setting, the system remains
in manual mode at that temperature and it will
not go into automatic mode.
In cold weather, the system will start at reduced fan
speeds to avoid blowing cold air into your vehicle
until warmer air is available. The system starts
out blowing air at the oor but may change modes
automatically as the vehicle warms up to maintain
the chosen temperature setting. The length of
time needed for warm up will depend on the outside
temperature and the length of time that has
elapsed since the vehicle was last driven.
3. Wait for the system to regulate. This may take from
10 to 30 minutes. Then adjust the temperature,
if necessary.
3-36

You can switch from English to metric units through the
Driver Information Center (DIC). SeeDIC Operation
and Displays on page 3-57for more information.
The air conditioning system removes moisture from the
air, so a small amount of water might drip under the
vehicle while idling or after turning off the engine.
This is normal.
Do not cover the solar sensor located in the center of
the instrument panel, near the windshield. For more
information on the solar sensor, see “Sensors” later in
this section.
Manual Operation
wPWRx(Power/Temperature):Press the PWR
button on the left side of the climate control panel to turn
the entire climate control system on or off. Press
worx
to increase or decrease the temperature inside the
vehicle.
Press the PWR button on the right side of the climate
control panel to turn the passenger climate control
system on or off. Press
worxto increase or decrease
the temperature for the passenger.If the passenger PWR button is off, the driver temperature
switch controls the temperature for the entire vehicle.
«9 ª(Fan Control):Press to increase or decrease
the fan speed. Pressing this switch cancels automatic
operation and places the system in manual mode.
Press AUTO to return to automatic operation.
If the airow seems low when the fan speed is at the
highest setting, the passenger compartment air lter
may need to be replaced. For more information,
seePassenger Compartment Air Filter on page 3-41
andScheduled Maintenance on page 7-4.
ªN«(Air Delivery Mode Control ):Press to
change the direction of the airow inside of the vehicle.
Changing the mode cancels automatic operation and
places the system in manual mode. Press the
AUTO button to return to automatic operation.
3-37

To change the current mode, select one of the following:
H(Vent):Air is directed to the instrument panel
outlets.
%(Bi-Level):Air is divided between the instrument
panel and oor outlets. In automatic operation, cooler air
is directed to the upper outlets and warmer air to the
oor outlets.
6(Floor):Air is directed to the oor outlets, with
some air directed to the windshield and side window
outlets.
-(Floor/Defog):This mode clears windows of fog or
moisture. Air is directed to the windshield, oor
outlets and side windows. In this mode, the system
turns off recirculation and runs the air conditioning
compressor unless the outside temperature is near or
below freezing.
1(Defrost):This mode removes fog or frost from the
windshield more quickly. Press to direct air to the
windshield, with some air directed to the side windows.In this mode, the system automatically turns off the
recirculation and runs the air conditioning compressor,
unless the outside temperature is near or below freezing.
Do not drive the vehicle until all the windows are clear.
A/C OFF (Air Conditioning):Press to turn off the air
conditioning compressor. Press AUTO to return to
automatic operation. The compressor cannot be turned
off in either the defrost or oor/defog mode.
?(Recirculation):Press to turn the recirculation
mode on or off. The air conditioning compressor
also comes on.
This mode recirculates and helps to quickly cool the
air inside the vehicle. It can be used to help prevent
outside air and odors from entering the vehicle.
Recirculation is not available in defrost or oor/defog
modes.
Using recirculation for long periods of time may cause
the air inside the vehicle to become too dry. To prevent
this from happening, after the air in the vehicle has
cooled, turn the recirculation mode off.
3-38