automatic transmission CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine VIN Identification Codes
The vehicle identification number (VIN) is a 17-digit combination of letters and numbers.
VIN DIGIT DESIGNATIONDEFINITION
1 World Manufacture Identifier
2 Brand Of The Vehicle
3 Vehicle Chassis Type
4 Transmission Type
5 Engine Type
6 Restraint System
7 Check Digit
8 Model Year
9 Assembly Plant
10 Production Sequence Number
• Digits #1, #2, #3 The first 3 vehicle identification number (VIN) positions are the world manufacturer identifier:
LV V represents Chery Automobile Co., Ltd.
• Digit #4 The fourth digit of the VIN code represents the brand of the vehicle:
The brand Cheryis represented by the letter D.
• Digit #5 The fifth digit of the VIN code represents the body configuration of the vehicle:
A represents three compartments, five-door, and 4X2.
B represents two compartments, five-door, and 4X2.
C represents three compartments, four-door, two-lid, and 4X2.
D represents two compartments, five-door, and 4X4.
• Digit #6 The sixth digit of the VIN code represents the type of transmission:
1 represents manual transmission.
2 represents automatic transmission.
• Digit #7 The seventh digit of the VIN code represents the type of engine:
1 represents electronically controlled gasoline engines 1.5L - 2.0L (excluding 2.0L) series.
2 represents engines smaller than 1.5L (excluding 1.5L).
4 represents 2.0L - 2.5L engines (excluding 2.5L).
VEHICLE IDENTIFICATION NUMBER (VIN)
PZSM020054
01
01–11Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine •Hoses and clamps
• Coolant temperature sensor
• Coolant temperature sensor (for instrument cluster) (with 2.4L engine)
• Heater core
Operation
The primary purpose of a cooling system is to maintain engine temperature in a range that will provide satisfactory
engine performance and emission levels under all expected driving conditions. It also provides hot coolant for heater
performance and cooling for automatic transmission oil. This is done by transferring heat from engine metal to cool-
ant, moving the heated coolant to the radiator, and then transferring the heat to the ambient air. Engine Coolant Flow Diagram - 1.6L & 1.8L & 2.0L
1 - To Heater Core
2 - Heater Core Return
3 - To Oil Cooler
4 - Oil Cooler Return
5 - To Restrictor6 - To Engine
7 - Radiator Return
8 - Restrictor Return
9 - Minor Cycle Coolant Hose
10 - To Radiator
GENERAL INFORMATION
LTSM060005
06–4Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Installation Notes:
•Check the transaxle fluid level.
Drive the vehicle until the ATF reaches oper-
ating temperature (70° - 80°C).
Park the vehicle on level ground.
Shift the gear selector lever to all gear posi- tions once, then shift to gear “N”.
Clean and check the outside of the dipstick and remove the dipstick to check the fluid
level.
Check if the transmission fluid level is within the HOT marking of the dipstick. If lower than
the HOT marking, refill the transaxle until the
fluid level is above the HOT marking.
• After installation, check for any fluid leakage and
verify the transaxle fluid level is correct. Refill the
transaxle fluid through the fill hole (1) shown in the
figure.
Automatic Shifter Selector
Removal & Installation
1. Raise and support the vehicle.
2. Disconnect the negative battery cable.
3. Remove the air cleaner and air duct assembly.
4. Remove the base mounting of the air cleaner housing assembly.
ON-VEHICLE SERVICE
LTSM080185
08
08–243Chery Automobile Co., Ltd.